Part No.
Copyright © 2000 Nortel Networks All rights reserved. April 2000. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks NA Inc.
Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) Statement Taiwan Requirements Bureau of Standards, Metrology and Inspection (BSMI) Statement Canada Requirements Only Canadian Department of Communications Radio Interference Regulations This digital apparatus (Passport 8100 Modules) do not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
2. Restrictions on use; reservation of rights. The Software and user manuals are protected under copyright laws. Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including any revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals.
Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such intended examination of the Software and may procure support and assistance from Nortel Networks. 7. Term and termination.
vi 204515-C
Contents Preface Before You Begin ............................................................................................................. xv Text Conventions .............................................................................................................xvi Related Publications .......................................................................................................xvii How to Get Help .........................................................................................
Chapter 2 Installing a Passport 8100 Module Chassis Configuration Requirements .............................................................................2-2 Safety and Environmental Precautions ..........................................................................2-2 Installing a Module ..........................................................................................................2-3 Turning On the Chassis Power ..............................................................................
Appendix A Technical Specifications General Specifications ................................................................................................... A-1 Passport 8190SM Switch Management Module ............................................................ A-3 Management Port .................................................................................................... A-4 Console Serial Port .................................................................................................
Appendix C Media Dependent Adapters 450 Series MDAs ........................................................................................................... C-2 8100-4TX MDA .............................................................................................................. C-4 8100 Series Fiber MDAs ............................................................................................... C-5 Installing an MDA ...............................................................................
Figures Figure 1-1. Passport 8190SM Switch Management Module ......................................1-4 Figure 1-2. LEDs on the Passport 8190SM Module ...................................................1-7 Figure 1-3. Passport 8132TX Edge Switch Module ...................................................1-8 Figure 1-4. LEDs on the Passport 8132TX Module ..................................................1-10 Figure 1-5. Passport 8148TX Edge Switch Module ..............................................
xii Figure C-1. 1000BASE-SX (Shortwave Gigabit) MDA Front Panels ......................... C-2 Figure C-2. 1000BASE-LX (Longwave Gigabit) MDA Front Panels .......................... C-3 Figure C-3. 8100-4TX MDA Front Panel .................................................................... C-4 Figure C-4. 8100 Series MDA Front Panels .............................................................. C-6 Figure C-5. Installing an MDA ....................................................................
Tables Table 1-1. Power Supply Hot-Swapping ................................................................1-15 Table 2-1. Connectors and Cables for Passport 8000 Series Edge Switch Modules .........................................................................2-6 Table 3-1. Access Levels and Default Login Values ................................................3-4 Table 4-1. LED Indications of Problems ...................................................................4-3 Table A-1.
xiv 204515-C
Preface Passport™ 8100 modules installed in an Passport 8000 Series chassis create an edge switch entity within the chassis. These high-performance, low-cost Ethernet switches from Nortel Networks™ provide a high-density layer 2 switching system that is ideal for wiring closet applications. This guide provides information about the features and capabilities of the Passport 8100 modules, including module specifications and switch startup procedures.
Using the Passport 8100 Modules Text Conventions This guide uses the following text conventions: angle brackets (< >) Indicate that you choose the text to enter based on the description inside the brackets. Do not type the brackets when entering the command. Example: If the command syntax is: ping , you enter: ping 192.32.10.12 braces ({}) Indicate required elements in syntax descriptions where there is more than one option. You must choose only one of the options.
Preface separator ( > ) Shows menu paths. Example: Protocols > IP identifies the IP option on the Protocols menu. vertical line ( | ) Separates choices for command keywords and arguments. Enter only one of the choices. Do not type the vertical line when entering the command. Example: If the command syntax is: show ip {alerts | routes}, you enter either: show ip alerts or show ip routes, but not both.
Using the Passport 8100 Modules • Installing the Passport 8010 Chassis (part number 204518-B) Describes installation procedures for the Passport 8010 chassis. • Installing the Passport 8006 Chassis (part number 207313-B) Describes installation procedures for the Passport 8006 chassis. • Installing the Passport 8001PS AC Power Supply (part number 204519-B) Describes installation and connection procedures for the Passport 8001PS AC power supply.
Preface How to Get Help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance.
Chapter 1 About the Passport 8100 Modules The Passport 8100 modules provide a full complement of switching capabilities in a Passport 8000 Series chassis. The Passport 8100 modules provide 10/100 megabit per second (Mb/s) autonegotiating twisted pair Ethernet ports, 100 Mb/s fiber Ethernet ports, and fiber Gigabit Ethernet ports. A Passport 8000 Series chassis with installed Passport 8100 modules constitutes a single switching entity with distributed management and full redundancy.
Using the Passport 8100 Modules This chapter includes the following information: • Summary of features • Detailed descriptions of each module Features The Passport 8100 modules have the following features: • One active and one optional standby CPU subsystem with fast fail-over in the event of loss of one CPU • Hardware redundancy features, including power supplies, chassis fans, and switch management modules • High-speed forwarding rate, up to 3 million packets per second (peak) • Store-and-forw
About the Passport 8100 Modules • IEEE 802.1Q port-based virtual LANs (VLANs) • IEEE 802.1p prioritization • IEEE 802.
Using the Passport 8100 Modules • A command line interface (CLI) for managing the Passport 8100 switch, accessible through the Passport 8190SM module or through a Telnet connection If a Passport 8190SM module is not installed, the CLI is accessible through the Comm port on the Passport 8132TX module.
About the Passport 8100 Modules The Passport 8190SM module fits into either slot 5 or slot 6 in the Passport chassis. Image, configuration, and log files are maintained on the flash memory (onboard and PCMCIA) of this module. The module also provides out-of-band management by using the Ethernet port on the module. Note: Nortel Networks recommends using the Ethernet port on the Passport 8190SM module for management rather than a switched port.
Using the Passport 8100 Modules Note: This port should be used only as a management port. It does not provide network connectivity. DTE/DCE Switch The DTE/DCE switch changes the pin assignments on the Console port and allows you to designate the connector as either DTE or DCE. For information about pin assignments for this port, refer to Appendix A, “Technical Specifications.” Serial Ports The Passport 8190SM module provides two serial ports for attachment of modem or console devices.
About the Passport 8100 Modules LEDs LEDs on the Passport 8190SM module indicate the status of the module subsystems, chassis power supplies, and chassis fans (Figure 1-2). 6 1 Management Link 100 7 Utilization% 3 2 Power Supply Master CPU 25 1 2 50 75 100 1 Fan 3 2 Temp Online 4 5 9674EA 1 = Management port LEDs 2 = CPU utilization LEDs 3 = Fan LEDs 4 = Temp LED Figure 1-2.
Using the Passport 8100 Modules Passport 8132TX 32-Port I/O Module The Passport 8132TX module (Figure 1-3) is a single-slot I/O module for the Passport 8000 Series chassis. It has 32 autosensing 10BASE-T/100BASE-TX switched ports with RJ-45 connectors. The ports have integrated LEDs to indicate port operation, and the module has three additional LEDs to indicate system operation. An expansion slot allows you to install an MDA to provide additional port types.
About the Passport 8100 Modules MDA Slot The MDA slot allows you to install optional media dependent adapters (MDAs) that support a range of media types.
Using the Passport 8100 Modules Note: Nortel Networks recommends using the Passport 8190SM module to configure and manage your switch. The Comm port on the Passport 8132TX module is active only when no Passport 8190SM module is present and when the Passport 8132TX module is operating as the master module. The Comm port on the Passport 8132TX module is configured as a data communications equipment (DCE) connector. Be sure that your RS-232 cable pinouts are configured for DCE connections.
About the Passport 8100 Modules Passport 8148TX 48-Port I/O Module The Passport 8148TX module provides 48 autonegotiating 10/100 Mb/s ports (Figure 1-5). Each port can operate in full- or half-duplex mode. Autonegotiation circuitry automatically negotiates the highest possible data rate and the duplex operation possible with the attached device, if the attached device supports IEEE 802.3u autonegotiation. 9672EA Figure 1-5.
Using the Passport 8100 Modules LEDs Each port on the Passport 8148TX module has two LEDs that indicate data speed and activity for the port (Figure 1-6). In addition, the module has three LEDs to indicate system operating conditions. For details of LED operation, refer to Appendix B, “LEDs.” 1 2 3 9120EA Figure 1-6.
About the Passport 8100 Modules For more information about the GBICs and instructions to install them, refer to Appendix D, “Installing GBICs.” 9681EB Figure 1-7. Passport 8108GBIC Module LEDs Each port has an associated Link LED and Act (activity) LED to indicate link and TX/RX activity (Figure 1-8). In addition, the module has three LEDs to indicate system operating conditions. For details of LED operation, refer to Appendix B, “LEDs.
Using the Passport 8100 Modules Redundant Passport 8190SM Modules When you install two Passport 8190SM modules in a Passport 8000 Series chassis, one provides the active CPU functions for the switch; the CPU subsystem on the other module is in standby mode. If the active CPU fails, the standby CPU assumes the CPU functions for the switch within 1 second. Then the module relearns the routing databases for the switch.
About the Passport 8100 Modules Table 1-1.
Using the Passport 8100 Modules Combining Passport 8100 and Passport 8600 Modules Although the Passport system software allows you to install both Passport 8100 Series and Passport 8600 Series modules in the same switch chassis, Nortel Networks does not recommend such a configuration for the following reasons: 1-16 • Each type of modules functions as a separate switching entity in the chassis, with no switched connection between the two.
Chapter 2 Installing a Passport 8100 Module This chapter provides instructions for installing and connecting the Passport 8100 modules in a Passport 8000 Series chassis. For more information about your chassis, refer to the documentation that was shipped with the chassis. The initial switch setup tasks are described in Chapter 3, “Basic Switch Configuration.
Using the Passport 8100 Modules Chassis Configuration Requirements Slots in the Passport 8000 Series chassis are numbered from the top down, starting with 1. In either the Passport 8010 or the Passport 8006 chassis, slots 5 and 6 are reserved for the Passport 8190SM Switch Management Module. Any of the Passport 8100 Series I/O modules can be installed in the remaining chassis slots. Note: You must install an I/O module in slot 1 or slot 2 to provide bus master functions in the switch.
Installing a Passport 8100 Module Installing a Module To install a module in a Passport 8000 Series chassis: 1. Remove the filler panel from the slot where you will install the module (Figure 2-1). 9058FA Figure 2-1. 2. Removing a Filler Panel Make sure the inserter/extractor levers are extended away from the front of the module (Figure 2-2). 9397FA Figure 2-2.
Using the Passport 8100 Modules 3. Slide the module into the slot (Figure 2-3). 9398FA Figure 2-3. 4. Inserting a Module Rotate the inserter/extractor levers to seat the module backplane connectors (Figure 2-4). 9399FA Figure 2-4.
Installing a Passport 8100 Module 5. Tighten the retaining screws to secure the module in the chassis (Figure 2-5). 9400FA Figure 2-5. Securing the Module in the Chassis Turning On the Chassis Power Although you can install or replace modules in an operating chassis, in a new installation you may prefer to install all the modules before turning on the chassis power. To turn on the chassis power: 1.
Using the Passport 8100 Modules Connecting Cables After the modules are installed and the chassis is powered on, connect network cables. Table 2-1 shows the connector types and recommended cables for each module. Table 2-1.
Installing a Passport 8100 Module Nortel Networks recommends that you route all network cables through the supplied cable management brackets (Figure 2-6). 9573FA Figure 2-6. Routing Network Cables Replacing Modules Any of the Passport 8100 modules can be removed from an operating switch chassis without turning off the chassis power.
Using the Passport 8100 Modules To replace a module: 2-8 1. Disconnect all network cables from the module to be removed. 2. Loosen the module retaining screws. 3. Rotate the inserter/extractor levers to disconnect the module from the backplane connectors. 4. Remove the module from the chassis. 5. Insert the new module in the chassis and tighten the retaining screws. 6. Reconfigure the ports of the new module as necessary. 7. Reconnect the cables.
Chapter 3 Basic Switch Configuration This chapter describes how to use the command line interface (CLI) for basic switch configuration.
Using the Passport 8100 Modules Specifying Port Numbers Each port number on the Passport switch consists of a slot number and a position number in the format /. The slot number identifies the chassis slot containing the I/O module with that port. The position number identifies the position of the port on the I/O module. Chassis slots are numbered from the top down, and ports are numbered generally from left to right beginning with 1 for the far left port.
Basic Switch Configuration Booting the Switch When you turn on the switch power supplies, the switch begins its automatic boot process. The default boot order is to try to boot the switch first from the PCMCIA card, then from the internal flash memory, and finally over the network. If a terminal is connected to the Console port, you can watch the system messages that record the boot sequence. You can modify this boot order using the boot monitor command line interface (CLI).
Using the Passport 8100 Modules Logging On to the System The Passport 8100 switches have four levels of security access for device management. Table 3-1 describes the access levels and lists their default login names and passwords. Table 3-1. Access Levels and Default Login Values Default Login Default Password Access Level Description Read-Only Allows only viewing of configuration and status ro information. Is equivalent to SNMP read-only community access.
Basic Switch Configuration Assigning an IP Address to the Management Port You must assign an IP address to the Management port before you can use it for out-of-band management. To assign an IP address: • Use the following command: config bootconfig net mgmt ip where: specifies the IP address and mask of the Console Management port. Note: The preferred route for managing the switch is to use the Management port.
Using the Passport 8100 Modules Setting System Security System security parameters allow you to define login names and passwords for access to the switch management functions and to specify the access methods, such as through a Telnet session or through a Web browser. To set system security: 1. Change CLI users and passwords using the following commands: • config cli password ro []—changes the Read-Only login and/or password.
Basic Switch Configuration 4. Change Web passwords using the command: config web-server set password ro where: is the user’s login name, up to 20 characters long. is the password associated with the login name, up to 20 characters long. To enable or disable Telnet access, you set flags from the boot monitor CLI. You can access the boot monitor CLI while the switch is booting. To set up Telnet access: 1.
Using the Passport 8100 Modules Switch Configuration The Passport 8100 Series modules provide layer 2 switching as soon as you install them and turn on the switch power. The default configuration includes a single VLAN with a VLAN ID of 1 that contains all the ports in the switch. The only configuration you need to do for the Passport 8100 Series switch is to assign an IP address and a gateway address (default route) for remote management.
Basic Switch Configuration 3. Specify a default gateway address/default route. When configuring IP on most layer 2 switches, you need to specify the IP address of the device and the IP address of the default gateway. Use the following Boot Monitor CLI command to specify the default route: net mgmt route net 0.0.0.0 Use the following Run-Time CLI command to specify the default route: config bootconfig net mgmt route net 0.0.0.
Chapter 4 Troubleshooting This chapter describes troubleshooting techniques for the Passport 8100 modules.
Using the Passport 8100 Modules Failure to Get a Login Prompt from the Console Port If you have connected a terminal to the Console port on the Passport 8190SM module and fail to get a login prompt, the port may have an incorrect DCE/DTE setting. Try moving the DCE/DTE switch from its current setting to the other position (Figure 4-1). Console ink 00 DCE|DTE 9595EA Figure 4-1.
Troubleshooting Table 4-1. LED Indications of Problems Symptom Probable Cause Corrective Action Green power supply LEDs are off. The switch is not receiving AC power. Verify that each AC power cord is fastened securely at both ends and that power is available at each AC power outlet. Verify that each power supply is turned on. The Link/Activity LED for a connected port is off or does not blink (and you have reason to believe that traffic is present).
Using the Passport 8100 Modules Port Connection Problems Port connection problems can usually be traced to a poor cable connection or to an improper connection of the port cables at either end of the link. These types of problems can be remedied by making sure that the cable connections are secure and that the cables are connected to the correct ports at both ends of the link. For more information about cabling, see “Cabling,” next in this chapter.
Troubleshooting The fiber MDAs use only multimode 62.5/125 µm fiber cable. The Nortel Networks 100BASE-FX MDA is not supported on single-mode fiber. SC connectors are used on 2-port 100BASE-FX MDAs, and MT-RJ connectors are used on 4-port 100BASE-FX MDAs. Cables for the GBICs vary depending on the specific GBIC type. For details of the cable requirements for GBICs, refer to Appendix A, “Technical Specifications.
Using the Passport 8100 Modules To correct this mode mismatch problem: 1. Use the CLI to disable autonegotiation for the suspect port. Refer to Reference for the Passport 8000 Command Line Interface Switching Operations for the appropriate CLI commands. 2. Use the CLI to set the speed and duplex mode of the port to match the speed/duplex mode of the connected station. You may have to try several settings before you find the correct speed/duplex mode of the connected station.
Troubleshooting Installation-Related Issues Ethernet networks tend to be fairly simple, but they can still have problems that take time to resolve. The most common problems are associated with the actual network wiring. If you have problems with a newly established network (initial setup), the trouble is most likely related to cabling or addressing.
Appendix A Technical Specifications This appendix lists technical specifications for the Passport 8100 modules. The appendix includes the following information: • • General specifications Specifications for individual modules, including: — Physical specifications — Connector types and, where appropriate, pin assignments — Required cables • • MDI and MDI-X connections Declaration of Conformity General Specifications Standards Supported IEEE 802.3 CSMA/CD (ISO/IEC 8802-3) IEEE 802.
Using the Passport 8100 Modules Data Rate and Encoding 10 Mb/s Manchester encoding 100 Mb/s 4B/5B encoding 1000 Mb/s 8B/10B encoding Environmental Specifications Operating Temperature: 5° to 40° C (41° to 104° F) Storage Temperature: –25° to 70° C (–13° to 158° F) Operating Humidity: 85% maximum relative humidity, noncondensing Storage Humidity: 95% maximum relative humidity, noncondensing Operating Altitude: 3000 m (10,000 ft) maximum Free Fall/Drop: ISO 4180-s, NSTA 1A Vibration: IEC 68-2-6/3
Technical Specifications Electromagnetic Emissions Meets requirements of: US: FCC CFR 47, Part 15, Subpart B, Class A Canada: ICES-003, Issue-2, Class A Australia/New Zealand: AS/NZS 3548:1995, Class A Japan: VCCI V-3/97.04, Class A Taiwan: CNS 13438, Class A EN 55 022 (CISPR 22:1985), Class A CE Mark Electromagnetic Immunity: EN50082-1:1997 Passport 8190SM Switch Management Module Physical Specifications Height: 1.5 in. (3.8 cm) Width: 15.4 in. (39.1 cm) Depth: 18.5 in. (47.
Using the Passport 8100 Modules Management Port The Management port is a 10/100 Mb/s Ethernet port implemented on an RJ-45 connector wired as an MDI connection. Table A-1 shows the pin assignments for this connector. Table A-1.
Technical Specifications Table A-2 lists the pin assignments for the Console port for both the DTE and DCE settings. Table A-2. Pin Assignments in the Passport 8190SM Console Port Connector 1 6 5 9 9473EA Pin Number DCE Signal DTE Signal 2 RXD TXD 3 TXD RXD 4 DTR DSR 5 GND GND 6 DSR DTR 7 RTS CTS 9 CTS RTS Modem Serial Port The Modem serial port is implemented on a DB-9 connector wired as a DTE connection.
Using the Passport 8100 Modules Passport 8132TX Module Physical Specifications Height: 1.5 in. (3.8 cm) Width: 15.4 in. (39.1 cm) Depth: 18.5 in. (47.0 cm) Weight: 8.
Technical Specifications Comm Port Connector The cable used to connect the comm port is a serial cable with a mini-DIN connector on one end to connect to the Passport 8132TX comm port and a DB-25 connector on the other to connect to a terminal or computer. This cable and a DB-25 to DB-9 adapter are shipped with the Passport 8000 Series chassis. Note: The Comm port on the Passport 8132TX module is active only when the chassis has no installed Passport 8190SM module.
Using the Passport 8100 Modules Passport 8148TX Module Physical Specifications Height: 1.5 in. (3.8 cm) Width: 15.4 in. (39.1 cm) Depth: 18.5 in. (47.
Technical Specifications Passport 8108GBIC Module Physical Specifications Height: 1.5 in. (3.8 cm) Width: 15.4 in. (39.1 cm) Depth: 18.5 in. (47.
Using the Passport 8100 Modules 1000BASE-SX GBIC Cable Specifications Type: 62.5 µm or 50 µm multimode fiber Maximum Distance: 1804 ft (550 m) Optical Specifications Wavelength: 850 nm (VCSEL) Average Transmit Output Power: -9.5 to -4 dBm Average Receiver Sensitivity: -17 dBm (minimum) 1000BASE-LX GBIC Cable Specifications Type 62.5 µm multimode fiber or 9 µm single-mode fiber Note: Multimode fiber may require a DMD patch cord.
Technical Specifications 1000BASE-XD GBIC Cable Specifications Type: 9 µm single-mode fiber Maximum Distance: 31 mi (50 km) Note: For a shorter link distance, you may need an in-line attenuator to prevent overloading the receiver. Optical Specifications Wavelength: 1550 nm (DFB laser diode) Average Transmit Output Power: -5.
Using the Passport 8100 Modules MDI and MDI-X Connections For communication to take place between two devices, the transmitter of one device must connect to the receiver of the other device. The connection must be achieved through a crossover function, which could be a crossover cable or a port that implements the crossover function internally. The Passport 8100 modules use MDI-X ports that allow you to connect directly to end stations without using crossover cables (Figure A-1).
Technical Specifications If you are connecting a device to the Passport 8100 module that also implements MDI-X ports (Figure A-2), use a crossover cable. Passport 8000 switch 1 8 T R 8 1 8 Switch or hub 8 1 1 1 RX+ 1 1 RX+ 1 2 RX- 2 2 RX- 2 3 TX+ 3 3 TX+ 3 4 4 4 4 5 5 5 5 6 TX- 6 6 7 7 7 7 8 8 8 8 MDI-X port Crossover cable TX- T R 6 MDI-X port 618EF Figure A-2.
Appendix B LEDs This appendix describes the LED locations and meanings for the following Passport 8000 Series modules: • Passport 8190SM Switch Management Module (this page) • Passport 8132TX and 8148TX I/O Modules (page B-3) • Passport 8108GBIC Module (page B-4) Passport 8190SM Switch Management Module Figure B-1 shows the LEDs on the Passport 8190SM module. Table B-1 describes the operation of these LEDs.
Using the Passport 8100 Modules Table B-1. Label Color/State Meaning Link Green/Steady The management port is connected, and the link is good. Off There is no link to the management port. Green/Steady The management port is operating at 100 Mb/s. Off The management port is operating at 10 Mb/s. Utilization % (8 LEDs) Green The number of lit LEDs indicates the level of CPU activity.
LEDs Passport 8132TX and 8148TX I/O Modules The Passport 8132TX and 8148TX modules have three LEDs to indicate module and system operating conditions (Table B-2). In addition, each port has two LEDs to indicate data speed and link status (Table B-3). Figure B-2 shows the locations of the LEDs. 1 2 3 9120EA 1 = Module LEDs 2 = Port LEDs: Speed 3 = Port LEDs: Link/Activity Figure B-2.
Using the Passport 8100 Modules Table B-2 describes the module LEDs, and Table B-3 describes the port LEDs. Table B-2. Module LEDs on the Passport 8132TX and 8148TX Modules Label Color/State Meaning Fault Yellow/Steady A diagnostics failure or hardware failure has been detected. Yellow/Blinking A chassis failure has been detected. Off The system is functioning normally. Green/Steady This module is properly generating the system clock for the switch.
LEDs 8108GBIC 1 8 1 2 3 4 5 6 7 8 Fault Link Act Master Online 1 2 9682EA 1 = Module LEDs 2 = Port Link and Activity LEDs Figure B-3. Table B-4. LEDs on the Passport 8108GBIC Module Module LEDs on the Passport 8108GBIC Module Label Color/State Meaning Fault Yellow/Steady A diagnostics failure or hardware failure has been detected. Yellow/Blinking A chassis failure has been detected. Off The system is functioning normally.
Appendix C Media Dependent Adapters This appendix describes the media dependent adapters (MDAs) that are available from Nortel Networks. The MDAs can support high-speed connections to servers, shared Fast Ethernet hubs, or backbone devices.
Using the Passport 8100 Modules 450 Series MDAs Four versions of gigabit Ethernet MDAs are available: • Two shortwave gigabit MDAs (Figure C-1): — The 450-1SR MDA is a single-MAC MDA with a separate redundant Phy (backup Phy port). — The 450-1SX MDA is a single-Phy MDA. These MDAs use shortwave 850 nm fiber optic connectors to connect devices over multimode (550 meter) fiber optic cable.
Media Dependent Adapters 450-1LX MDA (single port) 450-1LR MDA (1-port redundant) 1000BASE-LX 1000BASE-LX 1000BASE-LX Link Link Phy Select Phy Activity Activity TX RX TX RX TX 450-1LR MDA 2 1 RX 450-1LX MDA 2 1 9216EA 1 = LEDs 2 = 1000BASE-FX SC Port Connectors Figure C-2. 1000BASE-LX (Longwave Gigabit) MDA Front Panels Table C-1 describes the 1000BASE-SX MDA LEDs. Table C-1.
Using the Passport 8100 Modules Table C-2 describes the 1000BASE-LX MDA LEDs. Table C-2. 1000BASE-LX MDA LEDs Label Type Color/State Meaning Link Communication link LEDs Green/On A valid communication link is established. Green/ Blinking The corresponding port is management disabled. Off The communication link connection is bad, or there is no connection to this port. Phy Select Phy selection LEDs Green/On The corresponding Phy port is selected.
Media Dependent Adapters Table C-3 shows the 8100-4TX MDA LEDs. Table C-3. 8100-4TX MDA LEDs Label Type 100 100BASE-TX port status Green/On LEDs Green/Blinking 10 F Dx Activity Color/State Meaning The corresponding port is set to operate at 100 Mb/s. The corresponding port is management disabled. Off The link connection is bad, or there is no connection to this port. Green/On The corresponding port is set to operate at 10 Mb/s. Green/Blinking The corresponding port is management disabled.
Using the Passport 8100 Modules 8100-2FX MDA (2-port SC connectors) 100BASE-FX 8100-4FX MDA (4-port MT-RJ connectors) 100BASE-FX Link TX RX TX RX Link F Dx F Dx Activity Activity 8100-2FX MDA 1 2 8100-4FX MDA 1 2 9214EB 1 = LEDs 2 = 100BASE-FX SC Port Connectors Figure C-4. 8100 Series MDA Front Panels Table C-4 describes the 8100 Series MDA LEDs. Table C-4.
Media Dependent Adapters Installing an MDA The MDA slot on the Passport 8132TX module accommodates a single MDA. The connection can be either an RJ-45 10/100BASE-TX MDA or a fiber (100BASE-FX or 1000BASE-SX/LX) MDA with an SC or MT-RJ connector. Note: The MDAs are hot-swappable in an operating Passport 8132TX module; however, the module resets when an MDA is inserted or removed. To install an MDA: 1. Loosen the retaining screw at each end of the module. 2.
Using the Passport 8100 Modules 5. Press the MDA firmly into the slot. Be sure that the MDA is fully seated into the mating connector. 6. Secure the MDA in the module by tightening the thumbscrews on the MDA front panel. 7. Use the inserter/extractor levers to reseat the module backplane connector. 8. Tighten the module retaining screws. 9. Attach devices to the MDA ports. Note: The IEEE 802.
Appendix D Installing GBICs This appendix describes how to install the gigabit interface converters (GBICs) in the Passport 8108GBIC module.
Using the Passport 8100 Modules Installing a GBIC The Passport 8108GB module has eight bays for installing GBICs. The GBIC bays are covered by spring-loaded filler panels that rotate out of the way as you push the GBIC into place. You can install or replace a GBIC in an operating switch module without powering down the switch. Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port.
Installing GBICs To remove an installed GBIC: 1. If the GBIC has spring tabs, press in on the tabs on each side of the GBIC as you pull the GBIC out of the bay (Figure D-3). 9704FA Figure D-3. 2. 204515-C Removing a GBIC If the GBIC has an extractor handle, grasp the handle and pull firmly to remove the GBIC from the bay.
Appendix E RFCs and Standards For more information about networking concepts, protocols, and topologies, you may want to consult the following sources: 204515-C • RFC 951 (BootP) • RFC 1112 (IGMP version 1) • RFC 1213 (Network Management of TCP/IP MIB II) • RFCs 1271 and 1757 (RMON) • RFC 1493 (Bridge MIB) • RFC 1573 (IANA If Type) • RFC 1643 (Ether-like MIB) • RFC 1723 (RIP version 2) • RFC 1850 (OSPF MIB) • RFC 2131 (DHCP) • RFC 2233 (IANA If Type) • RFC 2236 (IGMP version 2) •
Index Numbers 10/100 LED, B-4 C 10/100 Mb/s ports, 1-11 1000BASE-SX MDA 450-1SR MDA, C-2 450-1SX MDA, C-2 cable Category 5, 4-4 crossover, 4-4, A-12 fiber, 4-5 fiber optic, A-6 straight-through, 2-6, 4-4, A-5 troubleshooting, 4-4 UTP, A-6, A-8 1000BASE-XD GBIC, A-11 cable lengths, 2-6 1000BASE-ZX GBIC, A-11 cables, connecting, 2-6 100BASE-FX MDA, troubleshooting, 4-5 chassis configuration requirements, 2-2 8100 series MDAs, C-4 chassis slots, dedicated, 2-2 100 LED, B-2 1000BASE-LX GBIC, A-10
D I Declaration of Conformity, A-13 identification parameters, system, 3-5 default route, assigning, 3-9 IGMP, 1-3 defaults factory settings, 2-7 login names and passwords, 3-4 installation process, 2-3 troubleshooting, 4-7 Device Manager, 1-16 IP address assigning, 3-5, 3-8 troubleshooting, 4-7 DTE/DCE switch, 1-6, 4-2, A-4 duplex mode, troubleshooting, 4-5 E electromagnetic emissions, A-3 electrostatic discharge precautions, 2-2 L layer 2 read-write security access, 3-4 layer 2 switching, 3-8
Master LED, B-2, B-4 MDAs gigabit Ethernet, C-2 installing, C-7 versions, 1-9, C-1 MDI connections MDI-X to MDI, A-12 MDI-X to MDI-X, A-13 Console port, A-5 Ethernet Management port, A-4 mini-DIN connector, A-7 Modem port, A-5 port connections, troubleshooting, 4-4 port mirroring, 1-3 port numbers, 3-2 MLT, 1-3 ports 10/100 Mb/s, 1-11, A-6, A-8 autosensing, 1-8 Console, A-4 Ethernet Management, 1-5, A-4 MDI-X/MDI connections, A-12 Modem, A-5 serial, 1-6 Modem port, 1-6, A-5 power configuration, nonredu
restrictions dual power supplies, 2-5 port lists, 3-2 RFCs, E-1 RJ-45 connectors, 1-11 RMON, 1-3 routing switch modules, 1-16 S safety agency approvals, A-2 security levels, descriptions, 3-4 serial ports, 1-6 shortwave gigabit MDAs, C-2 slots, chassis, 2-2 SNMP, 1-4 SNMP community strings, changing, 3-6 T tagging, 1-3 technical publications, xviii technical support, xix Telnet access, 3-7 Temp LED, B-2 text conventions, xvi troubleshooting cables, 4-4 installation issues, 4-7 MDI and MDI-X connections, A
