Part No.
Copyright © 2003 Nortel Networks All rights reserved. March 2003. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks Inc.
Nortel Networks Inc. software license agreement NOTICE: Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement). BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE.
4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Text conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Chapter 3 Device Manager basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Starting Device Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Setting the Device Manager properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Opening a device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Device Manager window .
Contents 7 Setting console, Telnet, and Web passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Setting remote dial-in access security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 214392-A
Figures Figure 1 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 2 IP Configuration/Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3 InstallAnywhere Introduction dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 4 License Agreement dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 5 Choose Install Set dialog box . . . . . . . .
Figures Figure 30 Pie graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Figure 31 Interface statistics for a single port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 32 Interface statistics for multiple ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 33 Statistics dialog box for a port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables Table 1 Solaris patch files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 2 Properties dialog box items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 3 SNMP community string default values . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Table 4 Open Device dialog box items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 5 Menu bar commands . . . . . . . . . . . . . . . . .
Tables 214392-A
Preface The Nortel Networks* BayStack* 380-24F Gigabit Switch management software provides the means to configure and monitor the operation of your BayStack 380-24F switches. Management software includes the console interface resident in each BayStack 380-24F Gigabit Switch; Java-based Device Manager software, which you install on a management station in the network; and a Web-based management interface accessible through a Web browser.
Preface Text conventions This guide uses the following text conventions: angle brackets (< >) Indicate that you choose the text to enter based on the description inside the brackets. Do not type the brackets when entering the command. Example: If the command syntax is ping , you enter ping 192.32.10.12 bold Courier text Indicates command names and options and text that you need to enter. Example: Enter # chmod 755 ./install_dmvm.
Preface 15 Related publications For more information about using the BayStack 380-24F Gigabit Switch, refer to the following publications: • Using the BayStack 380-24F Gigabit Switch (part number 214391-A) Describes how to install and use the BayStack 380-24F Gigabit Switch; includes instructions to use the console interface to configure the switch.
Preface How to get help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance.
Chapter 1 Management basics This chapter summarizes basic operational procedures in a BayStack 380-24F Gigabit Switch and provides an overview of switch management options.
Chapter 1 Management basics Web-based management interface The BayStack 380-24F Gigabit Switch Web-based management interface is a Web-based graphical user interface that you use with a Web browser to manage a switch. You can access devices on your network from various locations within the network. To access the Web-based management interface, you need a Web browser and an IP address for the switch.
Chapter 1 Management basics 19 Figure 1 Main menu BayStack 380-24F Main Menu IP Configuration/Setup... SNMP Configuration... System Characteristics... Switch Configuration... Console/Comm Port Configuration... Display Hardware Units... Spanning Tree Configuration... TELNET Configuration... Software Download... Configuration File... Display System Log Reset Reset to Default Settings Logout Use arrow keys to highlight option, press or to select option.
Chapter 1 Management basics Figure 2 IP Configuration/Setup menu 6 Do one of the following, based on your configuration: • For a standalone switch, enter the IP address of the switch in the In-Band Switch IP Address field. Note: If the In-Band Subnet Mask field does not already contain a value when you enter the IP address in the In-Band Switch IP Address field, the switch software provides an in-use default value for the In-Band Subnet Mask field, based on the class of the entered IP address.
Chapter 2 Installing Device Manager software Device Manager software is available on the Nortel Networks Services and Support Web site as a self-extracting executable file. This chapter provides instructions to install the Device Manager software in a Windows or UNIX environment. Accessing the Nortel Networks Web site To access the Nortel Networks Services and Support Web site: 1 Go to the following URL: www12.nortelnetworks.
Chapter 2 Installing Device Manager software • • 128 MB DRAM 240 MB space on the hard disk Downloading the Device Manager Windows software To obtain the Device Manager software from the Nortel Networks Web site: 1 Go to the following URL: http://www.nortelnetworks.com/support 2 Click on the product for which you want JDM. A page opens that displays all versions of that product line. 3 Click Software under the specific product you are working with. The software page opens.
Chapter 2 Installing Device Manager software 3 23 Double-click the jdm_xxx.exe file. Note: Always install a new DM application into a clean directory, and uninstall previous versions. A dm.ini file from a previous version of DM may be moved into this directory. An Install screen opens that has text running through the screen. Then a Nortel dialog box opens with a ribbon on the bottom showing the progress. Finally, the InstallAnywhere* Introduction dialog box opens (Figure 3).
Chapter 2 Installing Device Manager software Figure 4 License Agreement dialog box 5 Click I accept the terms of the license agreement as shown in Figure 4. 6 Click Next. The Choose Install Set dialog box opens (Figure 5).
Chapter 2 Installing Device Manager software 7 25 Do one of the following: — Select Typical installation to install the common set features, as well as online help. — Select Minimal installation to select features to install (recommended for those with limited disk space). — Select Help to install only the online help. — Select Custom installation to customize the features prior to installation. 8 Click Next. The Choose Install Folder dialog box opens (Figure 6).
Chapter 2 Installing Device Manager software Figure 7 Choose Shortcut Folder dialog box 11 Select your shortcut path(s). 12 Click Next. The Pre-Installation Summary dialog box opens (Figure 8).
Chapter 2 Installing Device Manager software 27 13 Verify the folder, shortcut(s), and disk space required to install the software. Use the Previous button to return to the appropriate dialog box to make changes. 14 Click Install. The installation process begins (Figure 9). Figure 9 Installing Java Device Manager dialog box When the installation is complete, the Install Complete dialog box opens (Figure 10).
Chapter 2 Installing Device Manager software Figure 10 Install Complete dialog box 15 Click Done to exit the installation. Device Manager is now completely installed on your machine. UNIX installation The minimum system requirements for installing Device Manager in a UNIX SPARC* workstation running the Sun* Solaris* 2.6.
Chapter 2 Installing Device Manager software 29 — 32 MB DRAM Installing the Device Manager software in a UNIX environment requires two or three steps, depending on the specific platform: 1 In a Solaris environment, install Solaris patches (next). 2 In both environments, install the Java Runtime Environment (JRE): • • 3 For a Solaris environment, the JRE is available on the Nortel Networks Services and Support Web site. For an HP-UX environment, go to the HP Web site to obtain the JRE.
Chapter 2 Installing Device Manager software 1 Use the uname -a command to determine the version of SunOS/Solaris that is installed on your workstation. Table 1 lists the patch file archive name for each version of Solaris. Table 1 Solaris patch files SunOS/Solaris version Patch file name 5.6/2.6 jre131_sol56_patchBundle.tar 5.7/2.7 jre131_sol57_patchBundle.tar 5.8/2.8 jre131_sol58_patchBundle.
Chapter 2 Installing Device Manager software 6 31 Change the user to root and run the script by entering: su root ./pinst -cj 7 The patch installation can take up to several hours to complete, during which time, your system should be in a quiet state with a minimum of activity.
Chapter 2 Installing Device Manager software 2 Make the file executable by entering: chmod a+x /tmp/j2re-1_3_1_03-solsparc.sh 3 Change the working directory to /usr by entering: cd /usr You will install the JRE software to this directory. 4 You may need to be the root user to run the JRE installation. To change the user to root enter: su root 5 Execute the script file by entering: /tmp/j2re-1_3_1_03-solsparc.sh The script installs the JRE into the subdirectory named j2re1_3_1_03.
Chapter 2 Installing Device Manager software 33 Downloading the Device Manager UNIX software 1 Go to the following URL: http://www.nortelnetworks.com/support 2 Click on the product for which you want JDM. A page opens that displays all versions of that product line. 3 Click Software under the specific product you are working with. The software page opens. 4 Click the Java Device Manager version you want. The Software Detail Information page opens. 5 Click JDM for Unix-Solaris, HP-UX, IBM, AIX.
Chapter 2 Installing Device Manager software Figure 11 InstallAnywhere Introduction dialog box 3 Click Next to continue the installation process. The License Agreement dialog box opens (Figure 12).
Chapter 2 Installing Device Manager software 4 Click I accept the terms of the license agreement as shown in Figure 12. 5 Click Next. 35 The Choose Install Set dialog box opens (Figure 13). Figure 13 Choose Install Set dialog box 6 Do one of the following: — Select Typical installation to install the common set features, as well as online help. — Select Minimal installation to select features to install (recommended for those with limited disk space). — Select Help to install only the online help.
Chapter 2 Installing Device Manager software Figure 14 Choose Install Folder dialog box 8 Click Restore Default Folder or click Choose to select the storage path. 9 Click Next. The Pre-Installation Summary dialog box opens (Figure 15).
Chapter 2 Installing Device Manager software 37 10 Verify the folder, shortcut(s), and disk space required to install the software. Use the Previous button to return to the appropriate dialog box to make changes. 11 Click Install. The installation process begins (Figure 16). Figure 16 Installing Java Device Manager dialog box When the installation is complete, the Install Complete dialog box opens (Figure 17).
Chapter 2 Installing Device Manager software Figure 17 Install Complete dialog box 12 Click Done to exit the installation. Device Manager is now completely installed on your machine.
Chapter 3 Device Manager basics This chapter describes basic procedures for using the Device Manager software.
Chapter 3 Device Manager basics Note: On startup, Device Manager performs a DNS lookup for the machine on which it is running. If the DNS lookup is slow or fails, the initial Device Manager window may take up to 30 seconds to open. Figure 18 Device Manager window Setting the Device Manager properties Device Manager communicates with the BayStack 380-24F Gigabit Switch using Simple Network Management Protocol (SNMP).
Chapter 3 Device Manager basics 41 Figure 19 Properties dialog box 2 Type information and select check boxes. 3 Click OK. Table 2 describes items in the Properties dialog box. Table 2 Properties dialog box items Area Item Description Polling Status Interval Interval at which statistics and status information are gathered (default is 300 seconds). (If traps, Status Interval) Interval at which statistics and status information are gathered when traps are enabled (default is 300 seconds).
Chapter 3 Device Manager basics Table 2 Properties dialog box items (continued) Area Item Description SNMP Retry Count Number of times Device Manager retransmits polling information. Timeout Length of each retry of each polling waiting period. When accessing the device through a slow link, you may want to increase the timeout interval and then change the Retransmission Strategy to superlinear. Trace Enables (checked) or disables (not checked) SNMP tracing.
Chapter 3 Device Manager basics 43 To display the device view: 1 Do one of the following: • • • Choose Device > Open. Choose Device > Open Last, and select an IP address from the list. Click the folder icon in the Device Manager window. • Press [Ctrl] + O. The Open Device dialog box opens (Figure 20). Figure 20 Open Device dialog box Table 4 describes the items in the Open Device dialog box.
Chapter 3 Device Manager basics Table 4 Open Device dialog box items (continued) Item Description User Name Specifies a user name. Authentication Protocol Specifies authentication protocol. Authentication Password Specifies an authentication password. Privacy Protocol Specifies a privacy protocol. Privacy Password Specifies a privacy password. 2 In the Device Name text box, type the DNS name or IP address of the device.
Chapter 3 Device Manager basics 45 Device Manager window The Device Manager window (Figure 22) has the following parts: • • • • Menu bar Toolbar Device view Status bar Figure 22 Parts of the Device Manager window Menu bar Tool bar Device view Status bar Menu bar Use the menu bar to set up and operate Device Manager (Table 5). Table 5 Menu bar commands Command Description Device Opens the Open Device dialog box.
Chapter 3 Device Manager basics Toolbar The toolbar contains buttons that provide quick access to commonly used commands and some additional actions (Table 6). Table 6 Toolbar buttons Button Name Description Menu bar equivalent Open Device Opens the Open Device dialog box. Device > Open Refresh Device Refreshes the device view Status information. Device > Refresh Status Telnet Opens a Telnet session. Device > Telnet Trap Log Opens the trap log.
Chapter 3 Device Manager basics 47 Device view The device view (Figure 23) allows you to determine at a glance the operating status of the various units and ports in your hardware configuration. You also use the device view to perform management tasks on specific objects.
Chapter 3 Device Manager basics Selecting multiple objects To select multiple objects of the same type (such as ports or switches of the same type): Do one of the following: • For a block of contiguous ports, drag to select the group of ports. To select all the ports in a switch: Choose Edit > Select > Ports. LEDs and ports The color of LEDs in the device view is the same as the colors of the LEDs on the physical switch. However, the device view does not show blinking activity of the LEDs.
Chapter 3 Device Manager basics 49 The ports on the device view are color coded to show port status. Table 7 shows the status assigned to each color. Table 7 Port color codes Color Description Green Port is operating. Red Port has been manually disabled. Orange Port has no link. Light blue Port is in standby mode. Dark blue Port is being tested. Gray Port is unmanageable. Purple Loopback Mode.
Chapter 3 Device Manager basics Shortcut menus Each object in the device view has a shortcut menu that opens when you right-click a selected object. The switch shortcut menu (Figure 25) provides access to basic hardware information about the switch and to the graphing dialog boxes for the switch. Figure 25 Shortcut menu Table 8 describes the commands on the switch unit shortcut menu.
Chapter 3 Device Manager basics 51 Table 9 Port shortcut menu commands Command Description Edit Opens a dialog box that allows you to set operating parameters for the port. Graph Opens a dialog box that displays statistics for the port and allows you to display the statistics as a graph. Enable Administratively brings a port up. Disable Administratively shuts down a port. The color of the port changes to red in the device view.
Chapter 3 Device Manager basics Table 10 Device Manager buttons (continued) Button Name Description Stop Stops the current action (compiling, saving, and so forth). If you are updating or compiling a large data table, the Refresh button changes to a Stop button while this action is taking place. Clicking the Stop button interrupts the polling process. Export Data Exports information to a file you specify. You can then import this file into a text editor or spreadsheet for further analysis.
Chapter 3 Device Manager basics 53 Working with statistics and graphs Device Manager collects a wide range of statistics for each switch and each port. You can view and graph statistics for a single object or multiple objects. For information about the statistics tracked for the switch and ports, refer to Using the BayStack 380-24F Gigabit Switch. This section describes the types of statistics and graphs available, the graph dialog boxes, and the procedure for creating a graph.
Chapter 3 Device Manager basics Figure 27 Line graph Figure 28 Area graph 214392-A
Chapter 3 Device Manager basics 55 Figure 29 Bar graph Figure 30 Pie graph Getting Started with the BayStack 380-24F Gigabit Switch Management Software
Chapter 3 Device Manager basics Statistics for single and multiple objects Statistics for a selected object or objects are displayed in the statistics dialog box. The dialog box for a single object shows all six types of statistics for each counter (Figure 31). Figure 31 Interface statistics for a single port The statistics dialog box for multiple objects shows a single type of statistics (Table 11) for the selected objects. For example, Figure 32 shows LastValue statistics for the selected ports.
Chapter 3 Device Manager basics 57 To change the type of statistics displayed, select a different type from the show list at the bottom of the dialog box. The statistics are updated based on the poll interval shown at the bottom of the dialog box. You can select a different polling interval. Buttons for bar, pie, and line graphs are located at the bottom of a statistics dialog box. See the next section, “Viewing statistics as graphs,” for instructions to use these buttons.
Chapter 3 Device Manager basics Figure 33 Statistics dialog box for a port 3 Select a tab for the group of statistics you want to view. 4 On the displayed data table, drag to select the cells you want to graph. (They must be in the same row or column.) 5 Click one of the graph buttons at the bottom of the dialog box (see “Types of graphs” on page 53). A graph dialog box opens for the selected graph type. 6 214392-A To print a copy of the graph, click Print.
Chapter 3 Device Manager basics 59 Buttons at the top of the graph dialog boxes for line, area, and bar graphs allow you to change the orientation of the graph, change the scale, or change the graph type. Table 12 describes the buttons in the graph dialog boxes. Table 12 Graph dialog box buttons Button Name Description Stacked “Stacks” data quantities instead of displaying them side-by-side. Horizontal Rotates the graph 90 degrees.
Chapter 3 Device Manager basics Telneting to a switch From Device Manager, you can initiate a Telnet session to the console interface for the switch you are currently accessing. To Telnet to a switch: Do one of the following: • • From the Device Manager main menu, choose Device > Telnet. On the toolbar, click the Telnet button. A Telnet window to the switch opens. Trap log You can configure a BayStack 380-24F Gigabit Switch to send SNMP generic traps.
Chapter 3 Device Manager basics 61 By default, traps are sent in SNMP V2c format. However, if you are using an older network management system (NMS), one that supports only SNMP V1 traps (HP OpenView), you can specify that the traps be sent in V1 format. Management stations operating with Device Manager are automatically added to trap receivers. For more information about traps and trap receivers, refer to Using the BayStack 380-24F Gigabit Switch.
Chapter 3 Device Manager basics 214392-A
Chapter 4 Web management interface basics A BayStack 380-24F Gigabit Switch includes a Web management interface that lets you monitor your switch through a World Wide Web browser from anywhere on the network. The Web interface provides some of the more popular monitoring and configuration features of the Device Manager software. This chapter provides an overview of the Web management interface and its navigation features.
Chapter 4 Web management interface basics For instructions to set the IP address of the switch, refer to “Setting the switch IP parameters” on page 18. Access to the Web management interface must also be enabled for the switch (the default setting) using the console interface. For information about enabling Web access, refer to Using the BayStack 380-24F Gigabit Switch.
Chapter 4 Web management interface basics 65 Figure 34 System Information home page Network security does not yet exist the first time you access the Web management interface. As the system administrator, you must create access parameters and passwords. For more information about setting access parameters and system passwords, refer to “Setting up security” on page 70. 3 If passwords have already been set, the login page opens (Figure 35).
Chapter 4 Web management interface basics 4 In the Username text box, type RO for read-only access or RW for read-write access. 5 In the Password text box, type your password. 6 Click Log On. The System Information home page opens. With Web access enabled, the switch can support up to four concurrent Web page users. Two pre-defined user levels are available, and each user level has a corresponding user name and password.
Chapter 4 Web management interface basics 67 Web page layout All the Web management pages for the BayStack 380-24F Gigabit Switch have a common layout. Each is divided into two sections: the menu and the content area. All Web pages are optimized for an 800 x 600 pixel screen size. Menu The menu (Figure 36) is the same for all pages. It contains a list of seven main headings. Figure 36 Menu The first six headings provide options for viewing and configuring switch parameters.
Chapter 4 Web management interface basics Table 15 Menu headings and options 214392-A Heading Option Summary Switch Information Switch View Configuration IP System SNMPv1 SNMPv3 SNMP Trap MAC Address Table Find MAC Address Port Management High Speed Flow Control Software Download Configuration File Console/Comm Port Fault RMON Threshold RMON Event Log System Log Statistic Port Interface Ethernet Errors Transparent Bridging RMON Ethernet RMON History Application Port Mirroring VLAN Spanning
Chapter 4 Web management interface basics 69 Content area The content area displays tables of information with buttons that you use to configure and monitor the switch. Some tables may be too big to fit the displayed page area. In these cases, use the scroll bars at the side and bottom to view the entire table. Icons Some pages contain icons that allow you to modify information in a statistical table or to display statistics in chart format. Table 16 describes the icons.
Chapter 4 Web management interface basics Setting up security To set passwords and RADIUS (Remote Authentication Dial In User Service) authentication settings for the for the switch, use the Security pages. These pages allow you to create or modify the passwords of a switch, and allow you to set the security parameters for remote dial access users. Note: Nortel Networks recommends that when you install the switch, you set the initial system passwords using the console interface.
Chapter 4 Web management interface basics 71 Setting console, Telnet, and Web passwords 1 From the main menu, select Administration > Security. 2 On the Security page list, click Console, Telnet, or Web. The selected password management page opens (Figure 37). Note: The title of the page indicates which type of access you are setting the password for. In Figure 37, the network administrator selected Administration > Security > Console.
Chapter 4 Web management interface basics Setting remote dial-in access security To set the parameters for remote dial-in access security: 1 From the main menu, select Administration > Security > Radius. The Radius management page opens (Figure 38). Figure 38 Radius management page 214392-A 2 Type the IP addresses of the primary and secondary RADIUS (Remote Authentication Dial In User Services) servers. 3 Type the number of the user datagram protocol (UDP) port for the RADIUS server.
Index A Cumulative statistics 53 AbsoluteValue statistics 53 customer support 16 access levels 20, 42, 66 Actions menu 45 D Alarm Manager button 46 data, exporting 57 Area Chart button 59 default access community strings 42 area graph example 54 Device Manager installing on UNIX 28 installing on Windows 21 requirements 17 setting properties 40 starting 39 summary 17 Average statistics 53 B Bar Chart button 59 bar graph example 55 blinking LEDs 48 buttons dialog boxes 51 toolbar 46 C Devic
Index G Log Scale button 59 login window 65 graph creating 57 modifying 59 M Graph command 50, 51 Main Menu, console 19 graph dialog box 58 Max Traps in Log field 42 Graph menu 45 Maximum statistics 53 Graph Selected button 46, 57 menu bar, Device Manager 45 graph types 53 menu, Web 67 H menus.
Index pie graph example 55 polling interval 57 S polling waiting period 42 shortcut menus port 50 switch unit 50 port color legend 49 single object, selecting 47 port shortcut menu 50 SNMP tracing 42 ports color-coded 49 disabled 49 selecting 48 SNMP traps 60 Print button 51 Solaris patches, installing 30 product support 16 Stacked button 59 Properties dialog box 40 standalone switch, setting IP parameters 20 publications hard copy 15 related 15 standby port, color 49 polling interval, set
Index Telnet button 46, 60 Web management interface requirements 63 Telnet passwords 70 Web management options 67 Telnet session 45, 46, 60 Web passwords 70 tested port, color 49 Web site, Services and Support 21 text conventions 14 window, Device Manager 40, 45 Timeout parameter 42 Windows installation for Device Manager 21 timeout, setting 42 Write Community parameter 43 toolbar, Device Manager 46 Write Community, SNMP 44 Trace parameter 42 trap log 60 Trap Log button 46 Trap Port par
