201i Server Hardware Installation CallPilot Release 4.0 Document Number: 555-7101-220 Document Version: Standard 1.
Standard 1.07 Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks.
November 2006 CRYSTAL REPORTS is a trademark of Seagate Software Inc. EUDORA and QUALCOMM are trademarks of Qualcomm, Inc. ETRUST and INOCULATEIT are trademarks of Computer Associates Think Inc. DIRECTX, EXCHANGE.NET, FRONTPAGE, INTERNET EXPLORER, LINKEXCHANGE, MICROSOFT, MICROSOFT EXCHANGE SERVER, MS-DOS, NETMEETING, OUTLOOK, POWERPOINT, VISUAL STUDIO, WINDOWS, WINDOWS MEDIA, WINDOWS NT, and WINDOWS SERVER are trademarks of Microsoft Corporation. GROUPWISE and NOVELL are trademarks of Novell Inc.
Standard 1.07 SONY is a trademark of Sony Corporation. SYBASE is a trademark of Sybase, Inc. TEAC is a trademark of TEAC Corporation. US ROBOTICS, the US ROBOTICS logo, and SPORTSTER are trademarks of US Robotics. WINZIP is a trademark of Nico Mark Computing, Inc. XEON is a trademark of Intel, Inc. All other trademarks and registered trademarks are the property of their respective owners.
Publication history November 2006 Standard 1.07 of 201i Server Hardware Installation is released for CallPilot 4.0 general availability. October 2006 Standard 1.06 of 201i Server Hardware Installation is released for CallPilot 4.0 general availability. October 2006 Standard 1.05 of 201i Server Hardware Installation is released for CallPilot 4.0 general availability. September 2006 Standard 1.04 of 201i Server Hardware Installation is up-issued for CallPilot 4.0. July 2006 Standard 1.
Publication history September 2002 6 Standard 1.07 Standard 1.0 of CallPilot Installation and Configuration, Part 2: 201i Server Hardware Installation is released for CallPilot 2.0 general availability.
November 2006 Publication history .
Publication history 8 Standard 1.
Task List To unpack the 201i server............................................................... 41 To prepare the 201i server for installation in a Meridian 1 switch ... 52 To position the 201i server on the switch shelf ............................... 56 To remove the backplane cables .................................................... 59 To install the NTRH3501 backplane cable ...................................... 63 To install the SCSI cables for Meridian 1 ........................................
Task List 10 Standard 1.
Contents 1 How to get help 13 2 About the 201i server 15 201i server description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Network connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Peripheral connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3 Preparing for installation 35 Installation overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 6 Standard 1.07 Installing the 201i server in the Succession 1000 system 95 Succession 1000 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Removing the Media Gateway or Media Gateway Expansion cover . . . . 104 Installing the 201i server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Installing the NTRH3502 SCSI cable for Succession 1000 . . . . . . . . . . .
Chapter 1 How to get help This section explains how to get help for Nortel products and services. Getting Help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: http://www.nortel.com/support This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products.
How to get help Standard 1.07 Outside North America, go to the following Web site to obtain the phone number for your region: http://www.nortel.com/callus Getting Help from a specialist by using an Express Routing Code To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: http://www.nortel.
Chapter 2 About the 201i server In this chapter 201i server description 16 Network connectivity 24 Peripheral connectivity 31 201i Server Hardware Installation 15
About the 201i server Standard 1.07 201i server description Introduction The 201i server is a flexible multimedia telephony server designed to integrate with Nortel Meridian 1* and Succession* 1000 products. The 201i server occupies two slots of a Meridian 1 shelf or Succession 1000 Media Gateway or Media Gateway Expansion. When the server is locked into position, its connectors attach to the backplane, which provides power and communications links.
November 2006 About the 201i server Two Ethernet controllers on the 201i server motherboard provide Ethernet capability. These controllers provide the network interfaces for both the embedded LAN (ELAN) and customer LAN (CLAN). The connections to the ELAN and CLAN are established by using the multi I/O cable described on page 28. Note: The secondary backplane connector connects the 201i server to the second slot on the shelf, thereby providing access to the voice channels provided by that slot.
About the 201i server Standard 1.07 The following diagram shows the 201i server components:. Heat sink Keyboard connector Mouse connector Monitor connector Faceplate Hard drive power cable Hard drive data cable Secondary backplane connector pin Secondary backplane connector 3.
November 2006 About the 201i server Faceplate The following diagram shows the 201i server faceplate.
About the 201i server Standard 1.07 The following table describes each faceplate feature: Faceplate feature Description Mouse connector The mouse connector is a standard PS/2 connector and is hot-pluggable. Lock latches Lock latches at the top and bottom of the faceplate secure the server to the backplane of the Meridian 1 switch or the backplane of the Succession 1000 Media Gateway or Media Gateway Expansion.
November 2006 Faceplate feature MPC card status LEDs (continued) About the 201i server Description On, then off: The MPC card has been successfully powered down. It is safe to remove the card. Note: For instructions on powering up or powering down the MPC card, see “Starting and stopping components” in the CallPilot 201i Server Maintenance and Diagnostics guide. MPC card ejector buttons There is one ejector button for each MPC card slot.
About the 201i server Faceplate feature Standard 1.07 Description Network and drive The E and C LEDs indicate the presence of network activity LEDs activity for both the ELAN and CLAN interfaces (labeled as E, C, I, and S) (respectively). When they are lit, they indicate that the interfaces are properly attached to their respective hubs. When the LEDs are blinking, there is network activity. When the I and S LEDs are lit, it means that the IDE hard drive and SCSI device are being accessed.
November 2006 About the 201i server Absolute RH 20% to 80% RH (noncondensing) Long-term storage RH 5% to 95% RH [at –40°C (-40°F) to 70°C (158°F) respectively] (noncondensing) 201i Server Hardware Installation 23
About the 201i server Standard 1.07 Network connectivity Introduction This section shows how CallPilot and the Meridian 1 or Succession 1000 system are integrated into your network. It also describes what is required in the network for correct CallPilot operation. ATTENTION To secure the CallPilot server from unauthorized access, ensure that the CallPilot network is inside your organization’s firewall.
November 2006 About the 201i server Web-enabled administrative PC Desktop client PC Desktop client PC Telephony LAN/Customer LAN (10/100BaseT or 100BaseT) Modem Web-enabled administrative PC Switch Router or Ethernet switch (optional) Laptop 201i CallPilot server Embedded LAN (10BaseT) G101631 201i Server Hardware Installation 25
About the 201i server Standard 1.
November 2006 About the 201i server In the illustration on page 26, the telephony LAN (TLAN) provides IP connectivity between the Succession 1000 system and the i2004 Internet phonesets. The connection between the Call Server and Media Gateway can be point-to-point, or it can be through the LAN, if the system is installed in a distributed data network.
About the 201i server Standard 1.07 Network requirements Appropriate networking equipment must be available for both the CLAN and ELAN. The CLAN and ELAN must be properly configured for correct CallPilot operation. To ensure correct configuration, Nortel recommends that you consult a network specialist. ATTENTION For important considerations about using the ELAN in your network, see “About the ELAN” in the CallPilot Installation and Configuration Task List.
November 2006 About the 201i server The following table identifies the purpose of each connector on the NTRH09121 multi I/O cable. Note: Labels on the RJ-45 cables distinguish the CLAN and ELAN connectors. Connector type Purpose 50-pin amphenol This connector establishes the connection between the Meridian 1 or Succession 1000 Media Gateway or Media Gateway Expansion backplane and the ELAN hub, the CLAN hub, and the modem.
About the 201i server 30 Standard 1.07 Connector type Purpose RS-232 COM1 (male DB-9) This connector provides the connection to an external modem. The modem allows administrators and technical support personnel to administer the 201i server from a remote location.
November 2006 About the 201i server Peripheral connectivity Introduction Peripheral equipment is attached to the 201i server on the server faceplate. Faceplate connections ATTENTION Connections made to the faceplate (with the exceptions noted below) are temporary only, because you must remove the cabinet cover to make these connections. The system does not meet specifications for radiated EMI if you remove the cabinet cover.
About the 201i server Standard 1.07 MPC-8 card The MPC-8 card looks like a Type II PC card, and supports the multimedia telephony services on the 201i server. Four specially-designed card slots are available for the MPC-8. All are located on the 201i server faceplate. ATTENTION You cannot insert MPC-8 cards in Type II PC card slots, or Type II PC cards into MPC-8 card slots. They are not compatible. SCSI connections The SCSI connection is the only permanent faceplate connection.
November 2006 About the 201i server Note: The CD-ROM drive is not hot-pluggable. You must power off the server to connect or disconnect the drive. Tape drive (NTRH9038) An external SCSI tape drive is used to back up and restore data. The device connects to the server by an intermediate SCSI cable that connects to the SCSI connector on the faceplate. Since the tape drive is an external device, it requires an AC power source. Set the SCSI ID for the tape drive to 5.
About the 201i server Standard 1.07 Note: The mouse connector on the 201i faceplate is a PS/2 connector. If you plan to use a USB mouse with USB-to-PS/2 converter, you must also use the Nortel-supplied 101 mm (4-in) PS/2 extension cable (A0855616). Without the extension cable, the monitor connector partially blocks the mouse connector.
Chapter 3 Preparing for installation In this chapter Installation overview 36 Unpacking and inspecting the 201i server 41 Switch and network requirements 44 201i Server Hardware Installation 35
Preparing for installation Standard 1.07 Installation overview Introduction This section provides a high-level overview of the requirements and procedure for installing the 201i server. For a list of CallPilot documentation, see the document map on page 7. Before you begin Ensure that proper power and grounding are available for all the power outlets serving the CallPilot server and its associated peripherals.
November 2006 Preparing for installation Installation checklist The following checklist identifies the steps required to install the 201i server and peripheral devices. For more details, see Chapter 8, “Connecting peripheral devices to the 201i server.” WARNING Risk of personal injury and hardware failure .
Preparing for installation Standard 1.07 Step Description 2 Familiarize yourself with the “Switch and network requirements” on page 44 of this guide. ❒ 3 If you are installing the 201i server into a Meridian 1 tiered system, do the following: ❒ 4 Change the location of the secondary backplane (DS30X) connector on the 201i server (see page 50). Replace the existing backplane (tip and ring) cable on the Meridian 1 with the one supplied with the 201i server (NTRH3501) (see pages 58–64).
November 2006 Preparing for installation Step Description 6 Set the following: 7 8 SCSI IDs on the CD-ROM and tape drives (see pages 126 and 128) DIP switches on the CD-ROM drive (see page 126) device termination on the CD-ROM and tape drives (see page 130) Insert the 201i server into two consecutive slots inside the switch.
Preparing for installation Step Description 9 Connect the 201i server and devices as follows: Standard 1.07 Check Connect the monitor, keyboard, and mouse to the 201i server faceplate (see page 142). ❒ Connect the CD-ROM and tape drives to the intermediate SCSI cable (see page 144). ❒ Connect the multi I/O cable to the ELAN and CLAN network hubs (see page 153).
November 2006 Preparing for installation Unpacking and inspecting the 201i server Introduction This section describes how to: unpack the 201i server and peripherals inspect the 201i server for damage It also describes what to do if you determine that the 201i server is faulty.
Preparing for installation Standard 1.07 To inspect the 201i server for shipping damage Before proceeding with the installation, visually inspect the 201i server for any damage that might have occurred during shipping. Ensure also that the items in the following checklists are secure: Item Yes No Are all cables securely seated? hard drive power cable ❒ ❒ hard drive data cable ❒ ❒ Is the hard drive and bracket interface secure? See items 6 and 7 in the diagram on page 18.
November 2006 Preparing for installation What’s next? Review the “Switch and network requirements” on page 44.
Preparing for installation Standard 1.07 Switch and network requirements Introduction The information in this section will help you plan your 201i server installation. Meridian 1 or Succession 1000 slot requirements The 201i server occupies two physical and electrical slots.
November 2006 Preparing for installation Switch Slots Succession 1000 A pair of consecutive slots in any Media Gateway or Media Gateway Expansion. Note: The 201i server cannot be installed in slots 0 or 4, because these slots are dedicated to other cards. For more information about cards and slots, refer to the Succession 1000 Planning and Installation Guide (NTP 553-3023-210).
Preparing for installation Standard 1.07 If the LAN is to be networked with the 201i server, you need a network specialist to ensure proper configuration. ATTENTION For important considerations about using the ELAN in your network, see “About the ELAN” in the CallPilot Installation and Configuration Task List. What’s next? Install the 201i server in the Meridian 1 switch or Succession 1000 system.
Chapter 4 Installing the 201i server in a large Meridian 1 system In this chapter Overview 48 Repositioning the secondary backplane connector 50 Installing the 201i server in the large Meridian 1 switch 56 Removing the backplane (tip and ring) cables 58 Installing the NTRH3501 backplane cable 62 Installing the SCSI cables for Meridian 1 65 201i Server Hardware Installation 47
Installing the 201i server in a large Meridian 1 system Standard 1.07 Overview Introduction This section describes how to install the 201i server in a Meridian 1 switch. ATTENTION To install the 201i server in an Option 11C, go to page 72. For Option 11C Mini, go to page 85. For Succession 1000, go to page 95.
November 2006 Installing the 201i server in a large Meridian 1 system CAUTION Risk of equipment damage . ATTENTION The 201i server is shipped ready for installation into an Option 11C switch. Before you install the 201i server in a larger Meridian 1 switch (for example, Option 51C), you must move the secondary backplane (DS30X) connector to the correct position. A yellow warning label over the top lock latch on the 201i server prevents you from securing the 201i server in a slot.
Installing the 201i server in a large Meridian 1 system Standard 1.07 Repositioning the secondary backplane connector Introduction The secondary backplane (DS30X) connector on the 201i server connects the server to the second slot on the shelf, thereby providing access to the voice channels provided by that slot. CAUTION Risk of equipment damage . The 201i server ships ready for installation into an Option 11C or Option 11C Mini switch.
November 2006 Installing the 201i server in a large Meridian 1 system Secondary backplane connector description The secondary backplane connector is attached to the backplane edge of the 201i server. It consists of the following items: connector screws pin connector (with four pins) Two pairs of screw holes are provided for connecting the secondary backplane connector to the 201i server stiffening cage. The outside pair provides the Meridian 1 spacing.
Installing the 201i server in a large Meridian 1 system Standard 1.07 Required equipment To move the secondary backplane connector, you need a Phillips No. 1 screwdriver. A pair of needle-nosed pliers can also be helpful for removing the pin connector. To prepare the 201i server for installation in a Meridian 1 switch 1 Remove the secondary backplane pin connector. The pin connector has four pins. If necessary, use needle-nosed pliers to remove it.
November 2006 Installing the 201i server in a large Meridian 1 system See the following diagram: Screw location for Meridian 1 G101545 5 Replace the pin connector so the pins protrude through both connectors. Ensure that the connectors are correctly aligned as shown in the diagram below. CAUTION Risk of equipment damage . If the connectors are not correctly aligned when the pin connector is pressed into the socket, the pins can bend.
Installing the 201i server in a large Meridian 1 system Standard 1.
November 2006 Installing the 201i server in a large Meridian 1 system 6 Gently press the pin connector into the socket until it is fully seated. 7 Remove the yellow backplane warning label from the top lock latch on the 201i server. What’s next? Continue with “Installing the 201i server in the large Meridian 1 switch” on page 56.
Installing the 201i server in a large Meridian 1 system Standard 1.07 Installing the 201i server in the large Meridian 1 switch Introduction The 201i server occupies two slots. You can install the 201i server in slots 0 through 14. Ensure that both slots have electrical backplane connectivity. To position the 201i server on the switch shelf 1 Ensure that no cables are connected to the slots in which you are installing the 201i server.
November 2006 Installing the 201i server in a large Meridian 1 system What’s next? Continue with “Removing the backplane (tip and ring) cables” on page 58.
Installing the 201i server in a large Meridian 1 system Standard 1.07 Removing the backplane (tip and ring) cables Introduction You must remove the Meridian 1 backplane (tip and ring) cables that are associated with the slots occupied by the 201i server so that you can install the following cables: NTRH3501 backplane (tip and ring) cable The NTRH3501 cable offers more network throughput than the cable that is already installed on the Meridian 1.
November 2006 Installing the 201i server in a large Meridian 1 system To remove the backplane cables 1 Remove the I/O panel cover from the rear of the Meridian 1 switch. 2 Remove the protective plate from the rear of the Meridian 1 switch. G101547 3 Remove the existing backplane cable, including the I/O filter assembly (NT8D81xx) and mounting hardware for the left slot as follows: a. Remove the external cable attached to the outside of the I/O panel. b.
Installing the 201i server in a large Meridian 1 system ATTENTION Standard 1.07 If you attempt to pull the connector off without pressing the lock tab, you can pull the connector shroud off the backplane. If this happens, refer to the adjacent connectors for correct key positioning, and then replace the connector shroud. Remove the tie wraps where applicable to free the cable. c.
November 2006 Installing the 201i server in a large Meridian 1 system The following diagram shows an example using slots 3 and 4: C B A G101549 What’s next? Continue with “Installing the NTRH3501 backplane cable” on page 62.
Installing the 201i server in a large Meridian 1 system Standard 1.07 Installing the NTRH3501 backplane cable Introduction You must connect the backplane (tip and ring) cable supplied with the 201i server (NTRH3501) for 100Base-T Ethernet CLAN operation. This cable offers more network throughput than the cable you just removed from the Meridian 1. When installed, this cable completes the connection between the left slot, the I/O panel on the rear of the switch, and the multi I/O cable on the 201i server.
November 2006 Installing the 201i server in a large Meridian 1 system Before you begin Before you can install the NTRH3501 cable, you must remove the existing backplane cable from the back of the switch. See “Removing the backplane (tip and ring) cables” on page 58. To install the NTRH3501 backplane cable 1 Install and connect the NTRH3501 cable to the multi I/O cable as follows: a.
Installing the 201i server in a large Meridian 1 system Standard 1.07 See the following diagram: Backplane cable NTRH3501 Multi I/O cable NTRH0912 UP 1 A B C UP 2 UP 3 G101550 What’s next? Continue with “Installing the SCSI cables for Meridian 1” on page 65.
November 2006 Installing the 201i server in a large Meridian 1 system Installing the SCSI cables for Meridian 1 Introduction Before you can connect a CD-ROM or tape drive to the 201i server, you must install the SCSI cables. The SCSI cables route the SCSI connection away from the 201i server faceplate so that an external SCSI device can remain permanently connected. CAUTION Risk of equipment damage You must power off the 201i server before connecting or disconnecting SCSI cables. .
Installing the 201i server in a large Meridian 1 system Standard 1.07 The connector on the intermediate SCSI cable that attaches to the 201i server faceplate is a low-profile right-angle connector. This allows the cable to be attached with the Meridian 1 cabinet cover on.
November 2006 Installing the 201i server in a large Meridian 1 system In this diagram, the CD-ROM drive is the first device. The tape drive is the last device. 201i cabling Peripheral cabling Meridian 1 Optional 201i NTRH30AA NTRH9038 Tape drive NTRH1408 Rear I/O panel SCSI device cable NTRH3502 NTRH9105 CD-ROM drive NTRH1410 G101430 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
Installing the 201i server in a large Meridian 1 system Standard 1.07 To install the SCSI cables for Meridian 1 1 Thread the SCSI connector end of the NTRH1408 cable from the front of the Meridian 1 along the bottom of the shelf to either the left or the right access channel. 2 Leave the low-profile right-angle SCSI connector hanging for now. You will connect it later to the 201i server faceplate.
November 2006 Installing the 201i server in a large Meridian 1 system See the following diagram: Remove this cover Intermediate SCSI cable NTRH1408 Cable routed from front SCSI cable NTRH1410 G101551 Note: The backplane connectors for the right slot are not required and, therefore, are left vacant. 6 Thread the NTRH1410 cable through the shelves below and out through the bottom of the Meridian 1 tower.
Installing the 201i server in a large Meridian 1 system Standard 1.07 7 Replace the protective plate. 8 Replace the I/O panel cover. 9 Power up the shelf. What’s next? Prepare the modem, CD-ROM drive, and tape drive for connection to the 201i server. For instructions, see Chapter 7, “Preparing peripheral devices.
Chapter 5 Installing the 201i server in an Option 11C or Option 11C Mini In this chapter Installing the 201i server in the Option 11C or Option 11C Mini switch 72 Section A: Installing Option 11C cables 77 Installing the intermediate SCSI cable for Option 11C 78 Section B: Installing Option 11C Mini cables 85 Installing the NTRH3502 SCSI cable for Option 11C Mini 86 Installing cables on the back of the Option 11C Mini cabinet 92 201i Server Hardware Installation 71
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 Installing the 201i server in the Option 11C or Option 11C Mini switch Introduction The 201i server occupies physical and electrical slots. The 201i server must be installed in two peripheral equipment slots as follows: Switch Eligible slots Option 11C Slots 1 through 9 Note: Both of the server backplane connectors must be installed in slots 1 through 9 to receive proper power. Neither connector can reside in slot 10.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini See the following diagram: A C B G101559 2 Ensure that no cables are connected to the slots in which you are installing the 201i server. 3 Open the lock latches at the top and bottom of the 201i server faceplate. Note: When you open the top lock latch, it breaks the yellow backplane warning label, if the label has not been removed. The label is not relevant for Option 11C or Option 11C Mini.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 4 Slide the 201i server into an unoccupied pair of slots. Ensure that the 201i server is positioned correctly between the slots. Note: When correctly inserted in the Option 11C Mini, the top of the 201i server is on the left. See the following diagram: G101588b ATTENTION Do not push the 201i server into place against the backplane until you are ready to observe the startup cycle.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini What’s next? Continue with installing the cables.
Installing the 201i server in an Option 11C or Option 11C Mini 76 Standard 1.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini Section A: Installing Option 11C cables In this section Installing the intermediate SCSI cable for Option 11C 201i Server Hardware Installation 78 77
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 Installing the intermediate SCSI cable for Option 11C Introduction Before you can connect an external CD-ROM or tape drive to the 201i server, Option 11C requires an intermediate SCSI cable (NTRH1407). Note: If you are installing the 201i server in an Option 11C Mini, go to page 86. Cable description The connector on the NTRH1407 cable that attaches to the 201i server faceplate is a low-profile right-angle connector.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini Option 11C SCSI cable NTRH1407 201i server faceplate connector Drain wire SCSI connector Bracket assembly G101553 What the completed installation looks like The following diagram shows how the intermediate SCSI cable, CD-ROM drive, and tape drive are connected to the Option 11C. The CD-ROM drive is the first device. The tape drive is the last device.
Installing the 201i server in an Option 11C or Option 11C Mini 201i cabling Standard 1.07 Peripheral cabling Option 11C 201i NTRH30AA Optional NTRH9038 Tape drive NTRH1407 Bracket assembly Tape drive SCSI cable NTRH3502 NTRH9105 CD-ROM drive CD-ROM drive SCSI cable NTRH3502 G101434 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini To install the cable CAUTION Risk of equipment damage . You must power off the 201i server before connecting or disconnecting SCSI cables. 1 Attach the bracket assembly and cable as follows: a. Below the card cage, temporarily remove the hardware that secures cable connections to the Option 11C. b. Temporarily remove any cabling that may interfere with the installation of the intermediate SCSI cable bracket assembly.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 See the following diagram: A B C D Intermediate SCSI cable bracket assembly NTRH1407 G101554 2 Thread the cable up through the card cage. Note: When routing the SCSI cable through the card cage, ensure the second cable ferrite is placed halfway through the opening. 3 Connect the grounding braid on the intermediate SCSI cable to the card cage, and tighten the screw.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 4 Leave the low-profile right-angle SCSI connector loose for now. You will connect it later to the 201i server faceplate. Note: The following diagram shows what the connection looks like after the cable is connected: 201i server Intermediate SCSI cable NTRH1407 Position the second cable ferrite so that it is halfway through opening.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 5 Replace all cabling and hardware that you removed in step 1. 6 Restore any services that you took out of service in step 1. What’s next? Prepare the modem, CD-ROM drive, and tape drive for connection to the 201i server. For instructions, see Chapter 7, “Preparing peripheral devices.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini Section B: Installing Option 11C Mini cables In this section Installing the NTRH3502 SCSI cable for Option 11C Mini 86 Installing cables on the back of the Option 11C Mini cabinet 92 201i Server Hardware Installation 85
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 Installing the NTRH3502 SCSI cable for Option 11C Mini Introduction Before you can connect a CD-ROM or tape drive to the 201i server, you must install the NTRH3502 SCSI cable. The NTRH3502 SCSI cable routes the SCSI connection away from the 201i server faceplate so that an external SCSI device can remain permanently connected.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i cabling Peripheral cabling Option 11C Mini Optional 201i NTRH30AA NTRH9038 Tape drive Tape drive SCSI cable NTRH3502 NTRH9105 CD-ROM drive CD-ROM drive SCSI cable NTRH3502 SCSI adapter A0769312 G101595 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 To install the NTRH3502 SCSI cable CAUTION Risk of equipment damage . You must power off the 201i server before connecting or disconnecting SCSI cables. 1 If your Option 11C Mini is equipped with a Fiber Routing Guide, temporarily remove it. Note: For detailed instructions, refer to the Option 11C and Option 11C Mini Expansion Guide (NTP 553-3021-208).
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini See the following diagram: Inner SCSI bracket Note: After you remove the bracket, refasten the screws in their original locations inside the cabinet. G101587 3 Refasten the inner SCSI bracket screws in their original locations inside the cabinet. You will use the top screw later to fasten the NTRH3502 SCSI cable drain wire.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 SCSI cable installation to accommodate the Fiber Routing Guide Ferrites from EMC kit NTRH3503 Drain wire SCSI cable NTRH3502 G101590 6 If required, reinstall the Fiber Routing Guide. Note: For detailed instructions, refer to the Option 11C and Option 11C Mini Expansion Guide (NTP 553-3021-208).
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini See the following diagram: Fiber routing bracket Fiber routing spool Note: Ensure the fiber routing spool and bracket are correctly aligned before fastening them in place. G101591 7 Replace the cabinet cover. What’s next? Continue with “Installing cables on the back of the Option 11C Mini cabinet” on page 92.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 Installing cables on the back of the Option 11C Mini cabinet Introduction The following items connect to the back of the Option 11C Mini cabinet: multi I/O cable (NTRH0912) Option 11C Mini power cord with two ferrites You must connect the multi I/O cable first before connecting the power cord, because the power cord routes over the multi I/O cable connection.
November 2006 Installing the 201i server in an Option 11C or Option 11C Mini The following diagram shows how to secure the multi I/O cable connection: Velcro fastening strap A Pull to tighten the strap B C G101592 3 Attach the multi I/O cable drain wire to a screw on the cabinet. See the diagram in step 4. 4 Connect the power cord to the Option 11C Mini cabinet.
Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 See the following diagram: Drain wire G101593 What’s next? Prepare the modem, CD-ROM drive, and tape drive for connection to the 201i server. For instructions, see Chapter 7, “Preparing peripheral devices.
Chapter 6 Installing the 201i server in the Succession 1000 system In this chapter Succession 1000 description 96 Removing the Media Gateway or Media Gateway Expansion cover 104 Installing the 201i server 107 Installing the NTRH3502 SCSI cable for Succession 1000 110 Replacing the Media Gateway or Media Gateway Expansion cover 114 Connecting cables to the Succession 1000 system 117 201i Server Hardware Installation 95
Installing the 201i server in the Succession 1000 system Standard 1.07 Succession 1000 description Introduction The Succession 1000 system is an IP PBX that provides telephony and data capabilities over an IP network. The Succession 1000 system consists of the following major components: Call Server Media Gateway Media Gateway Expansion Call Server The Call Server provides telephony services and call processing.
November 2006 Installing the 201i server in the Succession 1000 system one AC power cord connector and On/Off switch The following diagram shows the Call Server: G101623 Media Gateway and Media Gateway Expansion The Media Gateway and Media Gateway Expansion provide the interface for analog or digital trunks, i2004 Internet phonesets, analog phonesets, and applications such as CallPilot. A Media Gateway Expansion can be connected to the Media Gateway to increase system capacity.
Installing the 201i server in the Succession 1000 system Standard 1.07 The following table identifies the Media Gateway and Media Gateway Expansion slots into which you can install the CallPilot 201i server: Unit The 201i server can be installed in Media Gateway Slots 1 and 2 Ineligible slots Slot 0 is dedicated to the SSC card. Slots 2 and 3 Slot 4 (includes slots 5 and 6) is not used. Media Gateway Expansion Slot 10 is a double-wide slot.
November 2006 Installing the 201i server in the Succession 1000 system Media Gateway and Media Gateway Expansion 1 Media Gateway and Media Gateway Expansion 2 Physical slot Logical slot Physical slot Logical slot 6 Not supported 6 Not supported Media Gateway Expansion Media Gateway Expansion 7 17 7 27 8 18 8 28 9 19 9 29 10 20 10 30 Media Gateway and Media Gateway Expansion 3 Media Gateway and Media Gateway Expansion 4 Physical slot Physical slot Logical slot Media Gateway
Installing the 201i server in the Succession 1000 system Standard 1.
November 2006 Installing the 201i server in the Succession 1000 system Connector Media Gateway Media Gateway Expansion One 10Base-T Ethernet connector that yes no DS30X and CE-MUX connectors for connecting the Media Gateway and Media Gateway Expansions together yes yes Power connector yes yes provides the ELAN interface to management software applications such as Optivity Telephony Manager and CallPilot accepts an industry-standard Medium Access Unit (MAU) The following diagram shows t
Installing the 201i server in the Succession 1000 system Standard 1.07 Note: Except for the back panel connectors, the Media Gateway Expansion is similar in external appearance to the Media Gateway. Succession 1000 software For the 201i server, the Succession 1000 system must be running Succession Release 3.00 (or later) software. The Media Gateways and Media Gateway Expansions are centrally configured from the Call Server. This allows for a single point of management.
November 2006 Installing the 201i server in the Succession 1000 system Succession 1000 documentation If you need to refer to the following Succession 1000 technical documents, they are stored on the Customer Documentation Library CD-ROM (NTLH80BA), provided with your Succession 1000 system: Succession 1000 Planning and Installation Guide (NTP 553-3023-210) Note: This guide is also provided in printed format with your Succession 1000 system.
Installing the 201i server in the Succession 1000 system Standard 1.07 Removing the Media Gateway or Media Gateway Expansion cover Introduction To access the interior of the Media Gateway or Media Gateway Expansion, you must remove the front bezel and inside front cover plate. To remove the front bezel and inside front cover plate WARNING Risk of eye injury . Nortel recommends that you operate the Media Gateway and Media Gateway Expansion with their front bezels installed.
November 2006 Installing the 201i server in the Succession 1000 system A B C G101620 a. Use a slot screwdriver to gently pry off the SUCCESSION label. b. Insert the screwdriver approximately 2 cm (0.75 in.) into the open slot, and then gently lift the screwdriver handle, thus applying downward pressure on the tab inside the bezel. At the same time, gently pull the bezel away from the chassis (approximately 2 cm [0.75 in.]) until the inside tab has cleared the catch. c.
Installing the 201i server in the Succession 1000 system Standard 1.07 2 Remove the inside front cover plate as follows: A C B G101621 a. Use a screwdriver to loosen each screw on the top of the inside front cover plate by three turns. ATTENTION Do not remove the screws. b. Apply pressure and slide the inside front cover plate upward to the left until the screw holes are aligned with the screw heads. c. Pull the inside front cover plate away from the Media Gateway or Media Gateway Expansion.
November 2006 Installing the 201i server in the Succession 1000 system Installing the 201i server Introduction This section describes how to install the 201i server inside the Media Gateway or Media Gateway Expansion. Before you begin Determine which pair of consecutive slots are to contain the 201i server.
Installing the 201i server in the Succession 1000 system Standard 1.07 To install the 201i server inside the Media Gateway or Media Gateway Expansion 1 Ensure that no cables are connected to the slots in which you are installing the 201i server. 2 Open the lock latches at the top and bottom of the 201i server faceplate. Note: When you open the top lock latch, it breaks the yellow backplane warning label if it has not been removed. The label is not relevant for Succession 1000.
November 2006 ATTENTION Installing the 201i server in the Succession 1000 system Do not push the 201i server into place against the backplane until you are ready to observe the startup cycle. If the Media Gateway or Media Gateway Expansion is connected to a power source, the 201i server receives power as soon as it makes contact with the backplane. What’s next? Continue with “Installing the NTRH3502 SCSI cable for Succession 1000” on page 110.
Installing the 201i server in the Succession 1000 system Standard 1.07 Installing the NTRH3502 SCSI cable for Succession 1000 Introduction Before you can connect a CD-ROM or tape drive to the 201i server, you must install the NTRH3502 SCSI cable. The NTRH3502 SCSI cable has a low profile right-angle connector that allows the cable to be connected to the 201i server faceplate when the Media Gateway or Media Gateway Expansion cover is installed.
November 2006 Installing the 201i server in the Succession 1000 system Note: Alternate connection scenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure that you use appropriate cabling for each device. Before you begin 1. Before you install the SCSI devices in a daisy chain, you must configure the SCSI device IDs and DIP switches. For instructions, see “Preparing peripheral devices,” on page 121.
Installing the 201i server in the Succession 1000 system Standard 1.07 Inner SCSI bracket Note: After you remove the bracket, refasten the screws in their original locations inside the cabinet. G101587 2 Refasten the inner SCSI bracket screws in their original locations inside the Media Gateway or Media Gateway Expansion. You will use one of the screws later to fasten the NTRH3502 SCSI cable drain wire.
November 2006 Installing the 201i server in the Succession 1000 system 5 Replace the inside front cover plate. For instructions, see “To replace the inside front cover plate” on page 114. ATTENTION Ensure that the tabs on the bottom and right side of the inside front cover plate are positioned inside the Media Gateway or Media Gateway Expansion. 6 Replace the front bezel. For instructions, see “To replace the front bezel” on page 116.
Installing the 201i server in the Succession 1000 system Standard 1.07 Replacing the Media Gateway or Media Gateway Expansion cover Introduction This section describes how to replace the front bezel and inside front cover plate on the Media Gateway or Media Gateway Expansion.
November 2006 Installing the 201i server in the Succession 1000 system 1 Insert the bottom tabs of the front cover plate inside the bottom rail. 2 Align the screw holes on the front cover plate over the screw heads on the Media Gateway or Media Gateway Expansion. 3 Slide the front cover plate downward to the right, ensuring that the side tabs slide behind the side rail. 4 Tighten the screws to secure the front cover plate. 5 Continue with “To replace the front bezel,” below.
Installing the 201i server in the Succession 1000 system Standard 1.07 To replace the front bezel WARNING Risk of eye injury . Nortel recommends that you operate the Media Gateway and Media Gateway Expansion with their front bezels installed. When the blue LEDs inside these units are lit, they are very bright. 1 Align the two posts and the locking tab on the rear of the front bezel with the slots on the inside front cover plate.
November 2006 Installing the 201i server in the Succession 1000 system Connecting cables to the Succession 1000 system Introduction The following items are connected to the back of the Media Gateway or Media Gateway Expansion: multi I/O cable (NTRH0912) This cable establishes the connection to the modem, ELAN, and CLAN.
Installing the 201i server in the Succession 1000 system Standard 1.07 c. Secure the connection by tightening the retaining screw and Velcro fastening strap of the conductor. The following diagram shows how to secure the multi I/O cable connection: Velcro fastening strap A Pull to tighten the strap B C G101592 3 Attach the multi I/O cable drain wire to a screw on the Media Gateway or Media Gateway Expansion. See the diagram in step 4.
November 2006 Installing the 201i server in the Succession 1000 system 4 Connect the power cord to the Media Gateway or Media Gateway Expansion. Power cord Drain wire Note: Cabinet is not exactly as shown. G101616 What’s next? Prepare the modem, CD-ROM drive, and tape drive for connection to the 201i server. For instructions, see Chapter 7, “Preparing peripheral devices.
Installing the 201i server in the Succession 1000 system 120 Standard 1.
Chapter 7 Preparing peripheral devices In this chapter Overview 122 Setting the modem DIP switches 124 Setting the CD-ROM drive SCSI ID and DIP switches 126 Setting the tape drive SCSI ID 128 Setting SCSI device termination 130 201i Server Hardware Installation 121
Preparing peripheral devices Standard 1.07 Overview Introduction You can connect a modem and one or more SCSI devices to the 201i server. The modem is connected to the 201i server by the multi I/O cable. The SCSI devices are connected to the 201i server by the intermediate SCSI cable. If there is more than one SCSI device, the devices are daisy chained together. Each device on the SCSI bus must have a unique SCSI ID, and only the last device in the chain is terminated.
November 2006 Preparing peripheral devices tape drive (NTRH9038): Tandberg SLR5 tape drive Note: This is currently the only supported tape drive.
Preparing peripheral devices Standard 1.07 Setting the modem DIP switches Introduction Set the modem DIP switches to their default settings. This section describes how to set the modem DIP switches if they have been changed from the default settings. To set the modem DIP switches Ensure that the DIP switches are set as described in the following table. Use a pair of tweezers or small screwdriver to set the DIP switches. Note: The DIP switches are located on the back of the modem. ON is down. OFF is up.
November 2006 Preparing peripheral devices DIP switch Default setting Function 4 OFF Command mode local echo suppression 5 6 7 8 ON OFF OFF ON OFF: Displays keyboard commands ON: Suppresses echo Auto answer suppression OFF: Modem answers on first ring, or higher if specified in NVRAM ON: Disables auto answer Carrier Detect (CD) override OFF: Modem sends CD signal when it connects with another modem; drops CD on disconnect ON: CD is always ON (override) Power-on and AT
Preparing peripheral devices Standard 1.07 Setting the CD-ROM drive SCSI ID and DIP switches Introduction This section describes how to set the CD-ROM drive SCSI ID and DIP switches. ATTENTION You must power down the CD-ROM drive before changing the SCSI ID and DIP switches. Note: The CD-ROM drive discussed in this section is the external SCSI CD-ROM drive (NTRH9105). To set the CD-ROM drive SCSI ID The SCSI ID setting is located on the back of the CD-ROM drive. (See the diagram that follows.
November 2006 Preparing peripheral devices To set the CD-ROM drive DIP switches Set the CD-ROM drive DIP switches as described in the following table: DIP switch Description Setting 1 Parity ON 2 Termination Note: For more information about daisy chaining SCSI devices, see “Setting SCSI device termination” on page 130. If the CD-ROM drive is the first and only device, set this switch to ON. If the CD-ROM drive is the first device and daisy chained with the tape drive, set this switch to OFF.
Preparing peripheral devices Standard 1.07 Setting the tape drive SCSI ID Introduction This section describes how to set the tape drive SCSI ID. ATTENTION You must power down the tape drive before changing the SCSI ID. Note: The tape drive discussed in this section is the Tandberg SLR5 tape drive (NTRH9038). This is currently the only supported tape drive. To set the tape drive SCSI ID The SCSI ID setting is located on the back of the tape drive. See the diagram on page 129.
November 2006 Preparing peripheral devices To change the SCSI ID, use the blade of a screwdriver to press either the plus (+) or minus (–) button on the SCSI ID switch. Set the SCSI ID to 5. SCSI ID switch AC power receptacle Internally terminated SCSI interface connectors Note: The appearance and size of the tape drive is subject to change. This diagram is an example of the key components on the tape drive's connection panel.
Preparing peripheral devices Standard 1.07 Setting SCSI device termination Introduction If you want to connect SCSI devices in a daisy chain, the last device in the daisy chain must be terminated. This section describes how to terminate the SCSI devices. ATTENTION Ensure that the CD-ROM and tape drives are powered down before changing the device termination. Supported daisy chain connection scenarios The first device in a SCSI device daisy chain can be either the tape drive or the CD-ROM drive.
November 2006 Preparing peripheral devices Meridian 1 For more information about the cabling requirements, see “Installing the SCSI cables for Meridian 1” on page 65.
Preparing peripheral devices Standard 1.
November 2006 Preparing peripheral devices Succession 1000 For more information about the cabling requirements, see “Installing the NTRH3502 SCSI cable for Succession 1000” on page 110.
Preparing peripheral devices Standard 1.07 IF you are connecting THEN a tape drive only do nothing. External termination is not required because the drive is already internally terminated. This is indicated by a label on the back or front of the tape drive. both a CD-ROM drive and a tape drive (the tape drive is the last device) set DIP switch 2 on the back of the CD-ROM drive to OFF. The tape drive is internally terminated. External termination is not required.
Chapter 8 Connecting peripheral devices to the 201i server In this chapter Overview 136 Installing the MPCs 140 Installing the monitor, keyboard, and mouse 142 Connecting the CD-ROM and tape drives 144 Connecting the 201i server to the switch, ELAN, and CLAN 153 Connecting the modem 156 Completing the installation 159 201i Server Hardware Installation 135
Connecting peripheral devices to the 201i server Standard 1.07 Overview Introduction This section describes installing the 201i server in the switch, connecting peripheral devices, and starting the 201i server. Connecting the 201i server to the network The switch, ELAN, CLAN, and modem connections are established by using the 201i server multi I/O cable. The switch connector is a 50-pin amphenol connector.
November 2006 Connecting peripheral devices to the 201i server Monitor, keyboard, and mouse Connect the monitor, keyboard, and mouse to the 201i server faceplate so that you can: observe the 201i server startup process. run the Configuration Wizard. perform initial administration after installation. The 201i server is not intended to operate with permanent monitor, keyboard, and mouse connections.
Connecting peripheral devices to the 201i server Standard 1.
November 2006 Connecting peripheral devices to the 201i server Starting the 201i server When you lock the 201i into position against the switch backplane, the server starts automatically. You can observe the startup process on both the monitor and the 201i server faceplate. ATTENTION Ensure that all peripheral devices are connected before you lock the 201i server in position against the backplane. The 201i server receives power and starts when the connection with the backplane is established.
Connecting peripheral devices to the 201i server Standard 1.07 Installing the MPCs Introduction Two MPCs are preinstalled at the factory. This section describes how to install additional cards, if required. Correct card insertion The MPC-8 card is keyed so that it fits only one way into the slot on the 201i server faceplate. If the card is inserted incorrectly, the card does not go all the way into the slot. CAUTION Risk of equipment damage .
November 2006 Connecting peripheral devices to the 201i server facing to the right if the 201i server is inserted into the 201i shelf (see the following diagram) G101541 3 Insert the card into the slot, and gently push it until it is firmly in place and the ejector button pops back out. Note: Populate MPC slots in numerical order as listed on the 201i server faceplate. What’s next? Continue with “Installing the monitor, keyboard, and mouse” on page 142.
Connecting peripheral devices to the 201i server Standard 1.07 Installing the monitor, keyboard, and mouse Introduction You must connect the monitor, keyboard, and mouse to the 201i server so that you can: observe the 201i server startup process. run the Configuration Wizard. perform initial administration after installation. Note: The 201i server is not intended to operate with permanent monitor, keyboard, and mouse connections.
November 2006 Connecting peripheral devices to the 201i server PS/2 extension cable The following diagram shows the PS/2 extension cable connected between the 201i server and the USB mouse with USB-to-PS/2 converter. 201i server faceplate PS/2 extension cable (A0855616) USB-to-PS/2 converter Monitor cable G101619 To connect the monitor, keyboard, and mouse 1 Connect the monitor to the 201i server faceplate using a DB-15 cable. 2 Connect the monitor power cord, and then power up the monitor.
Connecting peripheral devices to the 201i server Standard 1.07 Connecting the CD-ROM and tape drives Introduction You can connect the CD-ROM, tape drive, or both to the intermediate SCSI cable that you installed earlier. Before you begin Before you can connect the CD-ROM or tape drive, ensure that you have completed the following tasks: 1. Install the intermediate SCSI cable. For See Meridian 1 “Installing the SCSI cables for Meridian 1” on page 65.
November 2006 Connecting peripheral devices to the 201i server Selecting the procedure for your switch IF you are working with THEN see a large Meridian 1 switch (such as Option 51) “To connect the CD-ROM and tape drives to the 201i server (Meridian 1)” on page 145. Option 11C “To connect the CD-ROM and tape drives to the 201i server (Option 11C)” on page 147. Option 11C Mini “To connect the CD-ROM and tape drives to the 201i server (Option 11C Mini)” on page 149.
Connecting peripheral devices to the 201i server Standard 1.07 IF the first device is the THEN tape drive do the following: a. Attach the A0769312 SCSI adapter to the tape drive. b. Connect the SCSI adapter to the NTRH1410 cable that you connected earlier to the Meridian 1 I/O panel. 3 Connect the low-profile right-angle SCSI cable connector to the SCSI connector on the 201i server faceplate.
November 2006 Connecting peripheral devices to the 201i server that is not described in this guide, ensure that you use appropriate cabling for each SCSI device. 5 Connect the power cord for each device. 6 Power up the devices. 7 Continue with “What’s next?” on page 152. To connect the CD-ROM and tape drives to the 201i server (Option 11C) 1 Connect the first SCSI device.
Connecting peripheral devices to the 201i server Standard 1.07 The following diagram shows cable connections, where the CD-ROM drive is the first device: 201i cabling Peripheral cabling Option 11C Optional 201i NTRH30AA NTRH9038 Tape drive NTRH1407 Bracket assembly Tape drive SCSI cable NTRH3502 NTRH9105 CD-ROM drive CD-ROM drive SCSI cable NTRH3502 G101434 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
November 2006 Connecting peripheral devices to the 201i server To connect the CD-ROM and tape drives to the 201i server (Option 11C Mini) 1 Connect the first SCSI device. 2 Follow instructions below. IF the first device is the THEN CD-ROM drive do the following: a. Attach the A0769312 SCSI adapter to the CD-ROM drive. b. Connect the NTRH3502 SCSI cable that you installed earlier on the Option 11C Mini to the SCSI adapter on the CD-ROM drive.
Connecting peripheral devices to the 201i server 201i cabling Standard 1.07 Peripheral cabling Option 11C Mini Optional 201i NTRH30AA NTRH9038 Tape drive Tape drive SCSI cable NTRH3502 NTRH9105 CD-ROM drive CD-ROM drive SCSI cable NTRH3502 SCSI adapter A0769312 G101595 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
November 2006 Connecting peripheral devices to the 201i server To connect the CD-ROM and tape drives to the 201i server (Succession 1000) 1 Connect the first SCSI device. 2 Follow instructions below: IF the first device is the CD-ROM drive THEN do the following: a. Attach the A0769312 SCSI adapter to the CD-ROM drive. b. Connect the NTRH3502 SCSI cable that you installed earlier on the Succession 1000 Media Gateway or Media Gateway Expansion to the SCSI adapter on the CD-ROM drive.
Connecting peripheral devices to the 201i server Standard 1.07 The following diagram shows cable connections, where the CD-ROM drive is the first device: 201i cabling Peripheral cabling Succession 1000 Media Gateway or Media Gateway Expansion Optional NTRH9038 Tape drive 201i NTRH30AA Tape drive SCSI cable NTRH3502 NTRH9105 CD-ROM drive CD-ROM drive SCSI cable NTRH3502 SCSI adapter A0769312 G101615 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide.
November 2006 Connecting peripheral devices to the 201i server Connecting the 201i server to the switch, ELAN, and CLAN Introduction The CLAN and ELAN connections are established by using the 201i server multi I/O cable. ATTENTION For important considerations about using the Embedded LAN (ELAN) in your network, see “About the ELAN” in the CallPilot Installation and Configuration Task List.
Connecting peripheral devices to the 201i server IF you are installing the 201i server in a Option 11C Mini or Succession 1000 Standard 1.07 THEN ensure that the 50-pin amphenol connector on the multi I/O cable (NTRH0912) is connected to the high-density connector associated with the left slot occupied by the 201i server. Note: Ensure that the cable is securely fastened.
November 2006 Connecting peripheral devices to the 201i server Option 11C Mini or Succession 1000 to a screw on the back of the cabinet Drain wire G101593 3 Connect the connector on the multi I/O cable that is labeled as ELAN to the switch network hub. 4 If CLAN is required, connect the connector on the multi I/O cable that is labeled as CLAN to the CLAN 10- or 100Base-T-compliant network hub. What’s next? Continue with “Connecting the modem” on page 156.
Connecting peripheral devices to the 201i server Standard 1.07 Connecting the modem Introduction You must connect the modem to the 201i server if: you want to administer the 201i server from a remote location. you need assistance from Nortel technical support.
November 2006 Connecting peripheral devices to the 201i server 2 Attach the serial cable as follows: a. Connect the 25-pin male end of the serial cable to the modem. b. Attach the 0.25-inch nuts to the thumbscrews on the 9-pin female connector on the serial cable. c. Connect the 9-pin female connector to the RS-232 COM1 connector on the multi I/O cable and tighten the nuts. 3 Connect one end of the RJ-11 phone cord to the line jack on the modem and the other end to an analog jack.
Connecting peripheral devices to the 201i server Standard 1.07 6 Power on the modem. Note: Ensure that the modem is receiving power by checking that at least one LED on its front panel is lit. 7 Place the modem in an area where it cannot be accidentally damaged or where people cannot trip over attached cords. What’s next? Continue with “Completing the installation” on page 159.
November 2006 Connecting peripheral devices to the 201i server Completing the installation Introduction To complete the installation of the 201i server, lock the 201i into position. The server starts up automatically. ATTENTION When connecting the optional CLAN, do not power up unless your antivirus programs and Nortel security updates are installed first. To complete the installation and start the 201i server Note: Ensure that the switch in which the 201i is installed is powered on.
Connecting peripheral devices to the 201i server Standard 1.07 Result: The operating system boot sequence begins, and communication with the switch occurs. The HEX display shows NT (for about 30 seconds), followed by OK. Note: The system reboots more than once. The HEX display repeats with each reboot. Note: Before OK appears, one of the following messages can appear, but not for more than one second: CDLN, C:01, or C:02. This is normal operation.
November 2006 Connecting peripheral devices to the 201i server 6 Ensure that the operating system logon window appears on the monitor. If the logon window does not appear, refer to the CallPilot Server Maintenance and Diagnostics guide for your server for troubleshooting instructions. What’s next? Proceed with the CallPilot and CallPilot Server Configuration guide for your switch and server to connect and configure the server and switch.
Connecting peripheral devices to the 201i server 162 Standard 1.
Appendix A RoHS part conversion table In this appendix RoHS part conversion table 201i Server Hardware Installation 164 163
RoHS part conversion table Standard 1.07 RoHS part conversion table This appendix provides a mapping of RoHS-compliant parts to the equivalent non-RoHS-compliant parts for the 201i server. Nortel is phasing in RoHS-compliant 201i servers in countries affected by the EUED (European Union Environmental Directives).
CallPilot 4.0 IPE Unified Messaging Starter Bundle (EMEA Bundle) CallPilot 4.0 IPE Stand-By System CallPilot 4.
(The non-RoHS part description is included below in parentheses if it is different from the RoHS part description) CallPilot External CD-ROM Drive Kit MPC-8 H/W Portable Tape Drive Assembly H/W Assy Portable CD ROM Drive SCSI Adapter, 50p Centronics to HD SCSI-3 Adapter, 68p HD Male to 50p Centronics Female Multi I/O w/ Dual Ethernet M1 Unfiltered R/T Cable External SCSI Tape Cable 14ft Shielded Ethernet Cable SCSI Gender Changer for 11C Mini / CS 1000S Cable Assembly for Option 11C SCSI Ca
201i Server Hardware Installation M1 Bulkhead SCSI Cable External SCSI Tape Cable Combo Key/Mouse (Non-RoHS: HW Perip 101 Enhanced K/Board) Combo Key/Mouse (Non-RoHS: 3 Button Mouse) 15 Inch LCD Monitor (Non-RoHS: 15" Flat-panel LCD Display Monitor) Spare Cleaning Cartridge (Non-RoHS: Cleaning Cartridge) Spare SLR75 Media (Non-RoHS: Data Cartridge 4.0/8.
RoHS part conversion table 168 Standard 1.
Index Numerics A 201i server components, diagram 18 damaged, what to do 42 faceplate connections 31 description 20 diagram 19, 138 inspecting 42 installation checklist 37–40 prerequisites 44 installing large Meridian 1 systems 56 Option 11C 72 Option 11C Mini 72 Succession 1000 108 motherboard, description 18 network setup Meridian 1 24 Succession 1000 26 peripheral device connectors, diagram 138 primary components 16 relative humidity 22 reset button 22 RoHS compliance 16 starting 139, 159–161 Succession
Index connectors CLAN 29 ELAN 29 RS-232 30 switch 29 diagram 28 installing large Meridian 1 system 153 Option 11C 153 Option 11C Mini 92, 154 Succession 1000 154 cable, SCSI 110 Meridian 1 49, 65 connections, establishing 69 installing 68 NTRH1407, diagram 79 Option 11C 78 bracket assembly, installing 82 connections, establishing 83 installing 81 Option 11C Mini 86 installing 88–91 Succession 1000, installing 111–113 cabling, SCSI devices Meridian 1 131 Option 11C 132 Option 11C Mini 132 Succession 1000 13
November 2006 keyboard 20, 31 monitor 20, 31 mouse 20, 31 SCSI 32 SCSI device 21 switch, multi I/O cable 29 copyright 2 cover, removing small Meridian 1 systems 73 Succession 1000 104–106 covers, replacing Succession 1000 114–116 D daisy chaining SCSI devices Meridian 1 131 Option 11C 132 Option 11C Mini 132 Succession 1000 133 damaged server, what to do 42 device termination, setting CD-ROM drive 133 tape drive 134 devices, peripheral CD-ROM drive 32 Ethernet hub 33 keyboard 33 modem 33 monitor 33 mouse
Index CD-ROM drive 127 modem 124 documentation, Succession 1000 103 drain wire, connecting Option 11C 154 Option 11C Mini 155 Succession 1000 155 E ejector buttons, MPCs 21 ELAN LED 22 requirements 28, 45 environmental specifications humidity 22 temperatures 22 Ethernet hub 33 F faceplate, 201i server connections 31 description 20 diagram 19, 138 peripheral device connectors 138 fax modem connecting 156 DIP switches, setting 124 G Standard 1.
November 2006 L latches, lock 20 LEDs CLAN 22 ELAN 22 hard drive 22 MPC status 20–21 power status 20 SCSI drive 22 lock latches 20 M Media Gateway and Media Gateway Expansion See Succession 1000 Meridian 1 backplane (tip and ring) cable existing cables, removing 59 NTRH3501, installing 63 connection requirements 45 I/O panel connections 48 network setup 24 SCSI cables, installing 68 slot requirements 44 modem 33 connecting 156 connections diagram 157 DIP switches, setting 124 monitor 31 connecting 143 con
Index installation diagram 68 installing 68 NTRH1410 cable 66 installation diagram 68 installing 68 NTRH3501 cable 58 diagram 62 installing 63 NTRH3502 cable 86, 110 installation diagrams Option 11C Mini 90 Succession 1000 113 installing Option 11C Mini 88–91 Succession 1000 111–113 O Option 11C Mini multi I/O cable, installing 92 power cable installing 93 SCSI cable 86 Option 11C, installing intermediate SCSI cable 81 P part numbers CD-ROM drive 32 Ethernet hub 33 keyboard 33 modem 33 monitor 33 mouse 3
November 2006 daisy chain scenarios Meridian 1 131 Option 11C 132 Option 11C Mini 132 Succession 1000 133 installation, attention 126, 128, 130 supported 122 SCSI drive LED 22 SCSI IDs, setting CD-ROM drive 126 tape drive 128 secondary backplane connector description 48, 51 diagram 51 installing for Meridian 1 52–55 reason for moving 50 required tools 52 server, 201i components, diagram 18 damaged, what to do 42 faceplate 19, 138 inspecting 42 installation checklist 37–40 prerequisites 44 installing large
Index connecting Meridian 1 145 Option 11C 147 Option 11C Mini 149 Succession 1000 151 description 33 device termination, setting 134 installation, attention 126, 128, 130 setting SCSI ID 128 temperatures, 201i server 22 tip and ring cable 49, 62 establishing connections 64 installing NTRH3501 63 removing 59 removing from Meridian 1 61 trademarks 2 176 Standard 1.
201i Server Hardware Installation CallPilot Release 4.0 Document Number: 555-7101-220 Document Version: Standard 1.07 November 2006 All Rights Reserved. To provide feedback or report a problem in this document, go to www.nortel.com/documentfeedback. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.
