Part No.
Copyright © Nortel Networks Limited 2005. All rights reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel.
Regulatory Compliance Statements for WLAN Access Point 2330 Federal Communications Commission (FCC) Compliance Notices This section includes the following FCC statements for the WLAN Access Point 2330: • Class B Interference Statement • RF Radiation Exposure & Hazard Warning • Non-Modification Statement • Deployment Statement Class B Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Deployment Statement This product is certified for indoor deployment only. Do not install or use this product outdoors. Canadian IC Statement Operation is subject to the following two conditions in Canada: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device To prevent radio interference to the licensed service (i.e.
German Hiermit erklärt Nortel Networks, dass sich dieser/diese/diesesRadio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklärt Nortel Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
Dynamic Frequency Selection (DFS) This device implements a DFS feature in accordance with the limits in EN 301 893 Version 1.2.3, Section 4.6 and Annex D, Tables D.1, D.2 & D.4 for a device operating in the mode defined as “Master”. Section 4.6, Tables 6 and 7 of this document define the requirements prior to using a channel and during normal operation for a Master device (i.e.
Contacting Nortel Technical Support 7 Contacting Nortel Technical Support If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance. Additional information about the Nortel Technical Solutions Centers is available from the www.nortel.com/contactus URL. An Express Routing Code (ERC) is available for many Nortel products and services.
WLAN—Access Point 2330 WLAN—Access Point 2330 Cable Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Suspended Ceiling Installation—Flush Ceiling Tiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Suspended Ceiling Installation—Drop Ceiling Tiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Junction Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspended Ceiling Installation—Flush Ceiling Tiles 9 Suspended Ceiling Installation—Flush Ceiling Tiles Mounting template Mounting bracket Use the mounting template to cut a hole for the Cat 5 cable. 2 Remove the mounting bracket from the 2330 access point. 3 Attach the mounting bracket to the T-bar clamp. 840-9502-0011 1 840-9502-0008 Access point 840-9502-0089 This procedure applies to T-bars that are 23.9 mm (15/16 inches) wide. For a 14.2-mm (9/16-inch) or 15.
Suspended Ceiling Installation—Flush Ceiling Tiles Insert the Cat 5 cable through the point connector opening in the mounting bracket, then plug the cable into the 2330. 5 Attach the 2330 to the mounting bracket.
Suspended Ceiling Installation—Drop Ceiling Tiles 11 Suspended Ceiling Installation—Drop Ceiling Tiles Access point Mounting template T-bar clamps (use set that fits T-bar) 1 Use the mounting template to cut a hole for the Cat 5 cable. 2 Install the T-bar clamp that fits the T-bar. Mounting bracket 840-9502-0088 This procedure applies to T-bars that are 23.9 mm (15/16 inches), 14.2-mm (9/16-inches), or 15.9-mm (5/8-inches) wide. You also can use this procedure for flush ceilings with 14.
Suspended Ceiling Installation—Drop Ceiling Tiles 4 Attach the mounting bracket to the T-bar clamp. Port connector opening Universal mounting bracket Universal mounting bracket T-bar 840-9502-0004 T- bar 840-9502-0012 T-bar clamps (attached to T-bar) Port connector opening (Viewed from above ceiling tiles, looking down.) Insert the Cat 5 cable through the point connector opening in the mounting bracket, then plug the cable into the 2330. 6 Attach the 2330 to the mounting bracket.
Junction Box Installation 13 Mounting bracket Remove the mounting bracket from the 2330 . 2 Attach the bracket to the junction box.
Junction Box Installation Plug the Cat 5 cable into the 2330 access point and attach the 2330 to the mounting bracket.
Solid Wall or Ceiling Installation 15 Access point Mounting template Mounting bracket Use the mounting template to cut a hole for the Cat 5 cable. 2 Remove the mounting bracket from the 2330 . 3 Attach the bracket to the wall or ceiling.
Configuring the AP 4 Plug the Cat 5 cable into the 2330 access point and attach the 2330 to the mounting bracket.