002rp Server Hardware Installation CallPilot Release 4.0 Document Number: 555-7101-205 Document Version: Standard 1.
Standard 1.07 Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks.
October 2006 CRYSTAL REPORTS is a trademark of Seagate Software Inc. EUDORA is a trademark of Qualcomm. eTrust and InoculateIT are trademarks of Computer Associates Think Inc. DIRECTX, EXCHANGE.NET, FRONTPAGE, INTERNET EXPLORER, LINKEXCHANGE, MICROSOFT, MICROSOFT EXCHANGE SERVER, MS-DOS, NETMEETING, OUTLOOK, POWERPOINT, VISUAL STUDIO, WINDOWS, WINDOWS MEDIA, and WINDOWS NT are trademarks of Microsoft Corporation. GROUPWISE and NOVELL are trademarks of Novell Inc. LOGITECH is a trademark of Logitech, Inc.
Standard 1.07 WINZIP is a trademark of Nico Mark Computing, Inc. XEON is a trademark of Intel, Inc. All other trademarks and registered trademarks are the property of their respective owners.
October 2006 があります。この場合には使用者が適切な対策を取るように要求されることがあ ります。 This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may occur, in which case, the user may be required to take corrective action.
Standard 1.
Publication history October 2006 CallPilot 4.0, Standard 1.07 of CallPilot Installation and Configuration, 1002rp Server Hardware Installation is issued for general release. September 2006 CallPilot 4.0, Standard 1.06 of CallPilot Installation and Configuration, 1002rp Server Hardware Installation is up-issued. February 2006 CallPilot 4.0, Standard 1.05 of CallPilot Installation and Configuration, 1002rp Server Hardware Installation is issued for general release. January 2006 CallPilot 4.
Publication history October 2002 8 Standard 1.07 Standard 1.0 of CallPilot Installation and Configuration, 1002rp Server Hardware Installation is issued for general release.
Task List To unpack the equipment................................................................ 37 To remove the front bezel ............................................................... 40 To remove the server cover ............................................................ 41 To inspect the server interior........................................................... 42 To replace the front bezel after installation is complete .................. 44 To install the power supply module ...................
Task List 10 Standard 1.
Contents 1 How to get Help 13 2 1002rp server description 15 Server features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slot assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supported peripheral devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents A Standard 1.
Chapter 1 How to get Help This section explains how to get help for Nortel products and services. Getting Help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: http://www.nortel.com/support This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products.
How to get Help Standard 1.07 Outside North America, go to the following Web site to obtain the phone number for your region: http://www.nortel.com/callus Getting Help from a specialist by using an Express Routing Code To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: http://www.nortel.
Chapter 2 1002rp server description In this chapter Server features 16 Slot assignments 21 Network connectivity 25 Network connectivity 25 Supported peripheral devices 30 Reference documents 31 1002rp Server Hardware Installation 15
1002rp server description Standard 1.07 Server features Introduction This section provides a general overview of the 1002rp server. Server dimensions and weight Height 320 mm (12.5 in.) Width 483 mm (19 in.) Depth (distance from front to back) without front bezel 495 mm (19.5 in.) with front bezel 533 mm (21 in.) Weight of fully loaded system 16 45.
October 2006 1002rp server description Environmental specifications Environmental condition Specification Operating temperature 10°C to 35°C (50°F to 95°F) Maximum rate of change must not exceed 10°C (50°F) per hour. Non-operating (storage) temperature -40°C to 70°C (-40°F to 158°F) Non-operating humidity 95%, non-condensing at 30°C (86°F) Altitude 1829 m (6000 ft) Electrostatic discharge 15 kV or more Acoustic noise 50 dBA in a typical office ambient temperature (18°C to 25°C [64.
1002rp server description Standard 1.07 Front panel features (front view without the front bezel) The front view of the 1002rp server chassis shows redundant dual fans to the left and the right of the status panel. The left drive bay holds six SCSI hard drives with hot-pluggable carriers. The media drive bay, located to the right, houses the CD-ROM, tape drive, and floppy disk drive.
October 2006 1002rp server description Rear panel diagram The following diagram shows the slot locations in the rear panel, and the power switch and power input for an AC server. The rest of the diagram is the same for AC or DC servers.
1002rp server description Standard 1.07 Overhead view of empty server showing PCI and ISA connectors The following diagram shows the location of the PCI, SBC, and ISA connectors inside the server. The view in the diagram is from the rear of the server. For slot assignments, see “Slot assignments” on page 21. You must be able to identify slot locations for later steps in the CallPilot installation.
October 2006 1002rp server description Slot assignments Introduction The slot assignment tables show the following: the physical location of boards inside the server, relative to other boards the order in which boards are installed (for example, board #1, 2, 3) how the boards are represented in some CallPilot Manager applications (such as the Maintenance Administration page) the maximum capacity for each switch connectivity Note: Your server can vary depending on what was ordered from Norte
1002rp server description Standard 1.
October 2006 1002rp server description Meridian 1*/ CallPilot-assigned Succession* Slot number board labela 1000 T1/SMDI Slot 13 (PCI Slot 5) BRD13 MPB16-4 #2 (optional) D/480JCT-2T1 Slot 14 (PCI Slot 6) BRD14 MPB16-4 #2 (optional) or MPB96 #2 (optional) MPB96 board #2 (optional) Slot 15 (PCI Slot 7) BRD15 MPB16-4 #2 (optional) D/480JCT-2T1 (optional) Slot 16 (PCI Slot 8) BRD16 MPB16-4 #2 (optional) D/480JCT-2T1 (optional) Slot 17 (PCI Slot 9) BRD17 MPB16-4 #2 (optional) or MPB96 #3 (o
1002rp server description Standard 1.07 a. On some CallPilot Manager screens, the CallPilot-assigned board label is displayed. This label corresponds to the slot number. For example, BRD12 refers to the board in slot 12. b. The SBC card includes two onboard NICs (for ELAN and CLAN) and an onboard video card. The NIC and monitor connectors are on the SBC faceplate.
October 2006 1002rp server description Network connectivity Introduction This section describes how the 1002rp server can be integrated into your network. The integration depends on the type of switch you are using. ATTENTION To secure the CallPilot server from unauthorized access, ensure that the CallPilot network is inside your organization’s firewall.
1002rp server description Standard 1.07 Sample network setup: Meridian 1 The following diagram shows a CallPilot server sample network setup with a Meridian 1 switch.
October 2006 1002rp server description Sample network setup: Succession 1000 The following diagram shows a CallPilot server network setup with a Succession 1000 system.
1002rp server description Standard 1.07 In the previous illustration, the telephony LAN (TLAN) provides IP connectivity between the Succession 1000 system and the i2004 Internet phonesets. The connection between the call server and media gateway can be point-to-point, or it can be through the LAN, if the system is installed in a distributed data network.
October 2006 1002rp server description Network requirements Appropriate networking equipment must be available for both the CLAN and ELAN. The CLAN and ELAN must be properly configured for correct CallPilot operation. To ensure correct configuration, Nortel recommends that you consult a network specialist. Remote access connectivity The RS-232 COM1 connector on the rear of the 1002rp server provides the connection to an external modem.
1002rp server description Standard 1.07 Supported peripheral devices Introduction This section identifies external devices that are supported by the 1002rp server. Device Description Modem A 56-Kbit/s external modem (NTRH9078) provides remote access to the 1002rp server. The modem connects to the RS-232 COM1 connector on the rear of the server.
October 2006 1002rp server description Reference documents CallPilot Customer Documentation Map Fundamentals CallPilot Fundamentals Guide (555-7101-010) Planning and Engineering Planning and Engineering Guide (555-7101-101) Network Planning Guide (555-7101-102) Data Networking for Voice over IP Guide (553-3001-160) Installation and Configuration Upgrade and Platform Migration Guide (555-7101-207) Installation and Configuration Task List Guide (555-7101-210) Server Installation Guides 201i Server Hardwa
1002rp server description 32 Standard 1.
Chapter 3 Preparing for installation In this chapter Installation overview 34 Unpacking the 1002rp server 37 Removing the front bezel and server cover 39 Inspecting the server interior 42 1002rp Server Hardware Installation 33
Preparing for installation Standard 1.07 Installation overview Introduction This section provides an overview of the steps required to install the 1002rp server and peripheral devices. Installation checklist The following checklist identifies the tasks that must be performed when installing the CallPilot server. For detailed instructions, see Chapter 5, “Installing the server.” When you are finished with the installation, continue with the Installation and Configuration Task List (555-7101-210).
October 2006 Preparing for installation Step Description Check 6 For a DC-powered server, set up the DC power source (see page 50). ❒ 7 Place the 1002rp server in the chosen location (see page 60). ❒ 8 Replace the front bezel (see page 44). ❒ 9 Set the DIP switches on the modem (see page 61). ❒ 10 Connect the 1002rp server and devices as follows: Connect the monitor, keyboard, and mouse (see page 65). ❒ Connect the modem (see page 61).
Preparing for installation Standard 1.07 Conventions for warnings You may encounter the following types of warnings in this guide. Do not ignore them. DANGER Risk of electric shock . Warns you of an immediate electrical hazard which, if not avoided, can result in shock, serious injury, or death. WARNING Risk of personal injury . Warns you of a situation in which you can be injured if instructions are not followed exactly as stated. CAUTION Risk of equipment damage .
October 2006 Preparing for installation Unpacking the 1002rp server Introduction Follow this procedure to unpack the server and peripherals. WARNING Risk of personal injury . The 1002rp CallPilot server weighs approximately 34 kg (75 lb) as shipped from manufacturing. To prevent personal injury, have someone help you to unpack and position the server.
Preparing for installation Standard 1.07 5 Save all packing materials and cartons in case you must return any equipment to the carrier. What’s next? Remove the server cover so that you can inspect the interior of the server. See “Removing the front bezel and server cover” on page 39.
October 2006 Preparing for installation Removing the front bezel and server cover Introduction To access the server interior, you must remove both the front bezel and the server cover. Two locked doors, located on the front of the server, cover the front panel, including the CD-ROM drive and tape drive. These doors are part of the front bezel. You must unlock the front bezel doors before you can remove the bezel.
Preparing for installation Standard 1.07 To remove the front bezel CAUTION Risk of equipment damage . Do not attempt to move or lift the server before removing the front bezel; the server can disengage from the bezel and fall. 1 Unlock and open the double doors of the front bezel. See A in the diagram below. 2 Firmly grasp the front bezel by the hand-holds on either side of the chassis, and pull the front bezel from the chassis.
October 2006 Preparing for installation To remove the server cover DANGER Risk of electric shock . High current inside the chassis can cause severe injury. CAUTION Risk of equipment damage . Take precautions to protect internal components. Electrostatic discharge (ESD) can render boards damaged or unusable. Wear an ESD wrist strap. 1 Remove the front bezel (see page 40). 2 Loosen the three thumbscrews at the rear of the top cover.
Preparing for installation Standard 1.07 Inspecting the server interior Introduction You should perform a visual inspection for loose components, foreign matter, or shipping damage inside the server. CAUTION Risk of equipment damage When working with interior components, use an ESD wrist strap to protect static-sensitive components. . To inspect the server interior 1 Carefully check all the cards to ensure they are fully seated on the baseboard.
October 2006 Preparing for installation IF THEN you are satisfied that the 1002rp server has arrived at your site undamaged replace the server cover and proceed with the hardware installation. See “Installation checklist” on page 34. Note: Do not reinstall the front bezel until the server is in its final location and the CallPilot installation is complete.
Preparing for installation Standard 1.07 To replace the front bezel after installation is complete When the CallPilot server installation is complete and the server is in its final location, replace the front bezel. 1 Align the front bezel with the ball studs located at each faceplate corner. See the diagram below: Clips inside front bezel G101734 2 Apply pressure evenly until the bezel snaps onto each ball stud. 3 Close and lock the double doors of the front bezel.
Chapter 4 Power supply installation In this chapter Safety precautions 46 Installing the second power supply module (AC or DC) 47 DC wire gauge tables 50 DC rack cabling 52 About the power distribution unit 55 Bringing power and ground into the PDU 57 1002rp Server Hardware Installation 45
Power supply installation Standard 1.07 Safety precautions Equipment handling guidelines External power equipment, such as an uninterruptible power supply (UPS), is usually very heavy. This equipment requires special handling procedures and additional personnel for unloading and installation. Be aware of weight distribution, and prevent the equipment room floor from being overly stressed.
October 2006 Power supply installation Installing the second power supply module (AC or DC) Introduction One power supply module is shipped installed. The second power supply module must be installed on-site. AC versus DC systems The power supply modules are similar in appearance for both AC and DC 1002rp servers. The procedures in this section apply to both AC and DC 1002rp servers.
Power supply installation Standard 1.
October 2006 Power supply installation To install the power supply module DANGER Risk of electric shock High current inside the chassis can cause severe injury. . The server is shipped with one power supply module installed in the bottom power supply bay. You must install the second power supply module, as described here: 1 Align the power supply module with the top power supply bay. 2 Slide the power supply module into the bay until the module is secured by its connector. Use some force, if necessary.
Power supply installation Standard 1.07 DC wire gauge tables Introduction The tables in this section specify the DC power feed wire requirements.
October 2006 Power supply installation Metric wire conversion AWG No. Industry standard nominal (sq mm) Resistance at 20 C (Ohm/100 m) 2 35 0.05 4 25 0.08 6 16 0.13 8 10 0.20 10 6 0.33 12 4 0.63 14 2.5 1.00 16 1.5 1.40 18 1 2.00 20 0.75 2.90 22 0.5 4.
Power supply installation Standard 1.07 DC rack cabling The following photograph shows typical rack power cabling: Note: The cables are marked with Red and Green tape. The cables with the Red tape connect to the Negative (-) Red side (on the left in the photograph), and the cables with the Green tape connect to the Positive (+) Green side (on the right in the photograph). The sides are identified on the power connections. The ground wire enters at the lower right and attaches to the ground lug.
October 2006 Power supply installation Main panel wiring diagram with product number. Rack power and grounding To ensure a complete power and grounding installation: In rackmount server installations, ensure the CallPilot server chassis and equipment racks are isolated from other foreign sources of ground. Acceptable isolation methods include: isolation pads, grommeted washers, chassis side rail strips, and non-conducting washers.
Power supply installation Standard 1.07 -48 V DC power distribution rationale 54 Minimum installation is one power distribution unit (PDU) with four 48 V DC branch circuits fused at 20 amperes. The customer must be able to shut off any branch to ensure every unit at the site continues to function properly. DC-powered configuration fits into this scheme as follows: Each PDU receives four branch circuits. Each server receives a feed from each PDU and a different branch circuit.
October 2006 Power supply installation About the power distribution unit Introduction A PDU is installed in a rack that has DC-powered servers. Power from the DC supply source enters the PDU and can then be distributed to one or more servers. A single PDU can supply DC power to four DC power supply modules. A server can have either one or two power supply modules installed. You can determine the number of PDUs to install in a rack by counting the number of power supply modules in each rack.
Power supply installation Standard 1.07 PDU terminal blocks and wiring diagram A PDU consists of eight terminal blocks within a metal enclosure. Before installing the PDU, connect the terminal blocks so that each output connector receives power from a separate -48 V dc branch circuit, as shown in the following diagram. Use AWG 10 wires for these connections.
October 2006 Power supply installation Bringing power and ground into the PDU Introduction Install BAT/BATRTN wires in pairs. Each pair of wires supplies voltages to a module through a power harness. The module harnesses are installed in the cabinet PDU and connected to the modules at the factory. See “About the power distribution unit” on page 55. To bring DC power and ground into the PDU 1 If you are using a conduit, terminate the 32 mm (1-1/4 in.) or 19 mm (3/4 in.
Power supply installation 58 Standard 1.
Chapter 5 Installing the server and connecting the peripheral devices In this chapter Installing the server 60 Preparing the modem 61 Connecting peripherals to the server 65 Connecting the server to the ELAN 68 Connecting the server to the CLAN (optional) 71 Installing the Nortel software feature dongle 73 Connecting the server to power 75 1002rp Server Hardware Installation 59
Installing the server and connecting the peripheral devices Standard 1.07 Installing the server Introduction Before you install the 1002rp server, ensure that the chosen location meets the requirements identified on the “Site inspection checklist” provided in the Installation and Configuration Task List (555-7101-210). To install the server Place the 1002rp server in its chosen location. If you are installing the server in a rack cabinet, follow the instructions that are provided with the slide rails.
October 2006 Installing the server and connecting the peripheral devices Preparing the modem Introduction You require a modem to support remote dial-up access to the CallPilot server. The modem also enables Nortel technical support to connect to your CallPilot server for troubleshooting purposes. Nortel connects to your server only when you request technical assistance.
Installing the server and connecting the peripheral devices Standard 1.07 Modem DIP switches Set the modem DIP switches before you connect the modem to the CallPilot server. Note: This section applies only to the U.S. Robotics 56-Kbit/s external Sportster modem. If your modem is different, refer to the documentation for your modem.
October 2006 Installing the server and connecting the peripheral devices To set the modem DIP switches Use a pair of tweezers or a small screwdriver to set the DIP switches as described in the Change to column of the following table: Note: ON is down. OFF is up. DIP switch Default setting Change to Function 1 OFF OFF Data Terminal Ready (DTR) override 2 3 4 5 OFF ON OFF ON OFF ON OFF ON ON: The modem ignores DTR (override).
Installing the server and connecting the peripheral devices DIP switch Default setting Change to Function 6 OFF OFF Carrier Detect (CD) override 7 OFF OFF ON ON OFF: The modem sends a CD signal when it connects with another modem; it drops the CD on disconnect. ON: CD is always ON (override). Power-on and ATZ reset software defaults 8 Standard 1.07 OFF: Loads Y or Y1 configuration from user-defined NVRAM. ON: Loads &F0-Generic template from read-only memory (ROM).
October 2006 Installing the server and connecting the peripheral devices Connecting peripherals to the server Rear panel connectors SBC card (slot 8) Slot 20 Slot 1 SBC card PS/2 Keyboard/ Mouse Parallel port ELAN connector COM1 Power switch Power input Monitor connector COM2 CLAN connector G101648 Note: The above diagram shows the power switch and power input for an AC server. The rest of the diagram is the same for AC or DC servers.
Installing the server and connecting the peripheral devices Standard 1.07 To connect the mouse, keyboard, and monitor to the server 1 Place the monitor, keyboard, and mouse in the same location as the server. 2 Plug the keyboard/mouse dual cable into the PS/2 connector on the SBC card faceplate (see “Rear panel connectors” on page 65). 3 Plug the keyboard and mouse into the appropriate connectors on the keyboard/mouse dual cable. 4 Plug the monitor into the monitor connector on the SBC card.
October 2006 Installing the server and connecting the peripheral devices 6 Ensure that a single-point ground reference is available for all the power outlets serving the CallPilot server and its peripherals. Before the CallPilot server installation, a qualified electrician must implement the single-point ground reference requirement between the power outlets of the CallPilot server and the power outlets of the switch.
Installing the server and connecting the peripheral devices Standard 1.07 Connecting the server to the ELAN Introduction ATTENTION This section applies only if the 1002rp server connects to a Meridian 1 switch or Succession 1000 system. Connect the CallPilot server to the Meridian 1 switch or Succession 1000 system using the ELAN. ATTENTION For important considerations about using the ELAN in your network, see the Planning and Engineering Guide (555-7101-101).
October 2006 Installing the server and connecting the peripheral devices 3 Record the MAC address on the Configuration Wizard worksheet that is provided in the Installation and Configuration Task List (555-7101-210). You need the MAC address to identify the ELAN when running the Configuration Wizard to configure the CallPilot server. 4 Connect an RJ-45 network cable from the ELAN hub to the ELAN connector on the server.
Installing the server and connecting the peripheral devices Standard 1.07 What’s next? 70 IF the server will THEN be connected to a CLAN continue with page 71. not be connected to a CLAN continue with installing the software feature dongle. See page 73.
October 2006 Installing the server and connecting the peripheral devices Connecting the server to the CLAN (optional) Introduction This section provides instructions to connect the server to the CLAN. Note: The CLAN is optional. However, a CLAN is required to support desktop and web messaging users. ATTENTION To comply with EMC radiation requirements, a Class A hub must be located 10 m (33 ft.) away from the 1002rp server. Shielded Ethernet cables must be used.
Installing the server and connecting the peripheral devices Standard 1.07 You need the MAC address to identify the CLAN when running the Configuration Wizard to configure the CallPilot server. Note: When connecting the optional CLAN, do not power up unless your antivirus programs and Nortel security updates are installed first. 4 Connect an RJ-45 network cable from the CLAN hub to the CLAN connector. What’s next? Continue with “Installing the Nortel software feature dongle” on page 73.
October 2006 Installing the server and connecting the peripheral devices Installing the Nortel software feature dongle Introduction The software feature key is a security device that stores the unique serial number of the server. The feature key is embedded in the Nortel software feature dongle, which plugs into the parallel port.
Installing the server and connecting the peripheral devices Standard 1.07 Requirements For installation, you require a Phillips No. 1 screwdriver. To install the software feature dongle 1 Ensure that there is no cable connected to the parallel port. Note: The parallel port is also known as the printer port or LPT1. It is located at the back of the server. See the diagram on page 65.
October 2006 Installing the server and connecting the peripheral devices Connecting the server to power Before you begin Ensure that proper power and grounding are available for all the power outlets serving the CallPilot server and its associated peripherals. Power for these devices must be wired and fused independently of all other receptacles, and referenced to the same ground as the PBX system.
Installing the server and connecting the peripheral devices Standard 1.07 Before you connect the server to the power source, review the following diagram to ensure that all peripheral hardware devices are in place.
October 2006 Installing the server and connecting the peripheral devices To connect the 1002rp AC server to power WARNING Risk of personal injury, risk of hardware failure . The power outlets used by the CallPilot server and its peripheral devices must be connected to the same single-point ground reference as the one used by the switch with MGate cards (NTRB18CA) connected to the CallPilot server. If this requirement is not met, power transients can cause personal injury, or hardware failure, or both.
Installing the server and connecting the peripheral devices Standard 1.07 2 Connect the other end of the DC power cable to the PDU. Use the supplied clips and screws to secure the plugs. The following photograph shows the keyed plug of the DC power cable. This plug connects to the PDU: Note: If you are not using a Nortel-supplied PDU, have a qualified electrician connect the cable appropriately to your DC power plant.
Appendix A EMC emission level protection for the 1002rp Server To lower the EMC emission level, ferrite cores are installed with one loop (see diagram below) on the following external cables: Ferrite Core (TDK and part number ZCAT3035-1330) — for the triple DS30X I/O cable (Nortel and part number NTRH2014), at each end of the cable Ferrite Core (TDK and part number ZCAT1325-0530) — for the modem power supply cable, at each end of the cable Ferrite Core (Fair Rite and part number 0431164181) — f
EMC emission level protection for the 1002rp Server Standard 1.07 Ferrites secured to an external cable The ferrites are secured to the appropriate cable with plastic enclosure clips. Ty wraps are added to the cable loop.
Index Numerics 703t server environmental specifications 17 A adapter software feature key, illustration 73 alarm board 18 C checklist installation 34 CLAN media access control address 71 connecting peripherals to the server 65 connecting the server 75 connectivity Ethernet 28 remote 29 copyright 2 Customer LAN see CLAN 71 D DC power 54 DC power and ground 57 DC power input 56 DC wire gauge tables 50 devices, peripheral 1002rp Server Hardware Installation Ethernet hub 30 keyboard 30 modem 30 monitor 30 m
Index F fax modem illustration 62 required equipment 61 features server 16 features, front panel diagram 18 front bezel 40 G grounding guidelines 50 I illustration modem 62 software feature key adapter 73 TLAN 27 inspecting server interior 42 installation checklist 34 IRQ mapping table 25 K keyboard connecting to the server 66 description 30 keylock 73 M M1 and CallPilot server network diagram 26 Metric wire conversion 51 modem connecting to the server 66 description 30 82 Standard 1.
October 2006 power distribution unit See PDU power guidelines 50 power supply bringing power and ground into the PDU 57 DC wire gauge tables 50 grounding guidelines 50 Metric wire conversion 51 module installation 49 module location 47 overview 47 PDU 55 power distribution rationale 54 rack power and grounding 53 protocols, supported network 28 R rack power and grounding 53 regulatory information 2 remote access connectivity 29 removing front bezel 40 server cover 41 replacing server cover 43 Index slo
Index 84 Standard 1.
1002rp Server Hardware Installation CallPilot Release 4.0 Document Number: 555-7101-205 Document Version: Standard 1.07 October 2006 All Rights Reserved. To provide feedback or report a problem in this document, go to www.nortel.com/documentfeedback. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.
