Title page Nortel Networks Communication Server 1000 Nortel Networks WLAN Handset 2210 User Guide
Revision history Revision history June 2004 Standard 2.00. This document is up-issued to support the Nortel Networks WLAN Handset 2210. May 2004 Standard 1.00. This is a new document developed to support the Nortel Networks WLAN Handset 2210.
Revision history 4
Contents Contents Regulations and safety information 9 FCC Rules – Part 15............................................................................... 9 Radio Frequency (RF) information ......................................................... 10 Operational warnings ........................................................................ 10 Electromagnetic interference and compatibility....................................... 11 International certifications.............................................
Contents The headset 33 Handset display 35 User Option menu 37 Select Ring Type .................................................................................. Select Noise Mode............................................................................... View Alias IP Address .......................................................................... View Current IP Address....................................................................... Enter Extension .....................................
Contents While away from your desk 61 Use Call Forward ................................................................................ 61 Use Internal Call Forward..................................................................... 62 Talk with more than one person Use Call Join ....................................................................................... Set up a Conference call ...................................................................... Use Conferee Selectable Display...........
Contents Desktop Charger 87 Use the Desktop Charger...................................................................... 88 Clean the Desktop Charger................................................................... 89 Terms you should know 91 Index 95 8 Draft 0.
Regulations and safety information Regulations and safety information FCC Rules – Part 15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Regulations and safety information Radio Frequency (RF) information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulations and safety information CAUTION Loud noise environment: The WLAN Handset 2210 has been designed to produce optimal voice quality. However, when used in extremely loud noise environments (for example, close to working heavy machinery), users may experience degradation in call quality performance due to echo. Avoid using the handset when traversing these types of environments.
Regulations and safety information Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio product in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Medical devices Pacemakers: The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio product and a pacemaker.
Regulations and safety information International certifications Table 1 shows the international certifications applicable to the 2210 Wireless Handset.
Regulations and safety information Specific Absorption Rate (SAR) information Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S.
Regulations and safety information The only authorized headsets that may be utilized with the Nortel Networks WLAN Handset 2210 are those obtainable from Nortel Networks or it's reseller partners. The measured SAR of the SNP2400 Wireless Handset is: 0.0495W/kG @ 2412 MHz (head) 0.0309W/kG @ 2412 MHz (body). IMPORTANT! Phone Operation Normal Position: Hold the phone as you would any other telephone, with the earpiece to your ear and speak into the microphone.
Regulations and safety information 16
Your WLAN Handset 2210 Your WLAN Handset 2210 This document describes the 2210 Wireless Handset and its features when operating on Nortel Networks Communication Server 1000. The 2210 Wireless Handset is a fully functional handset specifically designed for the busy office environment. Note: Not all features described in this guide are available on all handsets. Consult your network administrator to verify which features are available for your use.
Your WLAN Handset 2210 Figure 1 2210 Wireless Handset controls Handset controls and descriptions Use the Power On/Start Call key to turn on your 2210 Wireless Handset. This key also affects some of the states of the handset (see Table 2 on page 20). Use the Power Off/End Call key to terminate an active call and turn off the handset. Press the Menu key to view the full description of the soft key abbreviations and access the handset features. Press and hold Power On/Start Call. Two chirps sound.
Your WLAN Handset 2210 Up, Down, and Select buttons. Use the Line key to access the Feature Keys menu. Select these features by pressing the number key associated with each feature. Note: The Line key accesses the six Feature Keys located at the top of an i2004 Internet Telephone display area. Use the Function key to access the handset functions when in the active (idle) state (see Table 3 on page 21). The Function key also provides access to the User Option menu in the standby state.
Your WLAN Handset 2210 The states of the handset The 2210 Wireless Handset can be in one of seven states (see Table 2). Table 2 The seven states of the 2210 Wireless Handset (Part 1 of 2) State Description Power off The handset is turned off. It is not registered with the Call Server. Normally the handset enters the power-off state when the user presses the Power Off/End Call key for approximately two seconds when the set is in the standby state. The batteries can be recharged in the power-off state.
Your WLAN Handset 2210 Table 2 The seven states of the 2210 Wireless Handset (Part 2 of 2) State Description Active call The handset enters the active call state when a user is in an active conversation. To enter this state, the user either makes a call or answers an incoming call. Push-to-talk The Push-to-talk state begins with the first Push-to-talk transmission and ends when there has been no two-way radio traffic on the channel for 10 seconds.
Your WLAN Handset 2210 Table 3 2210 Wireless Handset function menu items (Part 2 of 2) Function menu item Function Description 3 Goodbye Use the Goodbye function to enter the active (idle) state to access the function menu. This is particularly useful if you want to make another call immediately. Simply press the FCN and 3 keys, then dial the number. Note: If you do not intend to make another call, press the Power Off/End Call key to end your current call and place the handset in the standby state.
Cleaning your handset Cleaning your handset The 2210 Wireless Handset occasionally needs to be cleaned to maintain appearance. In general, wiping the handset surface with a clean water-dampened cloth or paper towel removes most films or residues. If more rigorous cleaning is required, you can use: • A mild detergent solution. Be sure to wipe away any detergent residue with a plain water-dampened cloth. • Any general-purpose household glass and surface cleaner. Do not spray the handset directly.
Cleaning your handset 24
Basic handset operation Basic handset operation Turn on the 2210 Wireless Handset To turn on the handset: 1. Press and hold the Power On/Start Call key for two seconds. Two chirps sound. 2. Release the Power On/Start Call key. The in-service tone sounds and the extension number displays. The handset is now in standby mode and ready to make and receive calls. Turn off the 2210 Wireless Handset To turn off the handset: Press and hold the Power Off/End Call key.
Basic handset operation To make a call using a line: + 1. Press the Function key and the number 3 key to enter the active (idle) state. 2. Press the Line key and the number key (1 through 6) for the desired line. 3. Dial the number. Dial calls exactly as you would with a regular telephone. You can dial extension numbers, internal numbers, or make external calls, depending on your system. 1. Connect the headset to the headset jack. 2.
Basic handset operation 4. Press the number key corresponding to the flashing line number. To answer a headset call: When a headset is plugged into the handset, press any key other than Power On/Start Call, Power Off/End Call, soft keys or the side buttons. Hang up a call To hang up the handset: Press the Power Off/End Call key. Be sure to do this at the end of each call.
Basic handset operation Activate the backlight To activate the backlight: Press any key to activate the backlight. It also activates when there is an incoming call. The backlight turns off after 10 seconds if no key is pressed.
Feature and function activation Feature and function activation You can view the features and functions programmed in your system using the Shortcut menu, soft key features, and the Line (DN) features. You can access some functions and features using one or more or the methods described in this section. Shortcut menu – MENU key Use the Shortcut menu to view the full description of the soft key abbreviations and access the handset features. To activate a feature using the Shortcut menu: 1.
Feature and function activation 2. Press the Function key to display the first four functions in the display area. Repeat to view more functions. 3. Press the Up and Down buttons to scroll through the list of functions. The function abbreviation is highlighted in the display area. 4. Press the Select button to activate the highlighted function. Soft key features The four soft keys on your 2210 Wireless Handset enable you to quickly activate soft key features.
Feature and function activation 3. Do one of the following: • Press the number key (1 through 6) corresponding to the desired feature. • Use the Up, Down, and Select buttons to activate a feature. Using the shortcut keys The 2210 Wireless Handset features are programmed on the following shortcut keys: • number keys 0 to 9 • * key • # key These shortcut keys display next to the feature abbreviations when viewing the features.
Feature and function activation 32
The headset The headset Nortel Networks offers optional headsets for use in noisy environments or if you need to have your hands free while talking. To use the headset, simply plug it into the jack on the bottom of the handset, if available in your region. The headset is specially designed to work with the 2210 Wireless Handset. Nortel Networks does not recommend using other headsets.
The headset 34
Handset display Handset display This section summarizes the display features of the 2210 Wireless Handset. Figure 3 2210 Wireless Handset display The 2210 Wireless Handset has three display areas: • The upper display area is a status row that displays the handset status. It can include: a battery level indicator, left and right arrows, a series of dots, and a message waiting indicator. Each dot represents a line that changes to a number when active.
Handset display 36
User Option menu User Option menu When the 2210 Wireless Handset is in standby mode (power is on, but the handset is not in use), press and briefly hold the Function key to display the User Option menu. This section describes the following standard User Option menu items: • Ring Type • Noise Mode • Alias IP Address • Current IP Address • Extension • Current Call Server • Terminal Type Check with your system administrator for specific features supported by your 2210 Wireless Handset.
User Option menu 4. Use the Up and Down buttons to scroll through the menu and highlight one of the following settings (an asterisk indicates the selected setting): • Normal: Produces an audible ring. This is the default setting. • Vibrate: Vibrates. • Vib/Norm: Vibrates for six seconds, then rings. 5. Press the Select button (or the OK soft key) to select the setting. 6. Do one of the following: Up • Press the Up soft key to return to the previous menu and set another option.
User Option menu 4. Use the Up and Down buttons to scroll through the menu and highlight one of the following settings (an asterisk indicates the selected setting): • Normal: For most office environments. This is the default setting. • High: For moderate background noise. • Severe: For extremely noisy conditions. 5. Press the Select button (or the OK soft key) to select the setting. 6. Do one of the following: Up • Press the Up soft key to return to the previous menu and set another option.
User Option menu 3. Press the Select button (or the OK soft key) to view the alias IP address for the handset. 4. Do one of the following: Up • Press the Up soft key to return to the previous menu and set another option. • Press the Power Off/End Call key to exit all menus and return to the standby state. Note: You can also press the Exit soft key from the top-level menu to exit and return to the active (off-hook) state.
User Option menu 4. Up Do one of the following: • Press the Up soft key to return to the previous menu and set another option. • Press the Power Off/End Call key to exit all menus and return to the standby state. Note: You can also press the Exit soft key from the top-level menu to exit and return to the active (off-hook) state. Enter Extension The Extension option enables the user to enter the extension number for the handset. This number is used to identify the handset.
User Option menu 6. Up Do one of the following: • Press the Up soft key to return to the previous menu and set another option. • Press the Power Off/End Call key to exit all menus and return to the standby state. Note: You can also press the Exit soft key from the top-level menu to exit and return to the active (off-hook) state. View Current Call Server The Current Call Server option shows the Call Server IP address and port number. Note: This option is for display purposes.
User Option menu View Terminal Type The Terminal Type option shows the type of PBX used by the system. Note: The Terminal Type option is for display purposes only. You cannot edit this option. To view the Terminal Type: Terminal Type Up 1. Press and hold the Function key when in standby mode. 2. Use the Up and Down buttons to scroll through the menu and select Terminal Type. 3. Press the Select button (or the OK soft key) to select the option. The terminal type displays. 4.
User Option menu 44
Call features Call features System administration is required for Call features. Contact your system administrator to ensure that these features are supported by the system software and to have them configured on your handset. IMPORTANT! Access to the features and functions in the following sections are dependent on your system configuration. Contact your system administrator to determine whether specific features are accessible through your 2210 Wireless Handset.
Call features 46
Making calls Making calls This section describes features associated with making a call. Use Autodial The Autodial feature displays, stores, and automatically dials telephone numbers. To use Autodial: AutoDial 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key (1 through 6) corresponding to the DN number to dial the number. 1. Go off-hook. 2. Press the Line key to view the first page of Autodial numbers. 3.
Making calls 6. Press the Line key again to access the Feature Keys menu. 7. Press the number key (1 through 6) corresponding to the desired location chosen in step 4 to store the number. Note: The selected line number flashes in the upper display area. Activate Ring Again Use the Ring Again feature if a busy tone sounds or when there is no answer after placing a call. Ring Again causes the ring again indicator to flash, indicating that the person you tried to call is available.
Making calls Redial last number called The Last Number Redial feature automatically redials the last dialed number. To use Last Number Redial: Redial 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key corresponding to the Last Number Redial feature. Use Speed Call By entering a one, two, or three digit code (0–999), use the Speed Call feature to store, edit, and automatically dial frequently-called telephone numbers.
Making calls SpCallCtlr 6. Press the number key (1 through 6) corresponding to the Speed Call Controller feature again to save the code and number. Note: The flashing icon turns off. To make a Speed Call: SpCallCtlr 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key (1 through 6) corresponding to the Speed Call Controller feature. 4. Dial the Speed Call code to automatically dial the number.
Making calls Use Conference Hotline Use the Conference Hotline feature to automatically dial a specific number. Other features, such as Call Redirection, can be added to Conference Hotline. Call Redirection redirects a Conference Hotline call to be answered only by a person. To use Conference Hotline: ConfHotlne 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key (1 through 6) corresponding to the Conference Hotline feature to automatically dial the number.
Making calls 52
While on an active call While on an active call This section describes features available during an active call. Place a call on hold Use the Hold feature when talking on one line and another call arrives on a second line. Retain the original call by placing it on hold and then answer the second call. To place a call on hold: Press the Function key and the number 2 key to activate the Hold function. The number corresponding to the line on hold flashes in the upper display area.
While on an active call Trns 3. When that number rings or a person answers, press the Transfer soft key again. 1. If the person called is not available, Press the Line key to access the Feature Keys menu. 2. Press the number key corresponding to the flashing line number, in the upper display area, to reconnect to the original call.
While on an active call Use Call Park Use the Call Park feature to hold temporarily (park) and retrieve a call from any telephone or handset. Using Call Park does not tie up a line and, when configured network-wide, can be used across networks. A System Park Extension can be set to automatically park most calls. To park a call on the System Park DN or your own DN: Park Park During an active call, press the Park soft key twice.
While on an active call 2. Dial a charge account number or the caller’s number. Note: For information on using the Charge key, see “Charge a call or charge a forced call” on page 72. CPrt 3. Press the Call Party soft key to return to the call. Display incoming calls Use the Display feature to display a second incoming caller’s number and name (if available) during an active call, without interfering with the call in progress.
Incoming calls Incoming calls This section describes features that are used with incoming calls. Activate Call Pickup Use the Call Pickup feature to pick up calls from any telephone or handset in the same pickup group or another pickup group. To answer a call in your own Call Pickup group: Pckp 1. Go off-hook. 2. Press the Pickup soft key. 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key corresponding to the Group Pickup feature. 4.
Incoming calls 4. Dial the DN of the handset that is ringing (in your call pickup group). If the pickup DN or group number is invalid, press the Power Off/End Call key. Use Call Waiting The Call Waiting feature alerts you to an incoming call by producing a tone. It also puts the current call on hold, while you answer the new call. To answer an incoming call while on another call: + 1. When the incoming call tone sounds, press the Function key and the number 2 key to put the current call on hold.
Incoming calls 2. Press the Line key to access the Feature Keys menu. 3. Press the number key corresponding to the first call. Note: The first call is on hold so the number indicator for that line is flashing.
Incoming calls 60
While away from your desk While away from your desk This section describes features that are used when you are away from your desk. Use Call Forward Use the Call Forward feature to direct incoming calls to ring at another Line (DN). Note: If the handset is in the process of ringing, that call cannot be forwarded. To forward your calls or change the forward number: + Frwr Frwr 1. Go off-hook. 2. Place the handset in the active (idle) state by pressing the Function key and the number 3 key. 3.
While away from your desk Use Internal Call Forward Use Internal Call Forward to accept only calls originating at internal DNs to ring at another DN. Calls originating outside your telephone system still ring at your handset. Current incoming calls cannot be forwarded. To forward internal calls: + IntForward IntForward 1. Go off-hook. 2. Place the handset in the active (idle) state by pressing the Function key and the number 3 key. 3. Press the Line key to access the Feature Keys menu. 4.
Talk with more than one person Talk with more than one person This section describes features that allow conversations among more than two people. Use Call Join Use the Call Join feature to connect calls to the current active call. This creates a conference between the two callers and yourself. To connect a call on hold (on a different line) to your current call: Conf Conf 1. Press the Conference soft key. 2. Press the Line key to access the Feature Keys menu. 3.
Talk with more than one person 4. If necessary, repeat the procedure until all required people are in the conference. 1. Press the Power Off/End Call key. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key corresponding to the flashing icon to return to your original call.
Talk with more than one person 5. Press the Power Off/End Call key. If configured, the Conference Count Display returns an updated total count of conferees. The LCD indicator turns off. 1. While on a conference call, press the Line key to access the Feature Keys menu. 2. Press the number key corresponding to the Conferee Selectable Display feature until the conferee you want to disconnect appears on the screen. 3.
Talk with more than one person GroupCall 3. Press the number key corresponding to the Group Call feature. The feature automatically calls all group members. The icon flashes until all members answer. Note 1: The line numbers of the group members appear on the display as they answer. When the last person answers, the Group Call indicator lights steadily. Note 2: When a person in your group is on a conference call or another group call, they are not connected to your group call.
Talk with more than one person To end a Group Call: Press the Power Off/End Call key. Note: When the person who made the group call disconnects, the call terminates for all members of the group. However, the members of the Group Call can disconnect from the call and not affect other members on the call.
Talk with more than one person 68
Work without interruption Work without interruption This section describes features that provide uninterrupted work time. Activate Make Set Busy Use the Make Set Busy feature to make your handset appear busy to all callers. To activate Make Set Busy: MakeSetBsy 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3. Press the number key corresponding to the Make Set Busy feature. 1. Go off-hook. 2. Press the Line key to access the Feature Keys menu. 3.
Work without interruption 70
Other call features Other call features Use Call Page Connect to make an announcement Use the Call Page Connect feature to make an announcement over a paging system. Note: A Page key on an attendant console overrides and disconnects the telephones. The telephones must re-access the Page trunk. To connect to Call Page: 1. Go off-hook. 2. Dial the Page Trunk Access Code to complete the connection to the page system. 3. Make your announcement. To disconnect Call Page: Press the Power Off/End Call key.
Other call features Charge a call or charge a forced call Use the Call Charge feature to charge a call to a specific account. The Forced Charge feature charges long-distance calls from a handset restricted to local calls. To charge a local or long-distance call to an account before you dial: Chrg Chrg 1. Go off-hook. 2. Press the Charge soft key. 3. Dial the charge account number. 4. Press the Charge soft key. 5. When the dial tone sounds, dial the number. 1.
Other call features To charge a call to an account when you transfer a call: Trns 1. Press the Transfer soft key. The call is on hold. Chrg 2. Press the Charge soft key. 3. Dial the charge account number. 4. After the dial tone, dial the number to where the call is to be transferred. 5. Press the Transfer soft key when you hear the handset ring. Trns Note: You can talk privately to the person at the transfer number before you press the Transfer key.
Other call features Use Enhanced Override Use the Enhanced Override feature to override an active call after you have attempted a Forced Camp-on. Use Enhanced Override to make a simple call or a consultation call (such as placing a call on hold and calling another party). To use Enhanced Override: Override 1. If you receive a busy signal after dialing a number, press the Line key to access the Feature Keys menu. 2.
Other call features Override 2. Press the number key corresponding to the Override feature to initiate a Forced Camp-on. Note: The person you called receives a tone, and you receive a ring/ringback signal or busy/engaged signal, depending on the options chosen. You are now camped-on to the number you dialed. 3. When the person you called finishes their call, your handset automatically dials the number. Both your handset and their handset rings.
Other call features 76
Branch Office Branch Office A Branch Office handset can operate in Normal Mode or Local Mode. Normal mode The handset registers with the Main Office and receives services from the Main Office. At any time during Normal Mode you can check local mode functionality (make and receive calls) by enabling Local Mode and returning to Normal Mode. Local mode If the WAN connection goes down, the handset loses communication with the Main Office TPS.
Branch Office 78
Hospitality features Hospitality features The hospitality features in this section are intended for hotel operations. Activate Message Registration Use the Message Registration feature to read, change, or reset meters that log your hotel calls. To read meters: + MsgReg MsgReg 1. Go off-hook. 2. Press the Function key and the number 3 key to enter the active (idle) state. 3. Press the Line key to access the Feature Keys menu. 4.
Hospitality features MsgReg 7. Press the * key. 8. Press the Line key to access the Feature Keys menu. 9. Press the number key corresponding to the Message Registration feature again. 1. Go off-hook. 2. Press the Function key and the number 3 key to enter the active (idle) state. 3. Press the Line key to access the Feature Keys menu. 4. Press the number key corresponding to the Message Registration feature. 5. Dial the room Directory Number (DN). 6. Press the * key. 7.
Hospitality features RoomStatus 4. Press the number key corresponding to the Room Status feature. 5. Dial the Directory Number (DN) for the room for which the cleaning status is being changed. 6. Dial one of the following cleaning status codes: 1 = Cleaning requested 2 = Cleaning in progress 3 = Room cleaned 4 = Room passed inspection 5 = Room failed inspection 6 = Cleaning skipped 7 = Not for sale The interrupted dial tone sounds. RoomStatus 7. Press the * key. 8. Dial the Maid ID.
Hospitality features RoomStatus 3. Press the Line key to access the Feature Keys menu. 4. Press the number key corresponding to the Room Status feature. 5. Dial the Directory Number (DN) for the room. The DN displays followed by a two-digit code. a. The first digit indicates the occupancy status: 0 = Room vacant 1 = Room occupied b.
Hospitality features 5. Dial the Directory Number (DN) for the room. The DN displays followed by a two-digit code. a. The first digit indicates the occupancy status: 0 = Room vacant 1 = Room occupied b. The next digit indicates the cleaning status of the room: 1 = Cleaning requested 2 = Cleaning in progress 3 = Room cleaned 4 = Room passed inspection 5 = Room failed inspection 6 = Cleaning skipped 7 = Not for sale RoomStatus 6. Dial the status code for the room. A three-digit code appears.
Hospitality features 84
Battery packs Battery packs The battery pack for the 2210 Wireless Handset must be recharged periodically. The Nickel Metal Hydride (NiMH) rechargeable battery pack provides four hours of talk time or 70 hours of standby time. Standby time is when the handset is turned on, but not in an active call. Refer to Figure 4 for the location of the battery pack.
Battery packs Remove and insert the battery pack To remove a battery pack: Press both battery release buttons on the left and right sides of the handset. The battery pack releases from the handset. To insert a battery pack: Slide the battery pack straight into the handset cavity. Do not force the battery pack into the handset. To change a battery pack while in a call: 86 1. Use Call Park to park the current call (see “Use Call Park” on page 55). 2.
Desktop Charger Desktop Charger The Nortel Networks WLAN Handset 2210 Desktop Charger (Figure 5) is designed to fully charge the Nickel Metal Hydride (NiMH) battery packs in approximately one and a half hours. The charger operates in a 50° to 85° F (10° to 30° C) environment. Do not expose the charger to freezing temperatures or direct sunlight. Figure 5 The 2210 Wireless Handset Desktop Charger The charger is shipped with the appropriate power supply for the site.
Desktop Charger Use the Desktop Charger To charge the Wireless Handset: 1. Press the Power Off/End Call key to terminate any calls. The handset can be off or in standby mode during charging. 2. Place the handset, face forward, into the Desktop Charger. The red indicator light turns on. Note: The indicator light does not come on when the charger slot is empty, when the handset is not inserted properly, or when the charger has no power. 3. Charge the battery pack.
Desktop Charger Clean the Desktop Charger Clean the Desktop Charger by wiping the surface with a clean, water-dampened cloth or paper towel. A mild detergent solution can be used. Be sure to wipe away any detergent residue with a plain water dampened cloth. CAUTION Do not immerse the charger in water or other liquid. Do not pour liquids into the charger slot. The battery pack contacts on the handset can be cleaned with isopropyl (rubbing) alcohol applied with a Q-tip, cloth, or paper towel.
Desktop Charger 90
Terms you should know Terms you should know Attendant A telephone operator in your organization. Autodial A telephone number programmed on the Autodial key for one-touch dialing. Call party information The display showing Call Party Name Display (CPND) information including the telephone number and name of the incoming call. The system must have CPND enabled. Desktop Charger The Desktop Charger is used to recharge the battery pack for the 2210 Wireless Handset.
Terms you should know More... An option enabling access to the multiple layers of the soft key features. These keys are the four keys located directly below the display area. Paging tone A special tone heard when using the Radio Paging feature. You hear two beeps followed by dial tone. Primary Directory Number The main extension number on your handset. It is referred to by the Primary Directory Number (PDN) key. Private Line A feature that can be assigned to your handset.
Terms you should know Status Messages A message displayed to inform the user of important information. A right arrow appears if more than one Status Message is present. Examples of Status Messages include: Message Waiting, All Lines Forwarded to: 6453, Do Not Disturb On, Ring Again active, Ringer is OFF, and Line x Unavailable. System or switch Your office communications system.
Terms you should know 94
Index Index A Active (idle) state 20 Active (off-hook) state 20 Active call state 21 Alias IP Address 39 Attendant 91 Attendant Recall 54 Auto Dial 91 Autodial 47 B Battery packs 85 Branch Office 77 C Call Forward 61 Call Join 63 Call Page Connect 71 Call Park 55 Call Party 55 Call party information 91 Call Pickup 57 Call Trace, Malicious 56 Call Waiting 58 Centrex/Exchange Switchhook Flash 71 Charge a call 72 Charge a Forced call 72 Charge the Wireless Handset 88 Clean the Desktop Charger 89 Conferee Se
Index I Indicator status 91 Insert a battery pack 86 Insert the battery pack 86 Internal Call Forward 62 Interrupted dial tone 91 Privacy Release 75 Private Line 92 Push-to-Talk state 21 R Last Number Redial 49 Line key 19 Local mode 77 Low battery indicators 85 Record a Caller’s Number 55 Redial last number called 49 Remove a battery pack 86 Remove battery pack 86 Ring Again 48 Ring Type 37 Room Status 81 M S Maid Identification 80 Make Set Busy 69 Menu key 18 Message Registration 79 More Key 92 S
Index U Up, Down, and Select buttons 19 User Interface 93 User Option menu 37, 38, 39, 40, 41, 42, 43 97
Index 98
Nortel Networks Communication Server 1000 Nortel Networks WLAN Handset 2210 User Guide Copyright © 2004 Nortel Networks and licensors All Rights Reserved Information is subject to change without notice. Nortel Networks reserves the right to make changes in design or components as progress in engineering and manufacturing warrant.
