User manual

ManualsBrandsNortel Networks ManualsOtherTelephone 1000E

Nortel Communication Server 1000

Nortel Communication Server 1000 Release 5.0

Communication Server 1000E

Installation and Commissioning

Document Number: NN43041-310

Document Release: Standard 01.11

Date: October 2008

Year Publish FCC TM

Produced in Canada

The information in this document is subject to change without notice. The statements, configurations, technical

data, and recommendations in this document are believed to be accurate and reliable, but are presented

without express or implied warranty. Users must take full responsibility for their applications of any products

specified in this document. The information in this document is proprietary to Nortel Networks.

Nortel, Nortel (Logo), the Globemark, SL-1, Meridian 1, and Succession are trademarks of Nortel Networks.

Title page

Summary of content (468 pages)

PAGE 1
Title page Nortel Communication Server 1000 Nortel Communication Server 1000 Release 5.0 Communication Server 1000E Installation and Commissioning Document Number: NN43041-310 Document Release: Standard 01.11 Date: October 2008 Year Publish FCC TM Copyright © 2008, Nortel Networks. All rights reserved. Produced in Canada The information in this document is subject to change without notice.
PAGE 2
PAGE 3
12 Page 3 of 466 Contents List of Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 How to get help . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Getting help from the Nortel Web site . . . . . . . . . . . . . . . . . . . . . . . . . 23 Getting help over the telephone from a Nortel Solutions Center . . . . . 23 Getting help from a specialist by using an Express Routing Code . . . .
PAGE 4
Page 4 of 466 NN43041-310 Contents Using telephones .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Installation summary . . . . . . . . . . . . . . . . . . . . . . . 35 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Introduction .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Installation tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Contents Page 5 of 466 Rack-mounting a Media Gateway or Media Gateway Expander . . . . . 84 Rack-mounting a Terminal Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Rack-mounting a BayStack 470 Switch . . . . . . . . . . . . . . . . . . . . . . . . 90 Rack-mounting a BayStack 460 Power over Ethernet unit .. . . . . . . . . 90 Installing system grounds . . . . . . . . . . . . . . . . . . . 91 Contents .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
Page 6 of 466 Contents Configuring initial IP configuration data on MGC .. . . . . . . . . . . . . . . 143 Configuring the CS 1000E CP PM Call Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Introduction .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Configuring login IDs and passwords . . . . . . . . . . . . . . . . .
PAGE 7
Contents Page 7 of 466 Verifying a successful configuration .. . . . . . . . . . . . . . . . . . . . . . . . . . 237 Testing the Leader Signaling Server . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Configuring the IPMG . . . . . . . . . . . . . . . . . . . . . . . 239 Contents .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Configuring the IPMG in Element Manager .. . . . . . . . . . . . . . . . . . . .
PAGE 8
Page 8 of 466 Contents Configuring a terminal and SDI ports . . . . . . . . . . 279 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Introduction .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Setting the TTY terminal port .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Traditional terminal SDI connection . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
Contents Page 9 of 466 Saving configuration changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Installing a CompactFlash .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Installing a card in a Media Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Verifying a card .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Disabling a card .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
Page 10 of 466 Contents Installing Line cards and cross-connecting telephones . . . . . . . . . . . . . . . . 379 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Introduction .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Card placement in a Media Gateway or a Media Gateway Expansion . 382 Cross-connecting telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 11
Contents Page 11 of 466 Installing and cross-connecting a Power Fail Transfer Unit . . . . . . . . . . . . . . . . . . . . . 437 Contents .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 Installing and connecting a QUA6 PFTU . . . . . . . . . . . . . . . . . . . . . . . 438 Installing and connecting a third-party PFTU .. . . . . . . . . . .
PAGE 12
Page 12 of 466 NN43041-310 Contents Standard 01.
PAGE 13
20 Page 13 of 466 List of Procedures Procedure 1 Removing the cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Procedure 2 Rack-mounting a Media Gateway or Media Gateway Expander . . . . . . 86 Procedure 3 Installing an NTBK80 Ground Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Procedure 4 Installing an NTDU6201 Ground Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
Page 14 of 466 List of Procedures Procedure 14 Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter . . . . . . . . . . 113 Procedure 15 Connecting a Media Card to the ELAN subnet . . . . . . . . . . . . . . . . . . . . 114 Procedure 16 Connecting a Media Card to the TLAN subnet . . . . . . . . . . . . . . . . . . . . 115 Procedure 17 Connecting a Media Gateway to a Media Gateway Expansion . . . . . . . 115 Procedure 18 Installing the software on the CP PM Call Server . . . . . . . . . . . . . . . . . .
PAGE 15
List of Procedures Page 15 of 466 Procedure 32 Configuring pseudo-terminals (PTYs) . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Procedure 33 Checking PTY status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Procedure 34 Configuring MG 1000E Bandwidth Management Zone . . . . . . . . . . . . . 161 Procedure 35 Launching Element Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Procedure 36 Importing an existing node . . . . .
PAGE 16
Page 16 of 466 List of Procedures Procedure 49 Configure conference TDS (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Procedure 50 Configuring conference TDS (Element Manager) . . . . . . . . . . . . . . . . . . 245 Procedure 51 Configure DSP Daughterboard Voice gateway channels (CLI) . . . . . . . 248 Procedure 52 Connecting a Terminal Server to the system . . . . . . . . . . . . . . . . . . . . . 254 Procedure 53 Configure IP address for the Terminal Server . . . . . . . . . . .
PAGE 17
List of Procedures Page 17 of 466 Procedure 67 Adding a Voice Gateway Media Card to an IP telephony node . . . . . . . 319 Procedure 68 Adding voice gateway channels using Element Manager . . . . . . . . . . . 323 Procedure 69 Configuring voice gateway channels using LD 14 . . . . . . . . . . . . . . . . . 326 Procedure 70 Installing the CompactFlash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 Procedure 71 Installing a Voice Gateway Media Card in a card slot . . . . . . . . .
PAGE 18
Page 18 of 466 List of Procedures Procedure 85 Importing an existing node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 Procedure 86 Reviewing and submitting IP telephony node configuration . . . . . . . . 370 Procedure 87 Adding a Follower Signaling Server to the IP telephony node in Element Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Procedure 88 Performing a datadump using Element Manager . . . . . . . . . . . . . . .
PAGE 19
List of Procedures Page 19 of 466 Procedure 102 Configuring the IP Softphone 2050 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 Procedure 103 Installing the USB Headset Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434 Procedure 104 Installing the IP Softphone 2050 on your PC . . . . . . . . . . . . . . . . . . . . . 434 Procedure 105 Displaying registered IP Phones in Element Manager . . . . . . . . . . . . . .
PAGE 20
Page 20 of 466 NN43041-310 List of Procedures Standard 01.
PAGE 21
22 Page 21 of 466 Revision history October 2008 Standard 01.11. This document is up-issued to reflect changes in technical content for CR Q01945162. October 2008 Standard 01.10. This document is up-issued to reflect changes in digital trunk cards and system components sections. October 2008 Standard 01.09. This document is up-issued to reflect changes in technical content. September 2008 Standard 01.08. This document is up-issued to reflect changes in technical content. August 2008 Standard 01.06.
PAGE 22
Page 22 of 466 Revision history June 2007 Standard 01.03. This document is up-issued with corrections from CR Q001646756. May 2007 Standard 01.02. This document is up-issued with corrections from CR Q001646756. May 2007 Standard 01.01. This document is up-issued for Communication Server 1000 Release 5.0. This document contains information previously contained in the following legacy document, now retired: Communication Server 1000E: Installation and Configuration (553-3041-210). July 2006 Standard 3.
PAGE 23
24 Page 23 of 466 How to get help This section explains how to get help for Nortel products and services. Getting help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: www.nortel.com/support This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products.
PAGE 24
Page 24 of 466 How to get help Outside North America, go to the following Web site to obtain the phone number for your region: www.nortel.com/callus Getting help from a specialist by using an Express Routing Code To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: www.nortel.
PAGE 25
26 Page 25 of 466 Finding the latest updates on the Nortel web site The content of this documentation was current at the time the product was released. To check for updates to the latest documentation and software for CS 1000 Release 5.0, click one of the links below. Latest Software Takes you directly to the Nortel page for CS 1000 Release 5.0 software. Latest Documentation Takes you directly to the Nortel page for CS 1000 Release 5.0 documentation.
PAGE 26
Page 26 of 466 NN43041-310 Finding the latest updates on the Nortel web site Standard 01.
PAGE 27
30 Page 27 of 466 System information This document is a global document. Contact your system supplier or your Nortel representative to verify that the hardware and software described are supported in your area. Subject This document provides the information necessary to install and configure a Nortel Networks Communication Server 1000E system. WARNING Before a CS 1000E system can be installed, a network assessment must be performed and the network must be VoIP-ready.
PAGE 28
Page 28 of 466 System information Technical Documentation link under Support & Training on the Nortel home page: www.nortel.com Applicable systems This document applies to the Communication Server 1000E (CS 1000E) system. Note: When upgrading software, memory upgrades may be required on the Signaling Server, the Call Server, or both. Conventions In this document, the CS 1000E system is referred to generically as “system.
PAGE 29
System information Page 29 of 466 • Element Manager: System Administration (NN43001-632) • IP Line: Description, Installation, and Operation (NN43100-500) • Telephones and Consoles: Description, Installation, and Operation (NN43001-567) • IP Phones: Description, Installation, and Operation (NN43001-368) • Software Input/Output: Maintenance (NN43001-711) • ISDN Primary Rate Interface: Maintenance (NN43001-717) • ISDN Basic Rate Interface: Maintenance (NN43001-718) • Communication Server 1000
PAGE 30
Page 30 of 466 NN43041-310 System information Standard 01.
PAGE 31
34 Page 31 of 466 Safety instructions Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Lifting system equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Handling circuit cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Installing telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 32
Page 32 of 466 Safety instructions Lifting system equipment Care should be exercised when lifting system components. If necessary, get assistance to lift a component or install a component in a rack. The weight of the system component can be found in the component profiles in “System components” on page 39. Before lifting or installing a component: • Ensure that the planned location and the route to that location are free of obstacles and debris.
PAGE 33
Safety instructions Page 33 of 466 Installing telephones Follow these safety instructions when installing telephone equipment: • Never install telephone wiring during a lightning storm. • Never install a telephone jack in wet locations unless the jack is designed for wet locations. • Never touch an uninsulated telephone wire or terminal unless the telephone line is disconnected at the network interface. • Use caution when installing or modifying telephone lines.
PAGE 34
Page 34 of 466 Safety instructions • Some equipment has a three-wire grounding plug. This type of plug has a third grounding pin. As a safety feature, the plug only fits into an isolated ground outlet. If you cannot insert the plug completely into the outlet, contact your electrician to replace the outlet. • Some equipment has a polarized line plug. This type of plug has one blade wider than the other. As a safety feature, this plug fits into the power outlet one way.
PAGE 35
38 Page 35 of 466 Installation summary Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Installation tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Introduction WARNING Before a CS 1000E system can be installed, a network assessment must be performed and the network must be VoIP-ready.
PAGE 36
Page 36 of 466 Installation summary the CS 1000E system, see “Installing and configuring Nortel IP Phones” on page 391. Installation tasks Table 1 lists the tasks involved with the installation of a CS 1000E system.
PAGE 37
Installation summary Page 37 of 466 Table 1 List of required installation tasks (Part 2 of 2) Task Go to page Installing and cross-connecting a Power Fail Transfer Unit 437 Installing and cross-connecting an external alarm from a PFTU 451 Basic system telephony configuration 457 Configuring IP Peer Networking and managing the Gatekeeper database 463 Communication Server 1000E Installation and Commissioning
PAGE 38
Page 38 of 466 NN43041-310 Installation summary Standard 01.
PAGE 39
80 Page 39 of 466 System components Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CS 1000E Common Processor Pentium Mobile Call Server . . . . . . . . 43 Signaling Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Media Gateway Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 MC32S Media Card .
PAGE 40
Page 40 of 466 System components Introduction Supported configurations The following CS 1000E system configurations for CS 1000 Release 5.
PAGE 41
System components • 19-inch rack • Uninterruptible Power Supply (UPS) Page 41 of 466 CS 1000E High Availability (redundant) The CS 1000E High Availability system consists of the following components: • Dual CP PM Call Servers • Dual CP PM Signaling Servers • MC32S Media Card • Media Gateway Controller • DSP Daughterboard • Media Gateway • Media Gateway Expander • BayStack 470 Switch • MRV Terminal Server • System cables Note: You must order the power cord specified for your region
PAGE 42
Page 42 of 466 System components • Media Gateway Expander • BayStack 470 Switch • MRV Terminal Server • System cables The system uses the following customer-supplied components: • BayStack 460 Layer 2 switch • 19-inch rack • Uninterruptible Power Supply (UPS) Note: You must order the power cord specified for your region CS 1000E Cabinet option The CS 1000E Cabinet system consists of the following components: • Single or Dual CP PM Call Servers • Single or Dual CP PM Signaling Servers •
PAGE 43
System components Page 43 of 466 Note: For all configurations, a COTS Signaling Server may be an option. CS 1000E Common Processor Pentium Mobile Call Server The Common Processor Pentium Mobile (CP PM) is a high performance server that can act as either a Call Server or a Signaling Server in a CS 1000E system. There are two CP PM types available for CS 1000 Release 5.0: NTDW61BA and NTDW66AAE5.
PAGE 44
Page 44 of 466 System components Figure 1 CS 1000E CP PM Call Server NN43041-310 Standard 01.
PAGE 45
System components Page 45 of 466 Figure 2 CS 1000E CP PM Call Server (side view) Choosing the cabinet and slot location for the CP PM card An MG 1000E performs functions under the control of the CS 1000E Core CP PM Call Server. Traditionally, in CS 1000 Release 4.5, this core CP PM Call Server was a CP PII or CP PIV processor in its own Call Server chassis.
PAGE 46
Page 46 of 466 System components For CS 1000 Release 5.0, the CP PM call server processor sits in one of the slots in the MG1000E chassis. The CP PM Call Server processor connects to the MG 1000E Media Gateway Controllers via Ethernet and therefore does not require backplane connectivity (other than power and slot ID). The following rules apply to the preferential placement of the CP PM call server in the MG 1000E: • The CP PM call server processor must not be installed in slot 0 of any MG 1000E.
PAGE 47
System components Page 47 of 466 Figure 3 CS 1000E CP PM Call Server system overview CP-PM Faceplate Components The following section details the CP PM faceplate. Refer to Figure 4 on page 50.
PAGE 48
Page 48 of 466 System components • Green: Normal Operation • Flashing Green: SL1 Loading (on Active Core only) • Off No Power Call Server Redundancy LED • Green: Redundant Mode, Active • Flashing Green: Split Mode, Active • Yellow: Redundant Mode, Standby • Flashing Yellow: Split Mode, Standby • Red: Single Mode • Off Not implemented Ethernet Interface LEDs ELAN RJ45 left: • Green: Link Up • Blink Green: Link Up & Activity • Off: No Link ELAN RJ45 right: • Off: 10 Mbps • Yellow:
PAGE 49
System components Page 49 of 466 HSP RJ45 right • Off: 10 Mbps • Yellow: 100 Mbps • Green: 1000 Mbps Compact Flash/ Hard Disk LEDs • CF - Flashing Green shows activity on RMD • HD/CF – Flashing Green shows activity on FMD (or HD for CP PM Signaling Server) Faceplate Push Buttons • RST: Cold Start / SysLoad • INI: Warm Start / INI Communication Server 1000E Installation and Commissioning
PAGE 50
Page 50 of 466 System components Figure 4 CS 1000E CP PM Call Server CP PM CS Serial Data Interface (SDI) The CP PM Call Server features two standard RS232 DTE serial ports, port 0 and port 1. These ports are accessible through a cable that attaches to the chassis or cabinet MDF port. NN43041-310 Standard 01.
PAGE 51
System components Page 51 of 466 The TTY Settings are: • Baud Rate: 9600 • Data bit: 8 • Stop bit: 1 • Parity: None • Flow Control: None CP PM Call Server Switch Settings The CP PM Call Server switch S5 must be set to position 1 to indicate that a CF card is used for the FMD. The CP-PM Signaling Server switch S5 must be set to position 2 to indicate that a hard disk is used for the FMD.
PAGE 52
Page 52 of 466 System components IMPORTANT! The RMD used for installation must be created specifically for CP PM using the mkbootrmd utility provided in the CP PM Call Server install zip file. An RMD created using the CP PIV mkbootrmd utility will not work on a CP PM Call Server installation. CP PM hardware requires different bootrom.sys and nvram.sys files than CP PIV due to the differences in the processor chipset used on the two platforms.
PAGE 53
System components Page 53 of 466 The ISP1100 Signaling Server, as shown in Figure 5 and described in Table 2, provides signaling interfaces to the network using software components that run on a real-time operating system. You can install ISP1100 Signaling Servers in a load-sharing redundant configuration for higher scalability and reliability. The ISP1100 Signaling Server is equipped with several software components: • IP Phone Terminal Proxy Server (TPS) • H.
PAGE 54
Page 54 of 466 System components Table 2 ISP1100 Signaling Server profile (Part 2 of 3) Property Description Power • Power status indicator (green LED) is located on the unit’s faceplate. • Power cord connector is located on the left-hand corner on the back of the unit. • Power On/Off switch is on the faceplate. • Power supplies are factory installed and not customer replaceable. • Unit is AC powered (100-240 VAC); DC input is not supported. Cooling • Forced air cooling with front-to-back air flow.
PAGE 55
System components Page 55 of 466 Table 2 ISP1100 Signaling Server profile (Part 3 of 3) Property Description Connectors (front) • The DB-9 serial port, the CD-ROM and floppy drives are located on the unit’s faceplate. • The DB-9 serial port can support a login session for Command Line Interface (CLI) management. • See Figure 6 on page 56. Connectors (rear) • The TLAN network interface (P2) connects the unit to a TLAN network interface on a Layer 2 Switch.
PAGE 56
Page 56 of 466 System components Figure 6 Connectors on the front of the ISP1100 Signaling Server CD-ROM and floppy Maintenance port drives NN43041-310 Standard 01.
PAGE 57
System components Page 57 of 466 Figure 7 Connectors at the back of the ISP1100 Signaling Server not used Universal AC power cord connector not used TLAN (P2) not used ELAN (P1) Maintenance/ Admin port CP PM Signaling Server The CP PM Signaling Server is in the form of a circuit card and comes in two distinct models, NTDW61 and NTDW66. The NTDW61 model is designed for use in a CS 1000E system and the NTDW66 model is designed for use in a CS 1000M system.
PAGE 58
Page 58 of 466 System components Keying will prevent the NTDW61 circuit card from being inserted into this slot. CAUTION — Equipment Damage Do not insert the NTDW61 model of the CP PM Signaling Server circuit card into any slot of an IPE cube. Doing so may cause electrical shorts on adjacent circuit cards. For detailed Signaling Server information, see “Installing a Signaling Server” on page 173.
PAGE 59
System components Page 59 of 466 daughterboard. These daughterboards provide DSP resources for connecting IP and TDM devices, eliminating the need for installing Voice Gateway Media Cards on the CS 1000E Media Gateways. However, Voice Gateway Media Cards are still supported in CS 1000E. MC32S Media Card The MC32S is a 32-channel Voice Gateway Media Card that provides 32 Digital Signal Processor (DSP) ports to facilitate connectivity between IP and TDM devices.
PAGE 60
Page 60 of 466 System components Table 3 Media Card profile (Part 2 of 2) Property Description Cooling • Provided by the Media Gateway or Media Gateway Expander. Connectors (front) • The PC Card slot can be used to deliver software or for additional storage. • The maintenance port provides access to the card for OA&M purposes. • This port cannot be used for installation. • This port does not display bootup messages and the user cannot change boot parameters using this port.
PAGE 61
System components Page 61 of 466 Figure 8 Media Card PC Card slot Maintenance port Media Gateway The media gateway is shown in Figure 9 on page 62 and described Table 4 on page 62.
PAGE 62
Page 62 of 466 System components Figure 9 5-pair Cable Connectors on the Media Gateway Car d 4 25-pair connectors Card 3 Card 2 Ca r d 1 CAUTION — Damage to Equipment Do not block equipment ventilation openings. Table 4 Media Gateway profile (Part 1 of 3) NN43041-310 Property Description Product Code • NTDU14 Height • less than 5 U (1 U = 1 3/4 inch or 4.4 cm) Standard 01.
PAGE 63
System components Page 63 of 466 Table 4 Media Gateway profile (Part 2 of 3) Property Description Power • Power status indicator (Nortel logo) is located on the unit faceplate. • Power cord connector is located on the right rear when viewed from the front. • Power On/Off switch is located behind the faceplate. See Figure 10 on page 66. • Power supplies are factory installed and not customer replaceable. • Unit is AC powered (100-240 VAC); DC is not supported.
PAGE 64
Page 64 of 466 System components Table 4 Media Gateway profile (Part 3 of 3) Property Description Connectors (rear) • The 25-pair cable connectors at the back panel (see Figure 9 on page 62) provide access to the cross-connect terminal (Main Distribution Frame). • The AUX port connects a Power Failure Transfer Unit (PFTU) to the Media Gateway. • The Attachment Unit Interface (AUI) is used with earlier version SSC which require a Media Access Unit (MAU).
PAGE 65
System components Page 65 of 466 Figure 7 Connectors at the back of the Media Gateway Universal AC power cord connector Call Server to Media Gateway link AUX 2 1 GND SDI Port Port 2 AUI DS-30X CE-MUX Communication Server 1000E Installation and Commissioning
PAGE 66
Page 66 of 466 System components Figure 10 Front of the Media Gateway DIP switch settings Power status indicators Power switch Bulkhead connectors NN43041-310 Standard 01.
PAGE 67
System components Page 67 of 466 Media Gateway Expander Figure 11 on page 67 shows the Media Gateway Expander and Table 5 on page 67 describes the expander. Figure 11 Media Gateway Expander SLOT 10 SLOT 9 SLOT 8 SLOT 7 Slot 10 Slot 9 Slot 8 Slot 7 553-CSE9032 Table 5 Media Gateway Expander profile (Part 1 of 3) Property Description Order Code • NTDU15 Height • less than 5 U (1 U = 1 3/4 inch or 4.
PAGE 68
Page 68 of 466 System components Table 5 Media Gateway Expander profile (Part 2 of 3) Property Description Power • Power status indicator (Nortel logo) is located on the unit’s faceplate. • Power cord connector is located on the right rear when viewed from the front. • Power On/Off switch is located behind the faceplate. See Figure 10 on page 66. • Power supplies are factory installed and not customer replaceable. • Unit is AC powered (100-240 VAC); DC is not supported.
PAGE 69
System components Page 69 of 466 Table 5 Media Gateway Expander profile (Part 3 of 3) Property Description Card slots • Four usable universal card slots: 7 to 10. See Figure 11 on page 67. • Logical slots 5 and 6 are not supported.
PAGE 70
Page 70 of 466 System components Figure 12 Connectors at the back of the Media Gateway Expander Universal AC power DS-30X CE-MUX cord connector Ca 10 d 9 rd Car C ar d 8 Ca rd 7 25-pair connectors 19-inch Rack Mount Kit A 19-inch Rack Mount Kit (NTTK09AA) is available for mounting a Media Gateway and Media Gateway Expander in a 19-inch rack.
PAGE 71
System components Page 71 of 466 Table 6 NTTK09AA installation Order Code Description Qty P0906672 Left Shelf Mounting Bracket U/O 1 P097F813 Screw, .216- 24 X .500 STL 289A 8 P0719943 Sems, Ext Tooth Washer Pan Head, CR Type1A, 0.164- 32 X 4 P0906671 Right Shelf Mounting Bracket U/O 1 P0719587 Sems, Ext Tooth Washer Pan Head, CR Type 1A, 0.
PAGE 72
Page 72 of 466 System components Table 7 BayStack 470 Switch profile (Part 2 of 2) Property Description Cooling • Forced air cooling with side-to-side air flow. • The three fans run whenever the unit is on. Card slots • None Connectors (front) • Unit is DCE for serial port connection to PC; requires null modem for Terminal Server connection. • Console port default settings: 9600 baud with 8 data bits, 1 stop bit, and no parity as the communications format, with flow control set to enabled.
PAGE 73
System components Page 73 of 466 A third-party data network switch can be used with the system. For more information, refer to Converging the Data Network with VoIP (NN43001-260). BayStack 460 Layer 2 switch The BayStack 460 Layer 2 switch, shown in Figure 14 on page 73, adds power in addition to data communications over standard Category 5 LAN drops for powering the IP Phones.
PAGE 74
Page 74 of 466 System components The Terminal Server is configured to automatically log in to the active Core CP PM Call Server upon start-up. It always connects to the Active CPU IP address. The CS 1000E can configure up to 16 serial ports for applications within the configuration Data Block. Ports can be configured by using: • login userid of "PTYnn" – TTY ports are specified where nn is the PTY port number configured for a particular TTY within LD 17.
PAGE 75
System components Page 75 of 466 Table 8 MRV IR-8020M Terminal Server profile (Part 2 of 2) Property Description Power • Power cord connector is located on the left-hand corner on the unit’s backplane. • Power supplies are factory installed and not customer replaceable. • Unit is AC powered (120 V AV @ 1.58 amps). Cooling • Forced air cooling with side-to-side air flow. • The fans run at a single speed. • Ensure that equipment ventilation openings are not blocked.
PAGE 76
Page 76 of 466 System components Table 9 CS 1000E cables (Part 1 of 2) Component Descriptions Cable Kits Cables & Accessories Quantity Qty of 2 MRV Terminal Server cables for connecting COM port 1 of the CP PM Call Server to the Terminal Server NTDU6302 2 HS cross-over cable used to connect the two call processors for redundancy.
PAGE 77
System components Page 77 of 466 Table 9 CS 1000E cables (Part 2 of 2) Component Descriptions Cable Kits Cables & Accessories Quantity 100BaseT Connection Signaling Servers, Layer two switch (BS 470), Carrier Cards, ELAN on Gateways CAT5 Cables MRV Terminal Server RJ45 to 9-pin female RS232, 25 feet long, for connecting terminal equipment to the MRV Terminal Server Terminal server cable kit for interfacing with various terminal ports (that is, Signaling Server, Baystack or Gateway using BK48 cable)
PAGE 78
Page 78 of 466 System components Miscellaneous system components Table 10 contains a list of miscellaneous items that can be used with the CS 1000E system installation.
PAGE 79
System components Page 79 of 466 A UPS provides a continuous AC power supply. Refer to Communication Server 1000E: Planning and Engineering (NN43041-220) for calculating power consumption requirements. Install the UPS unit according to the manufacturer’s instructions.
PAGE 80
Page 80 of 466 NN43041-310 System components Standard 01.
PAGE 81
90 Page 81 of 466 Rack-mounting the components Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Lifting system components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Guidelines for component placement in a rack. . . . . . . . . . . . . . . . . . . 83 Rack-mounting a Media Gateway or Media Gateway Expander . . . . .
PAGE 82
Page 82 of 466 Rack-mounting the components Note: In the 5u pattern, a “u” is equal to 1.75 in. and includes three holes spaced at 5/8 in. + 5/8 in. + 1/2 in. Other data communications equipment can be installed in a rack with CS 1000E system components. IMPORTANT! Ensure that the unit’s power cord is appropriate for the area’s electrical service. Do not modify or use the supplied AC power cord if it is not the correct type.
PAGE 83
Rack-mounting the components Page 83 of 466 Table 11 Weight of CS 1000E system components (Part 2 of 2) Component Lbs Kg Media Gateway Expander — without cards 26 12 — with 4 cards 30 13.5 BayStack 470 Switch 14.7 6.7 BayStack 460 Power over Ethernet Switch 12.76 5.8 11 5 MRV Terminal Server Guidelines for component placement in a rack When installing equipment, the Layer two switches should be in a central location to allow for easy access of all LAN cabling.
PAGE 84
Page 84 of 466 Rack-mounting the components Rack-mounting a Media Gateway or Media Gateway Expander References to the Media Gateway in this section also apply to the Media Gateway Expander. The Media Gateway Expander can be mounted either above or below the Media Gateway.
PAGE 85
Rack-mounting the components Page 85 of 466 upward to remove it from the Media Gateway. Refer to Figure 16 on page 86. Note: The bottom of the front cover is supported by, but not secured to, the Media Gateway. Do not drop it.
PAGE 86
Page 86 of 466 Rack-mounting the components Figure 16 Unlock the cover End of Procedure Procedure 2 Rack-mounting a Media Gateway or Media Gateway Expander 1 NN43041-310 Fasten the right guide bracket to the right rack support. a. Insert two #10-32 machine screws into the two middle slots in the guide bracket and into the respective holes in the right rack support. See Figure 17. b. Fasten the screws. Standard 01.
PAGE 87
Rack-mounting the components Page 87 of 466 Figure 17 Guide bracket installed in a rack #10-32 2 3 Fasten the left guide bracket to the left rack support. a. Insert two #10-32 machine screws into the two middle slots in the bracket and into the respective holes in the left rack support. b. Fasten the screws. Attach the right ear bracket (marked with an “R”) to the holes on the right side of the Media Gateway. a. Use two #8-32 machine screws.
PAGE 88
Page 88 of 466 Rack-mounting the components Figure 18 Right ear bracket on a Media Gateway Bracket flange marked with an “R”. Attach this ear bracket to the righthand side of the Media Gateway. Attach the ear bracket to these holes. 4 NN43041-310 Attach the left ear bracket (marked with an “L”) to the holes on the left side of the Media Gateway (near the front). Standard 01.
PAGE 89
Rack-mounting the components a. Page 89 of 466 Use two #8-32 machine screws. Position the ear bracket so the four holes on the bracket flange are closer to the rear of the Media Gateway. Note: To determine the front of the bracket, locate the “L” on the bracket. The “L” must be at the top of the bracket and face the front of the Media Gateway. WARNING A Media Gateway or a Media Gateway Expander each weighs approximately 30 lb. (13.5 kg) with circuit cards installed and 26 lb.
PAGE 90
Page 90 of 466 Rack-mounting the components Rack-mounting a Terminal Server Follow the manufacturer’s instructions to rack-mount this equipment. Rack-mounting a BayStack 470 Switch Follow the manufacturer’s instructions to rack-mount this equipment. Rack-mounting a BayStack 460 Power over Ethernet unit Follow the manufacturer’s instructions to rack-mount this equipment. NN43041-310 Standard 01.
PAGE 91
100 Page 91 of 466 Installing system grounds Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Installing a ground bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Grounding an ISP1100 Signaling Server . . . . . . . . . . . . . . . . . . . . . . . 95 Grounding a Media Gateway powered by the same electrical panel . .
PAGE 92
Page 92 of 466 Installing system grounds Refer to your grounding plan for additional information. WARNING Correct grounding is very important. Failure to complete the grounding procedures could result in a system that is unsafe for the personnel using the equipment. CAUTION — Service Interruption If your system is not grounded correctly, it cannot be protected from lightning or power surges, and it could be subject to service interruptions. You must use insulated ground wire for system grounding.
PAGE 93
Installing system grounds Page 93 of 466 Follow Procedure 3 to install a ground bar. Procedure 3 Installing an NTBK80 Ground Bar 1 Place the ground bar near the equipment. Note: The ground bar is a bridging point for ground wires from up to six components. 2 Connect the ground bar to the ground bus in the AC electrical panel using #6 AWG wire. See Table 12 on page 93 for region-specific grounding requirements.
PAGE 94
Page 94 of 466 Installing system grounds Figure 20 NTBK80 Ground Bar End of Procedure Follow Procedure 4 to install an NTDU6201 Ground Bar. Procedure 4 Installing an NTDU6201 Ground Bar 1 Place the NTDU6201 Ground Bar near the equipment. Note: The ground bar is a bridging point for ground wires from up to 48 components. NN43041-310 Standard 01.
PAGE 95
Installing system grounds 2 Page 95 of 466 Connect the NTDU6201 Ground Bar to the ground bus in the AC electrical panel, or to TGB for an ANSI/EIA/TIA 607 installation using #6 AWG wire. See Table 12 on page 93 for region-specific grounding requirements. WARNING A qualified technician or electrician must make the connection in the AC electrical panel. 3 Place a tag marked DO NOT DISCONNECT on the ground wire at the electrical panel. 4 Test the ground.
PAGE 96
Page 96 of 466 Installing system grounds Procedure 5 Grounding Media Gateways powered by the same electrical panel 1 Disconnect the AC power cord from the power outlet. 2 Install a #6 AWG ground wire from the ground lug, as shown in Figure 21 on page 96, at the back of the Media Gateway to the ground bar. 3 Place a DO NOT DISCONNECT tag on the ground wire.
PAGE 97
Installing system grounds 4 Page 97 of 466 Test the ground. End of Procedure Grounding a Media Gateway powered by multiple electrical panels Follow Procedure 6 on page 97 to ground multiple Media Gateway that are powered by multiple electrical panels. Procedure 6 Grounding Media Gateways powered by multiple electrical panels 1 Disconnect the AC power cord from the power outlet. 2 Identify the electrical panel powering each component. 3 Install a ground bar for each electrical panel identified above.
PAGE 98
Page 98 of 466 Installing system grounds IMPORTANT! Power each Media Gateway and Media Gateway Expander pair from the same electrical panel. Follow Procedure 7 to ground a Media Gateway Expander. Procedure 7 Grounding a Media Gateway Expander 1 Disconnect the AC power cord from the power outlet. 2 Install a #6 AWG ground wire from the ground lug on the rear of the Media Gateway Expander to the Media Gateway. See Figure 21 on page 96. 3 Place a DO NOT DISCONNECT tag on the ground wire.
PAGE 99
Installing system grounds Page 99 of 466 Figure 22 Grounding multiple pieces of equipment in a rack Terminal Server Signaling Server CS 1000E Call Server Media Gateway Chassis Grounding lug on back of chassis Media Gateway Chassis Expansion Other data communications equipment with grounding lug Rack grounding block NTBK80 or NTDU6201 Ground Bar 553-CSE9027C Communication Server 1000E Installation and Commissioning
PAGE 100
Page 100 of 466 Installing system grounds Grounding equipment in the UK Follow Procedure 8 to ground equipment in the UK. Procedure 8 Grounding equipment in the UK 1 Connect a protective and functional ground wire from the grounding strip on the Krone Test Jack Frame to the ground at the building entry point. Use a green/yellow wire no thinner than 10 mm2. Consider each Media Gateway and Media Gateway Expander pair as one ground. 2 Jumper the Media Gateway Expander ground to the Media Gateway ground.
PAGE 101
116 Page 101 of 466 Installing and connecting CS 1000E hardware Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Connecting CP PM Call Server 0 to CP PM Call Server 1. . . . . . . . . . 102 Installing the cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Cabling the cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 102
Page 102 of 466 Installing and connecting CS 1000E hardware • Procedure 10: "Connecting Campus Redundant CP PM Call Servers" on page 104 • Procedure 11: "Installing a DSP Daughterboard" on page 105 • Procedure 12: "Installing the MGC card" on page 105 • Procedure 13: "Installing the CP PM card" on page 106 • Procedure 14: "Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter" on page 113 • Procedure 15: "Connecting a Media Card to the ELAN subnet" on page 114 • Procedure 16: "Connecting a
PAGE 103
Installing and connecting CS 1000E hardware Page 103 of 466 For detailed information on Campus Redundancy, refer to Communication Server 1000: System Redundancy (NN43001-507). The Layer 2 switch allows the ELAN subnet and the subnet of the High Speed Pipe (HSP) to be extended between the two processors. The BayStack 470-24T provides full duplex wire-speed 100BaseT with no significant packet loss (less than 0.001%) and delays of less than 100 usec.
PAGE 104
Page 104 of 466 Installing and connecting CS 1000E hardware information, see Communication Server 1000: System Redundancy (NN43001-507). Procedure 10 Connecting Campus Redundant CP PM Call Servers 1 Connect the CAT5E RJ-45 LAN 2 port of Call Server 0 to a 100BaseT ELAN network interface on the local Baystack 470-24T switch. 2 Connect the CAT5E RJ-45 LAN 2 port of Call Server 1 to a 100BaseT port on the remote Baystack 470-24T switch.
PAGE 105
Installing and connecting CS 1000E hardware Page 105 of 466 Procedure 11 Installing a DSP Daughterboard 1 Place the MGC on a safe ESD surface. 2 Place the DSP DB in either DB position 1 (for DSP DB-96) or DB position 2 (for DSP DB-32), or both, depending on how the Daughterboards will be configured from a TN perspective. 3 Ensure the DSP DB is securely attached to the MGC (using the four supplied screws and standoffs). Note: Note: Call Server dongles do not need to be retained for IPMGs.
PAGE 106
Page 106 of 466 Installing and connecting CS 1000E hardware 5 The existing 3-port SDI cable (NTBK48AA) is reused. It connects to the SDI port on the Chassis. This chassis, the main chassis in the system, will now become known as IPMG 00. End of Procedure Installing the CP PM card The following procedure describes how to install the CP PM card in a Chassis. Note: Ensure that all DIP switches are set correctly. DIP switches determine whether the CP PM boots from a hard drive or compact flash.
PAGE 107
Installing and connecting CS 1000E hardware Page 107 of 466 Figure 23 2-port SDI cable (NTAK19EC) cable End of Procedure Cabling the cards The following sections describe the process required to cable the MGC and CP PM cards. Cabling the MGC The existing 3-port SDI cable (NTBK48AA) is reused. It connects to the SDI port on the Chassis. Figure 24 on page 109 shows front of MGC. The CE and CT ports are reserved for the CP PM card only.
PAGE 108
Page 108 of 466 Installing and connecting CS 1000E hardware port of the call server, while the CT connects to the TLAN port of the call server. The 1E and 2T ports must be attached to the layer 2 switch. MGC Ethernet Capabilities An MGC features six Ethernet interfaces set to auto-negotiate by default: four on the faceplate (see Figure 24 on page 109), and two on the back. Figure 25 on page 110, Figure 26 on page 111, and Figure 27 on page 112 illustrate the various ethernet connections.
PAGE 109
Installing and connecting CS 1000E hardware Page 109 of 466 Figure 24 MGC faceplate 1E: ELAN Dual homed with Backplane E CE: ELAN Dedicated for CPPM-CS CT: TLAN Dedicated for CPPM-CS 2T: TLAN Dual homed with Backplane T Note: The MG1000E can be connected directly to the CS1000E ELAN subnet, or it can be connected to the ELAN subnet through a Layer 2 switch.
PAGE 110
Page 110 of 466 Installing and connecting CS 1000E hardware Figure 25 Elan connection (CP PM Call Server) NN43041-310 Standard 01.
PAGE 111
Installing and connecting CS 1000E hardware Page 111 of 466 Figure 26 Elan connections (MGC) Communication Server 1000E Installation and Commissioning
PAGE 112
Page 112 of 466 Installing and connecting CS 1000E hardware Figure 27 Ethernet connections for CP PM Signaling Server Note: Refer to Figure 26 on page 111 for a visual representation of MGC card cabling (from port 1E and 2T) out to the layer 2 switch. Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter onto a Media Card The Shielded 50-pin to Serial/ELAN/TLAN adapter shown in Figure 28 provides access to the TLAN and ELAN Ethernet Ports.
PAGE 113
Installing and connecting CS 1000E hardware • TLAN (telephony) network interface • one RS-232 (local console) port Page 113 of 466 Figure 28 Shielded 50-pin to Serial/ELAN/TLAN adapter TLAN RJ-45 LAN socket ELAN RJ-45 LAN socket RS-232 Connector Voice Gateway Media Card maintenance port 50-pin connector Identification Label Procedure 14 Inserting a Shielded 50-pin to Serial/ELAN/TLAN adapter 1 Open the Media Card package NTDU41CA. 2 Remove the Shielded 50-pin to Serial/ELAN/TLAN adapter.
PAGE 114
Page 114 of 466 Installing and connecting CS 1000E hardware Connecting a Media Card to the ELAN subnet Follow Procedure 15 to connect a Media Card to the ELAN. Procedure 15 Connecting a Media Card to the ELAN subnet 1 Connect a standard CAT5 patch cable to the ELAN network interface on the Adaptor (Figure 29 on page 114).
PAGE 115
Installing and connecting CS 1000E hardware Page 115 of 466 Connecting a Media Card to the TLAN subnet Follow Procedure 16 to connect a Media Card to the TLAN subnet. Procedure 16 Connecting a Media Card to the TLAN subnet 1 Connect a standard CAT5 patch cable to the TLAN network interface on the adaptor (see Figure 29 on page 114). 2 Connect the other end of the standard CAT5 patch cable to an RJ-45 TLAN network interface on the BayStack 470 switch.
PAGE 116
Page 116 of 466 Installing and connecting CS 1000E hardware Figure 30 Media Gateway and Media Gateway Expander connections NTDK95 cables CE-MUX connector DS-30X connector End of Procedure NN43041-310 Standard 01.
PAGE 117
150 Page 117 of 466 Installing software on the CS 1000E Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Configuring initial IP configuration data on MGC . . . . . . . . . . . . . . . .
PAGE 118
Page 118 of 466 Installing software on the CS 1000E IMPORTANT! Systems and components delivered to customer sites may include preinstalled software. However, the pre-installed software versions are typically older and are included only for manufacturing and order management purposes. Do not attempt to operate the system with the pre-installed software. You must download the latest software from the Nortel Software Download web site and install the software as part of the installation process.
PAGE 119
Installing software on the CS 1000E Page 119 of 466 The VxWorks banner screen appears (see Figure 32 on page 119): Figure 32 VxWorks banner 4 Enter y for both software warnings to proceed with the upgrade. Note: PE/EPE is not applicable for this upgrade as it only applies to large systems.
PAGE 120
Page 120 of 466 Installing software on the CS 1000E 5 The Software Installation Tool Main Menu appears (see Figure 33 on page 120). Note: If the keycode files reside on a separate CF card, remove the software CF card and insert the CF card containing the keycode files. The keycode normally resides in the keycode folder of the OS CF card. Figure 33 Software Installation Tool Main Menu NN43041-310 Standard 01.
PAGE 121
Installing software on the CS 1000E Page 121 of 466 6 Enter or u to access the Install Menu. The following screen appears (see Figure 34). 7 The keycode file appears in the list. Select the appropriate keycode file for this system and install the keycode. Figure 34 Keycode files Note: If the CF card was exchanged, insert the CF card containing CS 1000 Release 5.0. 8 Enter or y to confirm that the keycode matches the system software on the RMD (see Figure 35 on page 121).
PAGE 122
Page 122 of 466 Installing software on the CS 1000E 9 The Install Menu appears (see Figure 36 on page 122). Enter b to install the software, database, and CP-BOOTROM. Figure 36 Install Menu The following screen appears (see Figure 37 on page 122): 10 Enter or y to confirm that the call processor is set to side 0. Figure 37 Side information NN43041-310 Standard 01.
PAGE 123
Installing software on the CS 1000E Page 123 of 466 11 The location information screen appears (see Figure 38), indicating that the call processor is located in loop 0 and shelf 0 of the IPMG. Enter or y to confirm their location. Figure 38 Call processor location 12 If not already present in the CF drive, insert the CF card containing CS 1000 Release 5.0 (see Figure 39). Figure 39 Insert RMD 13 Enter or y to confirm that you have the correct software version (see Figure 40 on page 124).
PAGE 124
Page 124 of 466 Installing software on the CS 1000E Figure 40 Confirm software version 14 Enter or y to install dependency lists and continue with the upgrade (see Figure 41 on page 124). Figure 41 Install Dependency Lists 15 Enter or y (the default) to enable the Automatic Centralized Software Upgrade (CSU) feature (see Figure 42 on page 125). NN43041-310 Standard 01.
PAGE 125
Installing software on the CS 1000E Page 125 of 466 Figure 42 Centralized Software Upgrade 16 Set the CSU feature to Sequential by entering either or y (see Figure 43). Figure 43 Automatic Centralized Software Upgrade Mode The Installation Status Summary screen appears (see Figure 44 on page 126).
PAGE 126
Page 126 of 466 Installing software on the CS 1000E Figure 44 Installation Status Summary 17 Enter or y to begin the installation (see Figure 45). Figure 45 Install Tool NN43041-310 Standard 01.
PAGE 127
Installing software on the CS 1000E Page 127 of 466 18 A prompt appears warning you that old system files will be deleted as a result of the installation. Enter or y to continue with the installation. 19 The PSDL Installation Menu appears (see Figure 46). Select the appropriate location based on your geographical location. Figure 46 The PSDL Installation Menu 20 Enter to continue. A message appears indicating that the installation on Core 0 was successful (see Figure 47).
PAGE 128
Page 128 of 466 Installing software on the CS 1000E Figure 48 Database installation 22 Enter a. 23 The Installation Status Summary screen appears, indicating that the installation was a success (see Figure 49). Enter to continue. NN43041-310 Standard 01.
PAGE 129
Installing software on the CS 1000E Page 129 of 466 Figure 49 Installation Status Summary 24 The Install Menu appears (see Figure 50 on page 130). Enter q to quit the Install Tool.
PAGE 130
Page 130 of 466 Installing software on the CS 1000E Figure 50 Install Menu 25 Enter or y to confirm your selection (see Figure 51). Figure 51 Quit Install Tool NN43041-310 Standard 01.
PAGE 131
Installing software on the CS 1000E Page 131 of 466 26 Enter or y to reboot the system (see Figure 52). Once the system has completed its reboot, remove the CF from the faceplate.
PAGE 132
Page 132 of 466 Installing software on the CS 1000E Reconfigure I/O ports and call registers Procedure 19 Reconfiguring I/O ports and call registers 1 2 Evaluate the number of call registers and 500 telephone buffers that are configured for the system (suggested minimum values are 4500 and 1000 respectively).
PAGE 133
Installing software on the CS 1000E Page 133 of 466 Test the CP PM Call Server Procedure 21 Testing the CP PM Call Server 1 Verify that the CP PM Call Server is active. LD 135 Load program STAT CPU Get the status of the CPUs 2 Check dial-tone. 3 Verify that the CP PM Call Server is active, redundant, and single. 4 Make internal, external, and network calls. 5 Check attendant console activity. 6 Check IP Peer networking for incoming and outgoing calls.
PAGE 134
Page 134 of 466 Installing software on the CS 1000E Verifying CP PM Call Server 0 is active Use the following commands to verify that CP PM Call Server 0 is active. LD 135 Load program STAT CPU Get the status of the CPUs CFN Make the system redundant At this point, Core/Net 0 is ready to be synchronized with Core/Net 1. Procedure 23 Making the system redundant 1 Check to see if the ELAN and TLAN cables are attached.
PAGE 135
Installing software on the CS 1000E Page 135 of 466 .stat cpu cp 0 16 PASS -- STDBY TRUE REDUNDANT DISK STATE = REDUNDANT HEALTH = 20 VERSION = Mar 3 2005, 16:26:40 Side = 0, DRAM SIZE = 512 MBytes cp 1 16 PASS -- ENBL TRUE REDUNDANT DISK STATE = REDUNDANT HEALTH = 20 VERSION = Mar 3 2005, 16:26:40 Side = 1, DRAM SIZE = 512 MBytes 3 Tier 1 and Tier 2 health of both CP PM Call Servers must be identical in order to successfully switch service from CP PM Call Server 1 to CP PM Call Server 0.
PAGE 136
Page 136 of 466 Installing software on the CS 1000E .stat health Local (Side 0, Active, Redundant): Components without TIER 1 Health contribution: ================================================= disp 0 15 1:In Service sio2 0 15 1:In Service cp 0 16:In Service ipb 0:In Service TIER 1 Health Count Breakdown: ===================================== sio8 0 16 1: 0002 sio8 0 16 2: 0002 sutl 0 15: 0002 strn 0 15: 0002 xsmp 0 15 1: 0002 eth 0 16 0: 0002 Local TIER 1 Health Total: 20 NN43041-310 Standard 01.
PAGE 137
Installing software on the CS 1000E Page 137 of 466 TIER 2 Health Count Breakdown: ======================================= ELAN 16 IP : 47.11.138.150 Health = 2 ELAN 17 IP : 47.11.138.
PAGE 138
Page 138 of 466 Installing software on the CS 1000E TIER 2 Health Count Breakdown: ======================================= ELAN 16 IP : 47.11.138.150 Health = 2 ELAN 17 IP : 47.11.138.153 Health = 2 Remote AML over ELAN Total Health:4 Remote Total IPL health = 6 Remote TIER 2 Health Total:10 4 Get status of links to the Media Gateways (STAT IPL).
PAGE 139
Installing software on the CS 1000E Page 139 of 466 Complete the CP PM installation Testing the CP PM Call Servers Procedure 24 Testing CP PM Call Server 0 At this point in the installation, CP PM Call Server 0 is tested from active CP PM Call Server 1. Upon successful completion of these tests, call processing is switched and the same tests are performed on CP PM Call Server 1 from active CP PM Call Server 0. As a final step, call processing is then switched again to CP PM Call Server 1.
PAGE 140
Page 140 of 466 Installing software on the CS 1000E 4 5 Test system redundancy and media devices: LD 137 Load program TEST RDUN Test redundancy DATA RDUN Test database integrity STAT FMD Status of one or both Fixed Media Devices (FMD) STAT RMD Status of one or both Removable Media Devices (RMD) Clear the display and minor alarms on both CP PM Call Servers: LD 135 Load program CDSP Clear the displays on the cores CMAJ Clear major alarms CMIN ALL Clear minor alarms 6 Check dial tone.
PAGE 141
Installing software on the CS 1000E Page 141 of 466 Procedure 26 Testing CP PM Call Server 1 From active CP PM Call Server 0, perform these tests on CP PM Call Server 1: 1 2 Perform a redundancy sanity test: LD 135 Load program STAT CPU Get status of CPU and memory TEST CPU Test the CPU Check the LCD states. a. Perform a visual check of the LCDs. b. Test LCDs: LD 135 Load program TEST LCDs Test LCDs DSPL ALL c. 3 4 Check that the LCD display matches the software check.
PAGE 142
Page 142 of 466 Installing software on the CS 1000E 5 STAT RMD Status of one or both Removable Media Devices (RMD) **** Exit the program Clear the display and minor alarms on both CP PM Call Servers: LD 135 Load program CDSP Clear the displays on the CP PM Call Servers CMAJ Clear major alarms CMIN ALL Clear minor alarms 6 Check dial tone. 7 Check applications (CallPilot, Symposium, etc.
PAGE 143
Installing software on the CS 1000E Page 143 of 466 Perform a customer backup data dump (installation release) Procedure 28 Performing a data dump to backup the customer database: 1 Log in to the system. 2 Insert a CF card into the active CP PM Call Server RMD slot to back up the database. 3 Load the Equipment Data Dump Program (LD 43). At the prompt, enter: 4 LD 43 Load program. . EDD When “EDD000” appears on the terminal, enter: EDD Begin the data dump.
PAGE 144
Page 144 of 466 Installing software on the CS 1000E The MGC must be given a superloop and shelf reference on the Call Server (see Table 13). Table 13 MGC superloop configuration Loop Shelf IPMG # 000 0 1 000 1 2 004 0 3 004 1 4 008 0 5 ... ... ... 096 0 49 096 1 50 Procedure 29 Configuring the MGC on the Call Server Note: Initial configuration of the MGC is command line ONLY. The MGC is shipped with “gold” software in onboard flash memory.
PAGE 145
Installing software on the CS 1000E Page 145 of 466 The MGC Shells can be accessed using the following commands: 1 • OAM, (provide OAM username and password to access OAM shell) • LDB, (provide LDB username and password to access LDB) Enter network IP information at the MGC setup menu: Please define the data networking parameters for this MG 1000E now. Hostname: MGC_N313 ELAN IP: 0.0.0.0 ELAN subnet mask: 0.0.0.0 ELAN gateway IP: 192.168.3.1 TLAN IP: 0.0.0.
PAGE 146
Page 146 of 466 Installing software on the CS 1000E 2 Enter port and security parameters, if required: Change MGC advanced parameters? (y/[n]) : y TLAN is set to auto negotiate, change? (y/[n]) : y Note: Turning off auto negotiate on the TLAN : will default it to 100Mbps full duplex. Set TLAN to auto negotiate? ([y]/n) : y ELAN is set to auto negotiate, change? (y/[n]) : y Note: Turning off auto negotiate on the ELAN : will default it to 100Mbps full duplex.
PAGE 147
Installing software on the CS 1000E Page 147 of 466 TLAN set to auto negotiate. ELAN set to auto negotiate. ELAN security Enabled, level is Optimized Security Is this correct? (y/n/[a]bort) : y 4 IP changes require a reboot. Enter “y” at the prompt. Do you want to continue? (y/n/[a]bort) : y reboot(-1) has been called... Following the reboot, the MGC connects to the CS and downloads the remaining configuration information.
PAGE 148
Page 148 of 466 Installing software on the CS 1000E 000 IPMG ---- -- - - -- - - 004 IPMG ---- -- - - -- - - 008 IPMG ---- -- - - -- - - 096 100 104 112 ------------- ------------- VIRTUAL VIRTUAL VIRTUAL VIRTUAL ----- - - 001 002 003 004 005 006 --------- ------------------------------------------------------------------------------- - --- ------------ - --- ------------ - --- ------------ - --- ---------- REQ chg TYPE supl SUPL 0 SLOT SUPT ipmg IPR0 IPR1
PAGE 149
Installing software on the CS 1000E Page 149 of 466 Rebooting the MGC The MGC reboots and registers with the Call Server. Found device : INTEL 82365SL Engcode:NTDW60BA REL 08 ELAN mac address is:00:13:65:ff:ee:ed TLAN mac address is:00:13:65:ff:ee:ec RESET reason: Hard Reset. Daughter board 1:NTDW62AA R02 00:13:65:ff:f8:fd. Daughter board 2:NOT INS VxWorks System Boot Copyright 1984-2005 Wind River Systems, Inc. CPU: Chagall Version: VxWorks5.5.1 Bootcode version: MGCBAA20 auto-booting...
PAGE 150
Page 150 of 466 Installing software on the CS 1000E -> Received an upgrade request. Preparing MGC for upgrade. Auto commit option has been enabled. Upgrade of CSP loadware initiated. OMM: IP link is UP between Primary Call Server and MGC 1 Upgrade Upgrade Upgrade Upgrade of of of of MSP loadware initiated. APP loadware initiated. FPGA loadware initiated. DBL1 initiated. -> 0x86f8bc30 (tMGCInst): Upgrading FPGA Loadware...
PAGE 151
172 Page 151 of 466 Configuring the CS 1000E CP PM Call Server Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Configuring login IDs and passwords. . . . . . . . . . . . . . . . . . . . . . . . . . 153 Enabling the multi-user option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Configuring pseudo-terminals (PTYs) . . . . . . . . . . . . . . . . . . . .
PAGE 152
Page 152 of 466 Configuring the CS 1000E CP PM Call Server Introduction The CS 1000E system requires the configuration of an IP telephony node. The configuration data is stored in the BOOTP.TAB and CONFIG.INI files on the CS 1000E. Copies of both files are maintained on each node component (Signaling Server and Media Card). The preconfigured IP telephony configuration files from the leader Signaling Server must be imported. These files are saved on the CS 1000E as: • c:/u/db/node/nodex.
PAGE 153
Configuring the CS 1000E CP PM Call Server Page 153 of 466 Configuring login IDs and passwords Note: You must be logged in as a user with admin2 level privileges in order to change the default username and password. For increased security: • Change the default login username and password. The default login is username admin1 and password 0000, as used throughout this guide. • Configure the Limited Access Password (LAPW) IDs and passwords. Follow Procedure 30 to configure login IDs and passwords.
PAGE 154
Page 154 of 466 Configuring the CS 1000E CP PM Call Server LOCK FLTA AUDT LLID 4 Enter the command: ACCOUNT_REQ new 5 Enter the command: PWD_TYPE pwd2 (pwd1, pwd2, lapw are options) 6 Enter the command: USER_NAME kattest (username) 7 Enter the command: PASSWORD (userpassword) 8 Enter the c
PAGE 155
Configuring the CS 1000E CP PM Call Server Page 155 of 466 15 Enter the command: PASSWORD (userpassword) 16 Enter the command: CONFIRM (confirm password) 17 Enter the command: OVLA 10 11 18 Enter the command: OVLA all 19 Enter the command: OVLA 20 Enter the command: Cust 0 21 Enter the command: TEN 22 Enter the command: CUST 23 Enter the command: HOST 24 Enter the command: MAT 25 Enter the command: OPT 26 Enter the command: PDT PWD ACCOUNT SETTINGS SAVED End of Procedure Communication Server 1000E Insta
PAGE 156
Page 156 of 466 Configuring the CS 1000E CP PM Call Server Enabling the multi-user option Follow Procedure 31 to enable the multi-user option. Procedure 31 Enabling the multi-user option 1 Enter the command: LD 17 System response: CFN000 MEM AVAIL: (U/P): 1015918 USED U P: 138773 24956 TOT: 1179647 DISK RECS AVAIL: 486 TMDI D-CHANNELS AVAIL: 0 USED: 0 TOT: 0 DCH AVAIL: 80 USED: 0 TOT: 80 AML AVAIL: 15 USED: 1 TOT: 16 2 Enter the command: REQ chg 3 Enter the command: TYPE ovly ....
PAGE 157
Configuring the CS 1000E CP PM Call Server Page 157 of 466 Configuring pseudo-terminals (PTYs) CS 1000E provides two ports (COM1 and COM2) on the CPU. A Terminal Server is used to provide additional serial ports for specific applications, such as, CTY, MCT, PMS, and TRF. Each configured Terminal Server serial port automatically starts an rlogin session with a user ID to a dedicated pseudo (PTY) port in the CS 1000E system.
PAGE 158
Page 158 of 466 Configuring the CS 1000E CP PM Call Server System response: CFN000 MEM AVAIL:(U/P):1019254 USED U P:138012 22381 TOT:1179647 DISK RECS AVAIL: 491 TMDI D-CHANNELS AVAIL: 0 USED: 0 TOT: 0 DCH AVAIL: 80 USED: 0 TOT: 80 AML AVAIL: 15 USED: 1 TOT: 16 2 Enter the command: REQ CHG 3 Enter the command: TYPE CFN 4 Enter the command: ADAN NEW TTY Where: = an available TTY number (0-15) 5 Enter the command: TTY_TYPE PTY 6 Enter the command: PORT Where: = an available PTY port
PAGE 159
Configuring the CS 1000E CP PM Call Server Page 159 of 466 10 Enter the command: TTYLOG NO 11 Enter the command: BANR YES System response: MEM AVAIL: (U/P):1019130 USED U P: 138064 22453 TOT: 3555327 DISK RECS AVAIL: 491 TMDI D-CHANNELS AVAIL: 0 USED: 0 TOT: 0 DCH AVAIL: 80 USED: 0 TOT: 80 AML AVAIL: 15 USED: 1 TOT: 16 ADAN DATA SAVED 12 Enter the command: ADAN **** End of Procedure Checking PTY status Follow Procedure 33 to check the PTY status.
PAGE 160
Page 160 of 466 Configuring the CS 1000E CP PM Call Server TTY 13: DSBL DES: ether 2 TTY 14: DSBL DES: ether 3 3 Enter the command: **** 4 Perform an EDD to save your changes. End of Procedure Configuring Virtual Tone and Conference Circuits Virtual Tone and Conference Circuits must be defined for use by each MG 1000E. Use LD 17 to add MGTDS and MG Conference loops. The Virtual Tone and Conference Circuits in the same MG 1000E must occupy contiguous double loops.
PAGE 161
Configuring the CS 1000E CP PM Call Server Page 161 of 466 Configuring the MG 1000E Bandwidth Management Zones Follow Procedure 34 for configuring bandwidth management zones. Procedure 34 Configuring MG 1000E Bandwidth Management Zone 1 Enter LD 117 and press . 2 Enter NEW ZONE 0, to create a new zone with default parameters. Note: LD 117 also includes DIS and ENL commands to disable or enable a zone. When you create a zone, its default state is enabled.
PAGE 162
Page 162 of 466 Configuring the CS 1000E CP PM Call Server LD 117 – Bandwidth management zone commands Command Description NEW ZONE xxx p1 p2 p3 p4 p5 Create a new zone, where: xxx = zone number = (0) - 255.
PAGE 163
Configuring the CS 1000E CP PM Call Server Page 163 of 466 The type of any Bandwidth Management Zone for MG 1000E with conference resources configured must be shared. Distortion in Music is expected when G.729AB codec is used. Hence the Interzone and the Intrazone policies for an MG 1000E Bandwidth Management Zone should have Best Quality to give preference to G711 codec to minimize of occurrence of music distortion.
PAGE 164
Page 164 of 466 Configuring the CS 1000E CP PM Call Server Configuring Digitone Receivers Digitone Receivers must be configured in each MG 1000E if any analog terminals or trunks are equipped. The loop of the Digitone Receivers is the superloop of the MG 1000E. The first MG 1000E in the superloop is on shelf 0, and the second MG 1000E’s on shelf 1.
PAGE 165
Configuring the CS 1000E CP PM Call Server Page 165 of 466 Configuring Tone Detectors Tone Detectors, when required, are configured in a manner similar to that for Digitone Receivers. The SSC card in the MG 1000E provides four units of Multifrequency Senders and Receivers. These units are configured on card 15 of the MG 1000E. In addition Multifrequency Transmit Level codes (MFTL0 and MFTL1) must be configured in LD 97.
PAGE 166
Page 166 of 466 Configuring the CS 1000E CP PM Call Server Note: This procedure requires Service Pack 1 and Java Runtime environment. Procedure 35 Launching Element Manager 1 Open the web browser. 2 Enter the Signaling Server Node IP address in the Address Bar of the browser window, and press Enter on the keyboard. Note: The ELAN network interface IP address may be required, instead of the Node IP address, to access the Element Manager login web page in secure environments.
PAGE 167
Configuring the CS 1000E CP PM Call Server Page 167 of 466 Figure 53 The Element Manager login End of Procedure Communication Server 1000E Installation and Commissioning
PAGE 168
Page 168 of 466 Configuring the CS 1000E CP PM Call Server Importing preconfigured IP telephony files Follow Procedure 36 to import the preconfigured IP telephony files from the Signaling Server. Procedure 36 Importing an existing node Figure 54 displays the Element Manager System Information home page. Figure 54 Element Manager – System Information NN43041-310 Standard 01.
PAGE 169
Configuring the CS 1000E CP PM Call Server 1 Page 169 of 466 Select System > IP Network > Nodes: Servers, Media Cards from the navigator. The Node Configuration web page appears. No nodes are defined. 2 Import the Node files from the leader Signaling Server. a. Click Import Node Files on the Node Configuration web page. The Import Node Files screen in Figure 55 on page 169 appears. b. Enter the ELAN IP address of the leader Signaling Server in the input box.
PAGE 170
Page 170 of 466 Configuring the CS 1000E CP PM Call Server Reviewing and submitting IP telephony node configuration files To review and submit IP telephony node configuration files, please refer to IP Line: Description, Installation, and Operation (NN43100-500). Adding a Follower Signaling Server to an IP telephony node To add a follower signaling server to an IP telephony node, follow the procedure as given in Signaling Server: Installation and Commissioning (NN43001-312).
PAGE 171
Configuring the CS 1000E CP PM Call Server Page 171 of 466 Figure 56 Call Server Backup and Restore web page 2 Select Backup. The Call Server Backup web page appears (see Figure 57 on page 172).
PAGE 172
Page 172 of 466 Configuring the CS 1000E CP PM Call Server Figure 57 CS 1000E Backup 3 Select Backup from the Action drop-down list box. 4 Click Submit. The message displays indicating “Backup in progress. Please wait...” 5 Click OK in the EDD complete dialog box. The Backup function then displays information in a tabular form, indicating the actions that were performed. End of Procedure NN43041-310 Standard 01.
PAGE 173
238 Page 173 of 466 Installing a Signaling Server Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Readiness checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Installing the CP PM Signaling Server hardware . . . . . . . . . . . . . . . . . 177 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 174
Page 174 of 466 Installing a Signaling Server Introduction This chapter contains general instructions to install a Nortel CP PM server and detailed instructions to install a legacy Nortel ISP1100 server. This chapter contains no instructions to install an IBM X306m or HP DL320-G4 COTS 1U server. Please see the IBM xSeries 306m Types 8848 and 8491 User Guide or the HP ProLiant DL320 Generation 4 Server User Guide shipped with the COTS servers for detailed installation instructions.
PAGE 175
Installing a Signaling Server Page 175 of 466 rack mounting, as opposed to two-post rack mounting for the Nortel ISP1100 server. IMPORTANT! Instructions to install an IBM X306m or HP DL320-G4 COTS 1U server are not included in this chapter. Detailed installation instructions can be found in the IBM xSeries 306m Types 8848 and 8491 User Guide or the HP ProLiant DL320 Generation 4 Server User Guide shipped with the server.
PAGE 176
Page 176 of 466 Installing a Signaling Server Table 14 Readiness checklist (Part 1 of 2) Have you: Read all safety instructions in Communication Server 1000E: Installation and Commissioning (NN43041-310) or Communication Server 1000M and Meridian 1 Large System Installation and Configuration (NN43021-310), as appropriate for your CS 1000 system? Received all equipment and peripherals? For a Nortel ISP1100 (NTDU27AA), IBM X306m (NTDU99AAE5), and HP DL320-G4 (NTDU97AA) Signaling Servers: • installation acce
PAGE 177
Installing a Signaling Server Page 177 of 466 Table 14 Readiness checklist (Part 2 of 2) Have you: Made sure the area meets all environmental requirements? Checked for all power requirements? Checked for correct grounding facilities? Obtained the following: • screwdrivers • an ECOS 1023 POW-R-MATE or similar type of multimeter • appropriate cable terminating tools • a computer (maintenance terminal) to connect directly to the Signaling Server, with: — teletype terminal (ANSI-W emulation, serial port, 960
PAGE 178
Page 178 of 466 Installing a Signaling Server This section contains general instructions for installing the CP PM Signaling Server circuit cards in CS 1000E and CS 1000M systems. For more detailed installation instructions, refer to Circuit Card: Description and Installation (NN43001-311) and Signaling Server: Installation and Commissioning (NN43001-312). IMPORTANT! There are several switches on CP PM circuit cards. All switch settings must be factory defaults except for the switch labelled “S5”.
PAGE 179
Installing a Signaling Server Page 179 of 466 Connections Connection checklist WARNING Do not modify or use a supplied AC power cord if it is not the correct type required for the host region. IMPORTANT! Nortel CP PM servers are powered through the backplane of the Media Gateway, Universal Equipment Module or 11C cabinet into which they are installed and thus require no power cord. Before connecting a Signaling Server, ensure that you have the following materials on-hand.
PAGE 180
Page 180 of 466 Installing a Signaling Server CS 1000M system respectively. It also contains instructions for connecting a maintenance terminal to the Nortel CP PM Signaling Server. The NTDW61BAE5 model of the Nortel CP PM Signaling Server was designed for use in a CS 1000E system. As such, it is inserted into a slot of the Media Gateway (MG 1000E or MG 1000B).
PAGE 181
Installing a Signaling Server Page 181 of 466 Figure 58 Faceplates of the Nortel CP PM server Communication Server 1000E Installation and Commissioning
PAGE 182
Page 182 of 466 Installing a Signaling Server Procedure 38 Connecting a Nortel CP PM Signaling Server Note: Refer to Figure 58 when performing the following procedure. 1 NN43041-310 Establish a maintenance terminal connection at the back of the shelf of the IPMG. The com (SDI) port of the CP PM circuit card Signaling Server is routed through the backplane of the shelf to the 50 pin MDF connector on the back of the shelf.
PAGE 183
Installing a Signaling Server 5 Page 183 of 466 Set the COM port on the maintenance terminal as follows: • Terminal type: VT100 • Speed: 9 600 • Data bits: 8 • Parity: none • Stop bits: 1 • Flow control: none Note: The CP PM Signaling Server is shipped with the Admin Serial port set to 9600 Bit/s. Other available speeds are 19 200, 38 400, and 115 200 Bits. You can change the port speed using the maintenance terminal.
PAGE 184
Page 184 of 466 Installing a Signaling Server 2 — Insert the end of a longer RJ-45 CAT5 Ethernet cable (not supplied) into the ELAN network interface port (ELAN port) on the faceplate of the server — Insert the other end of the RJ-45 CAT5 Ethernet cable into an Ethernet port on the ELAN Ethernet switch Connect the Signaling Server to the TLAN subnet.
PAGE 185
Installing a Signaling Server Page 185 of 466 Procedure 40 Connecting a CP PM Signaling Server to the ELAN and TLAN subnets of a CS 1000M system 1 Insert the end of an RJ-45 CAT5 Ethernet cable (not supplied) into the ELAN network interface port (ELAN port) on the back of the CS 1000M UEM. (You installed this ELAN port at the back of the UEM when you installed the Signaling Server in the UEM.) 2 Insert the other end of the RJ-45 CAT5 Ethernet cable into an Ethernet port on the ELAN Ethernet switch.
PAGE 186
Page 186 of 466 Installing a Signaling Server Figure 59 IBM X306m Signaling Server (rear view) Note: Refer to Figure 59 when performing the following procedure. Procedure 41 Connecting an IBM X306m Signaling Server NN43041-310 1 Connect the Signaling Server to the TLAN subnet. Insert the RJ-45 CAT5 (or better) cable into Port 1 (TLAN network interface) on the back of the Signaling Server. Port 1 is the right-most of the two network interfaces. 2 Connect the Signaling Server to the ELAN subnet.
PAGE 187
Installing a Signaling Server 5 Page 187 of 466 Set the baud rate for the serial port on the Signaling Server to 9 600 b/ps. See Signaling Server: Installation and Commissioning (NN43001-312). Note: The IBM X306m Signaling Server ships with the serial port set to 9600 b/ps. 6 Configure the connected maintenance terminal. See Signaling Server: Installation and Commissioning (NN43001-312). 7 Press the Power switch.
PAGE 188
Page 188 of 466 Installing a Signaling Server Procedure 42 Connecting an HP DL320-G4 Signaling Server 1 Connect the Signaling Server to the TLAN subnet. Insert the RJ-45 CAT5 (or better) cable labeled with the number 5 into the port (TLAN network interface) on the back of the Signaling Server. 2 Connect the Signaling Server to the ELAN subnet. Insert the RJ-45 CAT5 (or better) cable labeled with the number 6 into the port (ELAN network interface) on the back of the Signaling Server.
PAGE 189
Installing a Signaling Server Page 189 of 466 Installing the Signaling Server software IMPORTANT! The Signaling Server is out-of-service during software upgrade. Introduction This section provides installation procedures for CS 1000 Release 5.0 Signaling Server software on an IBM X306m or HP DL320-G4 Signaling Server. IMPORTANT! CP PM, IBM X306m and HP DL320-G4 Signaling Servers do not support any Signaling Server software prior to CS 1000 Release 5.0. IMPORTANT! CS 1000 Release 5.
PAGE 190
Page 190 of 466 Installing a Signaling Server Installing the software To install software and enter basic system configuration parameters on an IBM X306m or HP DL320-G4 Signaling Server, complete Procedure 43. Procedure 43 Installing Signaling Server software Upon completion of Step 1, this procedure takes approximately 45 minutes to complete.
PAGE 191
Installing a Signaling Server Page 191 of 466 Figure 61 Nortel CP PM system BIOS configuration • The VxWorksTM banner screen appears (see Figure 62) followed by system messages indicating that the Signaling Server Software Installation Tool is being loaded from either the Signaling Server Software CD or CF Card.
PAGE 192
Page 192 of 466 Installing a Signaling Server Figure 62 VxWorks system banner When the Install Tool banner appears (Figure 63), press to perform system checks and begin software installation. NN43041-310 Standard 01.
PAGE 193
Installing a Signaling Server Page 193 of 466 Figure 63 Install Tool banner screen CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 194
Page 194 of 466 Installing a Signaling Server The system verifies the file systems. • If the hard drive of the Signaling Server is not partitioned, the file systems verification process fails. Upon failure, the menu in Figure 64 appears. Figure 64 File systems verification failure CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== The filesystems verification failed! (This is normal for a new system.
PAGE 195
Installing a Signaling Server Page 195 of 466 Figure 65 Date and time CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ==================================================================== You should ensure the system date and time are correct prior to installation, since all files copied or created during install will be time-stamped. You can press to accept the current values.
PAGE 196
Page 196 of 466 Installing a Signaling Server Figure 66 System Summary CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== -----------------------------------------SYSTEM INFORMATION -----------------------------------------+================================================================+ | Hostname: SS_Node276_Ldr S/W Ver: x.xx.
PAGE 197
Installing a Signaling Server Page 197 of 466 Figure 67 Install Tool Main Menu CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== M A I N M E N U The Install Tool will install Signaling Server software and related files. You will be prompted throughout the installation.
PAGE 198
Page 198 of 466 Installing a Signaling Server The Dependency Lists installation screen appears (Figure 68). Figure 68 Dependency lists installation 5 Press or enter y to install the dependency lists. The Installation Status Summary screen appears: The Installation status screen appears (Figure 69 on page 199). NN43041-310 Standard 01.
PAGE 199
Installing a Signaling Server Page 199 of 466 Figure 69 Installation Status 6 Enter y to start the installation. The screens shown in Figures 70 to 76, which start on page 200, appear.
PAGE 200
Page 200 of 466 Installing a Signaling Server Figure 70 Installation output CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== You have selected to install version x.xx.xx on the system. As this is a new install, all necessary directories and files will be created on the hard disk. Starting new install of version x.xx.xx. Initializing protected partition ... “/p” initialized. Creating directory ...
PAGE 201
Installing a Signaling Server Page 201 of 466 Figure 72 IP Phone firmware CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== The installation source contains multiple Internet Telephone firmware files. Copying /cd0/0603Bxx.bin” to “/u/fw/0603Bxx.bin”. Copying “/cd0/0602Bxx.bin” to “/u/fw/0602Bxx.bin”. Copying “/cd0/0604Dxx.bin” to “/u/fw/0604Dxx.bin”.
PAGE 202
Page 202 of 466 Installing a Signaling Server Figure 74 Restore IP configuration 8 Do one of the following: • If you are migrating a Leader Signaling Server (see "Signaling Server migration" in Signaling Server: Installation and Commissioning (NN43001-312),insert the Removable Media Device (RMD) into the appropriate drive, and press or enter a to restore the IP configuration data.
PAGE 203
Installing a Signaling Server Page 203 of 466 Figure 75 IP telephony parameter confirmation 9 If you are installing a new Signaling Server, or you are migrating a Follower or Standalone Signaling Server (see "Signaling Server migration" in Signaling Server: Installation and Commissioning (NN43001-312)), select b to bypass the restoration of IP configuration data. The Signaling Server role selection screen appears (Figure 76 on page 204).
PAGE 204
Page 204 of 466 Installing a Signaling Server Figure 76 Signaling Server role selection CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Note: This step will over-write all existing configuration parameters on this Signaling Server. Please select the role of this Signaling Server. If this Signaling Server will be a Leader then its data networking and IP Telephony parameters must be entered now.
PAGE 205
Installing a Signaling Server Page 205 of 466 Figure 77 Follower Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ======================================================================= This Follower Signaling Server will obtain its data network and IP telephony configuration from the Leader Signaling Server at boot. To identify this Signaling Server, please enter a Hostname.
PAGE 206
Page 206 of 466 Installing a Signaling Server 11 Configure the application configuration for this Signaling Server. See Figure 78 on page 205. • If the IP Phone TPS, Virtual Trunk TPS, and optional Network Routing Service (NRS) applications are to be enabled on this Signaling Server, enter a at the prompt to configure this Signaling Server as a co-resident Signaling Server.
PAGE 207
Installing a Signaling Server Page 207 of 466 Figure 80 Network Routing Service (NRS) — stand-alone Signaling Server CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Please select the Network Routing Service (NRS) configuration for this Signaling Server. Please enter: -> - H.323 Gatekeeper and SIP Redirect/Proxy Server. - H.323 Gatekeeper only. - SIP Redirect/Proxy Server only.
PAGE 208
Page 208 of 466 Installing a Signaling Server Figure 81 NRS type — co-resident Signaling Server CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Please select the type of Network Routing Service (NRS) for this Signaling Server. Please enter: -> - Primary. - Alternate. - Failsafe. Enter Choice> Figure 82 NRS type — stand-alone Signaling Server CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 209
Installing a Signaling Server Page 209 of 466 Depending on whether the Signaling Server is configured as Leader or Standalone, either the Leader Signaling Server configuration screen (Figure 83) or the Standalone Signaling Server configuration screen (Figure 84) appears. Figure 83 Leader Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 210
Page 210 of 466 Installing a Signaling Server Figure 84 Stand-alone Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Please define the data networking parameters for this Standalone Signaling Server. Note that the ELAN parameters are necessary for management access (e.g. SNMP). Hostname : SS_SA ELAN IP : 192.168.10.20 ELAN subnet mask: 255.255.255.0 ELAN gateway IP : 192.168.10.
PAGE 211
Installing a Signaling Server Page 211 of 466 TLAN subnet parameters as required. The Call Server IP address is automatically set to 0.0.0.0. Depending on whether the Signaling Server is configured as Primary, Alternate, or Standalone, either the Primary NRS IP address screen, the Alternate NRS IP address screen, or both (in succession) appear. Both screens appear in succession for a Standalone Signaling Server. Figure 85 Primary NRS IP address CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 212
Page 212 of 466 Installing a Signaling Server — Enter the address of the Primary NRS (optional). — If you did enter the address of the Primary NRS, enter the address of the Alternate NRS (also optional). The Gatekeeper configuration can be updated later using Element Manager. The IP Telephony parameter confirmation screen appears (Figure 87). Figure 87 IP Telephony parameter configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 213
Installing a Signaling Server Page 213 of 466 16 Enter or y to confirm the parameters. The example in Figure 87 on page 212 is for a Leader Signaling Server configured with an Alternate H.323 and SIP NRS. The confirmation screens for a Follower and stand-alone Signaling Server are similar, showing the same list of parameters, specifically: • The configuration screen for the Follower Signaling Server displays only the value for the Hostname parameter; all other values are blank.
PAGE 214
Page 214 of 466 Installing a Signaling Server Figure 88 Installation Status Summary 18 Press to exit to the Main Menu (see Figure 89 on page 215). Enter q at the Main Menu to quit the installation process. Figure 90 on page 215 appears. Enter q again. NN43041-310 Standard 01.
PAGE 215
Installing a Signaling Server Page 215 of 466 Figure 89 Install Tool Main Menu CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== M A I N M E N U The Install Tool will install Signaling Server software and related files. You will be prompted throughout the installation.
PAGE 216
Page 216 of 466 Installing a Signaling Server 19 Remove the Signaling Server Software CD or the Signaling Server Software CF Card (as appropriate) from the RMD drive of the Signaling Server and enter q to close/terminate the Installation Tool and reboot the system. The following system messages appear: Removing temporary file "/u/disk.sys". Rebooting system .... End of Procedure First boot of a new Nortel CP PM Signaling Server Nortel CP PM Signaling Servers have CS 1000 Release 5.
PAGE 217
Installing a Signaling Server Page 217 of 466 – Primary and Alternate NRS IP addresses for this networked system. Refer to IP Peer Networking: Installation and Commissioning (NN43001-313) – NRS role, if applicable. Refer to IP Peer Networking: Installation and Commissioning (NN43001-313) Entering basic system parameters Procedure 44 Entering basic system configuration parameters 1 Press the RST button on the faceplate of the CP PM Signaling Server.
PAGE 218
Page 218 of 466 Installing a Signaling Server 2 Press to continue with the configuration. The Restore IP configuration screen appears (Figure 92). Figure 92 Restore IP configuration 3 Enter b at the prompt to bypass the restore of IP configuration data. The CP PM board location screen appears (Figure 93). Figure 93 CP PM board location NN43041-310 Standard 01.
PAGE 219
Installing a Signaling Server 4 Page 219 of 466 Enter the location (loop and shelf) of the IPMG board. Note: If the IPMG has not been configured yet, the loop and shelf information can be left at the current value. The IPMG board location can be updated using OAM shell commands after the Signaling Server is configured. 5 The Leader/Follower configuration screen appears (Figure 94). Figure 94 Leader/Follower Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 220
Page 220 of 466 Installing a Signaling Server Figure 95 Follower Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ======================================================================= This Follower Signaling Server will obtain its data network and IP telephony configuration from the Leader Signaling Server at boot. To identify this Signaling Server, please enter a Hostname.
PAGE 221
Installing a Signaling Server 8 Page 221 of 466 Configure the application configuration for this Signaling Server. See Figure 96. • If you are planning on enabling the IP Phone TPS, Virtual Trunk TPS, and optional Network Routing Service (NRS) applications on this Signaling Server, enter a at the prompt to configure this Signaling Server as a co-resident Signaling Server.
PAGE 222
Page 222 of 466 Installing a Signaling Server Figure 97 Standalone Signaling Server - NRS CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Please select the Network Routing Service (NRS) configuration for this Signaling Server. Please enter: -> - H.323 Gatekeeper and SIP Redirect/Proxy Server. - H.323 Gatekeeper only. - SIP Redirect/Proxy Server only.
PAGE 223
Installing a Signaling Server Page 223 of 466 Depending on whether the Signaling Server is configured as Leader, Follower or Stand-alone, the Leader Signaling Server configuration screen (Figure 99), the Follower Signaling Server configuration screen (Figure 100) or the Stand-alone Signaling Server configuration screen (Figure 101) appears. Figure 99 Leader Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 224
Page 224 of 466 Installing a Signaling Server Figure 101 Stand-alone Signaling Server configuration CS 1000 Signaling Server Software Install Tool (sse-x.xx.xx) ===================================================================== Please define the data networking parameters for this Standalone Signaling Server. Note that the ELAN parameters are necessary for management access (e.g. SNMP). Hostname : SS_SA ELAN IP : 192.168.10.20 ELAN subnet mask: 255.255.255.0 ELAN gateway IP : 192.168.10.
PAGE 225
Installing a Signaling Server Page 225 of 466 Figure 102 IP Telephony parameter configuration • Proceed to step 16 on page 213. • If this is a stand-alone Signaling Server and not associated with a Call Server (that is, b was selected in step 11 on page 206), enter the TLAN subnet parameters as required. The Call Server IP address is automatically set to 0.0.0.0. The IP information applies to a temporary IP Telephony node. This ensures that the existing node is not impacted.
PAGE 226
Page 226 of 466 Installing a Signaling Server Depending on whether the Signaling Server is configured as Primary, Alternate or Stand-alone, the Primary NRS IP address screen (Figure 103), the Alternate NRS IP address screen (Figure 104), or both in succession (for a Stand-alone Signaling Server) appear. Figure 103 Primary NRS IP address CS 1000 Signaling Server Software Install Tool (sse-x.xx.
PAGE 227
Installing a Signaling Server — Page 227 of 466 If you did enter the address of the Primary NRS, enter the address of the Alternate NRS (also optional). The Gatekeeper configuration can be updated later using Element Manager. The IP telephony parameter configuration screen appears (Figure 105).
PAGE 228
Page 228 of 466 Installing a Signaling Server 12 Press or enter y to confirm all parameters entered, n to re-enter all parameters, or a letter a through l to change the value of the corresponding system parameter. The configuration screens for a Follower and Standalone Signaling Server - NRS are similar, showing the same list of parameters, specifically: • The screen for the Follower Signaling Server displays only the value for the Hostname parameter; all other values are blank.
PAGE 229
Installing a Signaling Server Page 229 of 466 Figure 106 Install tool 13 Enter q to quit the Install Tool. Confirm to reboot the system. The Installation Tool quit confirmation screen appears (Figure 107).
PAGE 230
Page 230 of 466 Installing a Signaling Server Figure 107 Installation Tool quit confirmation 14 Enter q to close/terminate the Installation Tool and reboot the Signaling Server. End of Procedure Adding a follower Signaling Server After configuration and reboot, a Follower Signaling Server sends out BOOTP requests and waits for a response. Since the Follower Signaling Server is not yet configured in an IP Telephony node, there is no BOOTP response. Do not wait for this response.
PAGE 231
Installing a Signaling Server Page 231 of 466 Procedure 45 Adding a Follower Signaling Server to an IP Telephony node Note: The first time the Follower Signaling Server is installed, it cannot obtain the system login and password, and does not have the current CONFIG.INI file with the Call Server IP address, therefore the FTP fails. In subsequent Follower installations, FTP succeeds. 1 Open the Web browser.
PAGE 232
Page 232 of 466 Installing a Signaling Server Figure 108 Node Configuration web page 5 NN43041-310 Click Edit next to the node to which the Follower Signaling Server is to be added. The Edit web page opens, as shown in Figure 109. Standard 01.
PAGE 233
Installing a Signaling Server Page 233 of 466 Figure 109 Edit web page 6 Click Add next to Signaling Servers.The section expands to show a list of Signaling Servers and a blank template for entering Signaling Server xxx.xxx.xxx.xxx properties, as shown in Figure 110.
PAGE 234
Page 234 of 466 Installing a Signaling Server Figure 110 Signaling Server properties template 7 NN43041-310 Enter the information corresponding to the Follower Signaling Server. The Role field will automatically revert to Follower once the Follower Signaling Server has been added. Standard 01.
PAGE 235
Installing a Signaling Server 8 Page 235 of 466 Click Save and Transfer to transfer the updated IP Telephony node information to the other elements of the node. Refer to Transferring IP Telephony files, and IP Line: Description, Installation, and Operation (NN43001-500) for detailed instructions on transferring IP Telephony node information.
PAGE 236
Page 236 of 466 Installing a Signaling Server Procedure 46 Logging in to the Signaling Server Before you begin, make sure the DTE–DTE null modem cable (supplied with the Signaling Server) runs between the serial port on the back of the Signaling Server and the maintenance terminal. 1 Make sure the Signaling Server is powered up and connected to the maintenance terminal. Refer to Signaling Server: Installation and Commissioning (NN43001-312).
PAGE 237
Installing a Signaling Server Page 237 of 466 Verifying a successful configuration To ensure that the Signaling Server Ethernet connections (for the ELAN and TLAN subnets) are configured correctly, perform a ping test to one or more of the other devices connected to the network, particularly the Call Server. Procedure 47 Verifying the Signaling Server Ethernet connection 1 Log in to the Signaling Server, using Procedure 46 on page 236. 2 Ping the IP address of the Signaling Server.
PAGE 238
Page 238 of 466 NN43041-310 Installing a Signaling Server Standard 01.
PAGE 239
250 Page 239 of 466 Configuring the IPMG Contents This section contains information on the following topics: Configuring the IPMG in Element Manager. . . . . . . . . . . . . . . . . . . . . 239 Configuring conference TDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Configuring DSP Daughterboard Voice gateway channels . . . . . . . . .
PAGE 240
Page 240 of 466 Configuring the IPMG Procedure 48 Configuring the IPMG (Element Manager) 1 In Element Manager, select IP Network > Media Gateways. Select the appropriate Superloop Number and Shelf. Click Add. 2 The preceding screen appears (see Figure 111). Enter the IP address, zone number, and the Media Gateway type (in this case, a Media Gateway Controller). Selecting “MGC” automatically fills in the remaining fields (“CE”, “E1”, “E”, “CT”, “T2”, and “T”). Click Submit.
PAGE 241
Configuring the IPMG Page 241 of 466 Figure 112 IPMG MGC configuration 4 Once configuration of the MGC is complete, click Add. The following screen appears (see Figure 113 on page 242): 5 The Media Gateways screen lists the superloop and shelf numbers, IP address, zone, and type of the recently configured MGC. Click the radio-button next to the superloop. From the drop-down list select Add VGW channels.
PAGE 242
Page 242 of 466 Configuring the IPMG Figure 113 Media Gateways The following screen appears (see Figure 114): 6 In this screen, select the number of required channels, the Terminal Number (the superloop and shelf numbers of the MGC, the card number, and the unit). Provide a name and the daughterboard and customer type. Click Save. Figure 114 Add VGW channels NN43041-310 Standard 01.
PAGE 243
Configuring the IPMG Page 243 of 466 The following screen appears (Figure 115): The MGC has been added to the list. Figure 115 VGW Channels - IPMG End of Procedure Configuring conference TDS Procedure 49 on page 244 describes how to configure conference TDS for an IPMG using the CLI. To configure conference TDS for IPMG using Element Manager see Procedure 50 on page 245.
PAGE 244
Page 244 of 466 Configuring the IPMG Procedure 49 Configure conference TDS (CLI) 1 Enter LD 17.
PAGE 245
Configuring the IPMG Page 245 of 466 Procedure 50 describes how to configure conference TDS for IPMG using Element Manager. Procedure 50 Configuring conference TDS (Element Manager) 1 In the Element Manager screen, select IP Network > Nodes: Media Gateways. The Media Gateway Configuration page appears. 2 Select the IPMG superloop (see Figure 116). Click the Loops button. Figure 116 Media Gateway configuration The loop configuration page appears.
PAGE 246
Page 246 of 466 Configuring the IPMG Figure 117 Loop configuration The TDS loop configuration page appears (see Figure 118). 4 Enter the TDS loop number (0 – 255). Figure 118 TDS Loop configuration NN43041-310 Standard 01.
PAGE 247
Configuring the IPMG 5 Page 247 of 466 Click Save. It does not become available until a loop number has been entered and TAB has been used to move the cursor. The following message box appears: Figure 119 Confirmation 6 Click OK to complete the configuration. The updated loop configuration page appears (see Figure 120). The new Conference loop is displayed.
PAGE 248
Page 248 of 466 Configuring the IPMG Configuring DSP Daughterboard Voice gateway channels Procedure 51 describes how to configure DSP Daughterboard Voice gateway channels using the CLI. To configure DSP Daughterboard Voice gateway channels using Element Manager see Procedure 50 on page 245.
PAGE 249
Configuring the IPMG Page 249 of 466 ZONE 004 ...
PAGE 250
Page 250 of 466 NN43041-310 Configuring the IPMG Standard 01.
PAGE 251
264 Page 251 of 466 Connecting an IR-8020M-101 Terminal Server Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Configuring a Terminal Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Telnet Terminal Server virtual management port . . . . . . . . . . . . . . . . . 256 Telnet CS 1000E COM port from a PC . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 252
Page 252 of 466 Connecting an IR-8020M-101 Terminal Server information on connecting the MRV LX8020S-102AC-R, see “Connecting an MRV LX8020S-102AC-R Terminal Server” on page 265. As the Terminal Server is configured to automatically log in to the active Call Server upon start-up, only one Terminal Server is required for the system. It can be located anywhere on the LAN. One connection from each Call Server COM1 port is connected to the Terminal Server.
PAGE 253
Connecting an IR-8020M-101 Terminal Server Page 253 of 466 This chapter contains the following procedures: • Procedure 52: "Connecting a Terminal Server to the system" on page 254 • Procedure 53: "Configure IP address for the Terminal Server" on page 255 • Procedure 54: "Run telnet from PC" on page 256 • Procedure 55: "Accessing a CS 1000E from a PC through telnet Terminal Server" on page 257 • Procedure 56: "Configuring a transparent rlogin port" on page 258 • Procedure 58: "Accessing an MRV C
PAGE 254
Page 254 of 466 Connecting an IR-8020M-101 Terminal Server Customer-made cables with the following pin out (as NTDU6302) can also be used. See Table 17.
PAGE 255
Connecting an IR-8020M-101 Terminal Server 4 5 Page 255 of 466 Configure HyperTerminal to communicate with the Terminal Server’s management port: a. Set baud rate to 9600. b. Set data bits to 8. c. Set parity to none. d. Set stop bit to 1. e. Set flow control to “None”. f. Set Terminal Emulation to VT100. g. Press until you receive a log-in prompt. Log in to the Terminal Server. Enter: ACCESS 6 Enter the user name. Enter: ADMIN 7 Set privileged mode.
PAGE 256
Page 256 of 466 Connecting an IR-8020M-101 Terminal Server 3 Configure the Terminal Server’s IP primary gateway address. Enter: define server ip primary gateway address [ip address] 4 Check Terminal Server configuration. Enter: list server ip Example commands: define server ip address 172.16.3.50 define server ip subnet mask 255.255.255.0 define server ip primary gateway address 172.16.3.
PAGE 257
Connecting an IR-8020M-101 Terminal Server Page 257 of 466 Telnet CS 1000E COM port from a PC Connect port xx (xx = 1 - 19) of the Terminal Server to COM1 port of the CS 1000E Call Server. Follow Procedure 55 to establish access to a Call Server from a PC through telnet Terminal Server. Use the same port number for each procedure step.
PAGE 258
Page 258 of 466 Connecting an IR-8020M-101 Terminal Server b. Enter the Input telnet command. Enter the command: TELNET xxx.xx.x.xx xxxx Where: xxx.xx.x.xx = Terminal Server IP Address xxxx = telnet port (for port 1 to 19) Note: The value of the target telnet port, xxxx, is determined using the following formula: TELNET PORT = 2 000 + (port number × 100) For example, if the telnet port is 7, then: TELNET PORT = 2 000 + (port number x 100) = 2 000 + (700) = = 2700 If the Terminal Server IP Address is 172.
PAGE 259
Connecting an IR-8020M-101 Terminal Server Page 259 of 466 Where: xx = port number 2 Enable a dedicated service using rlogin. Enter the command: DEFINE PORT XX RLOGIN DEDICATED SERVICE xx.xx.xx.xx Where: xx = port number xx.xx.xx.xx = port IP address 3 Enable the port to be accessible only by local command and from a serial connection only.
PAGE 260
Page 260 of 466 Connecting an IR-8020M-101 Terminal Server 5 Enable autoconnect for the port. Enter the command: DEFINE PORT xx AUTOCONNECT ENABLED Where: xx = port number 6 Enable autodedicate for the port. Enter the command: DEFINE PORT xx AUTODEDICATED ENABLED Where: xx = port number 7 Define a user name for the port. Enter the command: DEFINE PORT xx USERNAME “ptyxx” Where: xx = port number ptyxx = User Name is the pty port set during Call Server configuration for rlogin connection.
PAGE 261
Connecting an IR-8020M-101 Terminal Server 9 Page 261 of 466 Check port configuration. Enter the command: LIST PORT xx LIST PORT xx ALTERNATE CHARA Where: xx = port number End of Procedure Configuring a transparent rlogin port with sample data Sample data has been incorporated into Procedure 57. This configuration shows that a device connected to MRV Port 2 will rlogin 47.11.166.76 through pty 10. Procedure 57 Configuring a transparent rlogin port 1 Enable keepalive timer 1 for the port.
PAGE 262
Page 262 of 466 Connecting an IR-8020M-101 Terminal Server 7 Define a user name for the port. Enter the command: DEFINE PORT 2 USERNAME “pty7” Note: When typing the letters “pty”, they must be lower case letters. The number must equal the pty number configured on the system. 8 Log out of the port. Enter the command: LOGOUT PORT 2 End of Procedure Accessing an MRV Console Port through the on-board modem The MRV IR-8020M Terminal Server is equipped with a V.90/K56flex 56 Kbps on-board modem.
PAGE 263
Connecting an IR-8020M-101 Terminal Server Page 263 of 466 CS 1000E COM port types Table 19 lists various components of the CS 1000E system and their COM port types. Table 19 System components and COM port type System component COM port type Baystack 460 9-pin DCE (male) Baystack 470 9-pin DCE (male) NTDU27 Signaling Server 9-pin DTE (male) Note: Signaling Server comes with a six-foot female-to-female null modem cable.
PAGE 264
Page 264 of 466 NN43041-310 Connecting an IR-8020M-101 Terminal Server Standard 01.
PAGE 265
278 Page 265 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 Configuring a Terminal Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Telnet Terminal Server virtual management port . . . . . . . . . . . . . . . . . 271 Telnet to CS 1000E COM port from a PC . . . . . . . . . . . . . . . . . . .
PAGE 266
Page 266 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server For information on connecting the IR-8020M-101, see “Connecting an IR-8020M-101 Terminal Server” on page 251. Differences between the two Terminal Servers include: • The IR-8020M-101 Management port is port 20. The LX8020S-102AC-R contains a Diag Port at the front. • The IR-8020M-101 contains an external PC card slot; the LX8020S-102AC-R does not.
PAGE 267
Connecting an MRV LX8020S-102AC-R Terminal Server Page 267 of 466 mask address and gateway address. The 20 Ports at the rear can be configured for Serial Data Interface for CS 1000E system components. IMPORTANT! Before connecting the Terminal Server to another component of the CS 1000E system, read and understand the documentation provided by the Terminal Server’s manufacturer including the Quick Start Guide for MRV server, LX Series Configuration Guide and MRV LX Series Commands Reference Guide.
PAGE 268
Page 268 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server Configuring a Terminal Server Follow Procedure 59 to connect a Terminal Server with a CS 1000E system. Table 20 lists the MRV cables required to install the LX8020S-102AC-R Terminal Server in a CS 1000E system.
PAGE 269
Connecting an MRV LX8020S-102AC-R Terminal Server Page 269 of 466 Table 21 Customer made cable pin out (same as NTDU6302) Pins on DB9 Female Pins on RJ-45 Male (MRV Terminal Server) 8 CTS 9 N/C 8 RTS Procedure 59 Connecting a Terminal Server to the system 1 Connect the above mentioned MRV serial cable from the Terminal Server Diag port at the front of the Terminal Server to the PC COM port. 2 Start the MRV HyperTerminal application.
PAGE 270
Page 270 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server System End of Procedure Configuring the Terminal Server IP address Procedure 60 Configure IP address for the Terminal Server Note: The IP address can be configured or changed only from the local Management/ DIAG port.
PAGE 271
Connecting an MRV LX8020S-102AC-R Terminal Server Page 271 of 466 Telnet Terminal Server virtual management port Connect the Terminal Server ethernet port to the ELAN subnet using a CAT5 ethernet cable. The virtual management port 0 is accessible from an online PC using a telnet session. The Terminal Server can now be configured from the on-line PC.
PAGE 272
Page 272 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server Follow Procedure 62 to establish access to a Call Server from a PC through telnet Terminal Server. Use the same port number for each procedure step. Procedure 62 Accessing a CS 1000E from a PC through telnet Terminal Server 1 Connect to the management port or virtual management port as shown in Procedure 61 on page 271 or Procedure 59 on page 269. 2 Define the port baud rate to equal the baud rate of the CS 1000E COM port.
PAGE 273
Connecting an MRV LX8020S-102AC-R Terminal Server Page 273 of 466 xxx.xx.x.xx = Terminal Server IP Address xxxx = telnet port (for port 1 to 20) Note: The value of the target telnet port, xxxx, is determined using the following formula: TELNET PORT = 2 000 + (port number xx × 100) For example, if the telnet port is 1, then: TELNET PORT = 2 000 + (1 x 100) = 2 000 + (100) = = 2100 If the Terminal Server IP Address is 47.11.244.101 and the telnet port is 1, then TELNET command line is: telnet 47.11.244.
PAGE 274
Page 274 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server a. Connect to the management port or virtual management port b. At the InReach: 0>> prompt, type shell. The shell window opens. InReach: 0 >>shell BusyBox v1.1.3 (2006.10.20-12:27+0000) Built-in shell (ash) c. It will then go to the LX prompt as shown below. Type the below command to start editing. LX:/config# vi sysctl.conf. d. Once the VI editor starts, start by pressing the letter “i” to enter the insert mode.
PAGE 275
Connecting an MRV LX8020S-102AC-R Terminal Server Page 275 of 466 InReach:0>>configure rlogin enable. 4 Configure the rlogin port for various applications. InReach: 0>> config port async xx connect command rlogin -l user_name host_ip_address InReach: 0 >>config port async 1 connect command rlogin -l pty8 47.11.244.101 Here PTY8 is the user name.It is the port no. used while configuring the PTY.
PAGE 276
Page 276 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server Note 1: It is not advisable to use putty software while trying to do rlogin Note 2: MRV definition of autoconnect: In Procedure 62 on page 272 and Procedure 63 on page 273 this feature of autoconnect is required. This command is used to specify whether or not the port will automatically connect to either a dedicated service or a preferred service when the user logs onto a port.
PAGE 277
Connecting an MRV LX8020S-102AC-R Terminal Server Page 277 of 466 Login 5 Log in to the LX-series Element Manager using the default password, (see steps 4,5,6,and 7 in Procedure 59 on page 269). Once logged into the onboard modem, it is possible to telnet to ports 1-20.It is also possible to rlogin to different IPs. IMPORTANT! For this version of the LX series, always remember that the modem port is 21.And this port can be configured as telnet or rlogin port.
PAGE 278
Page 278 of 466 Connecting an MRV LX8020S-102AC-R Terminal Server Table 22 System components and COM port type (Part 2 of 2) System component COM port type P0609205 MIRAN L-adapter 9-pin DTE (male) NTDU14 Gateway 9-pin DTE (male) (modified to isolate pins 6, 7, and 8) Use PORT 0 of NTBK48AA 3-port SDI cable. NN43041-310 Standard 01.
PAGE 279
286 Page 279 of 466 Configuring a terminal and SDI ports Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Setting the TTY terminal port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Traditional terminal SDI connection. . . . . . . . . . . . . . . . . . . . . . . . . . . 280 CS 1000E CP PM Call Server COM Port connections. . . . . . . . . . . . .
PAGE 280
Page 280 of 466 Configuring a terminal and SDI ports Setting the TTY terminal port A TTY terminal can be any standard PC running terminal software, (for example, HyperTerminal). The TTY terminal port must be configured as: • Bits per second - Baud rate must be the same as the speed of SDI port. • Data bits - 8 • Parity- None • Stop bit – 1 • Flow control – None • Terminal Emulation- VT100 Traditional terminal SDI connection Figure 121 shows the setup values for a traditional terminal setup.
PAGE 281
Configuring a terminal and SDI ports Page 281 of 466 Figure 121 VT220 setup values Global Set-Up On Line Sessions on Comm1 CRT Saver Comm1=RS232 70Hz Printer Shared Display Set-Up 80 Columns Interpret Controls Auto Wrap Jump Scroll Light Text, Dark Screen Cursor Block Style Cursor General Set-up VT200 Mode, 7-bit Controls User Defined Keys Unlocked User Features Unlocked Multinational Application Keypad Normal Cursor Keys No New Line Communications Set-Up Transmit=2400 Receive=Transmit Xoff at 64 8b
PAGE 282
Page 282 of 466 Configuring a terminal and SDI ports • Parity - none • Flow control - none The baudrate setting can be changed in Overlay 17, however changing this setting is not recommended since it will only used when SL1 is loaded. Note that only the Port 0 serial port displays the boot sequence from BIOS, Bootrom & OS before the call server application is started. Port 1 will only start displaying output when call server application is started (Sysload Phase1).
PAGE 283
Configuring a terminal and SDI ports Page 283 of 466 SDI2 is not available during the MGC bootup, it cannot be used to access the installation menus. All of the SDI ports on the MGC are configured via software. There are no DIP switches on the MGC for configuring the baud rate of SDI0. Controlling the baud rate You can use a switch setting on the SSC’s faceplate to control the baud rate for port 0. Use LD 17 to configure port 1 and port 2.
PAGE 284
Page 284 of 466 Configuring a terminal and SDI ports Procedure 65 Connecting SDI ports on the Media Gateways 1 Connect the NTBK48 3-port SDI cable to the 9-pin SDI port (RS-232) at the rear of the Media Gateways (see Figure 122). Figure 122 SDI port access to the Media Gateway SSC card SDI port 2 Connect the system terminal to the cable marked “port 0” on the NTBK48 3-port cable. You require a Modem Eliminator adapter to connect the system to a TTY terminal.
PAGE 285
Configuring a terminal and SDI ports Page 285 of 466 BayStack 470 SDI connection The SDI port on the Bay Stack 470 can be used for basic configuration and maintenance. The SDI port is located on the faceplate. It is a DCE port with a default speed of 9600 bps. Media Card SDI connection The SDI ports on a Media Card can be used for basic configuration or maintenance. Figure 123 shows the maintenance port location on the Media Card and the Shielded 50-pin to Serial/ELAN/TLAN adapter.
PAGE 286
Page 286 of 466 Configuring a terminal and SDI ports to Serial/ELAN/TLAN adapter provides an alternative to the faceplate maintenance port. Both are DTE ports with a speed of 9600 bit/s. CAUTION — Service Interruption Do not connect maintenance terminals or modems to the faceplate and I/O panel DB-9 male serial maintenance port at the same time. NN43041-310 Standard 01.
PAGE 287
316 Page 287 of 466 Installing and cross-connecting a trunk card Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Circuit card options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Digital trunk cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Connecting a trunk . . . . . . . . . . . . . . . . .
PAGE 288
Page 288 of 466 Installing and cross-connecting a trunk card IMPORTANT! Digital Trunk cards can be installed only in slots 1 to 4 of the Media Gateway. Figure 124 shows the circuit card slots in a Media Gateway. To view the circuit card slots available in a Media Gateway Expander, see Figure 125 on page 289. Figure 124 Circuit card assignments in the Media Gateway SLOT 4 SLOT 3 SLOT 2 SLOT 1 SLOT 0 SSC Slot 4 Slot 3 Slot 2 Slot 1 Slot 0 - SSC 553-CSE9025 NN43041-310 Standard 01.
PAGE 289
Installing and cross-connecting a trunk card Page 289 of 466 Figure 125 Circuit card assignments in the Media Gateway Expander SLOT 10 SLOT 9 SLOT 8 SLOT 7 Slot 10 Slot 9 Slot 8 Slot 7 553-CSE9032 WARNING Use caution when installing or modifying telephone lines. Avoid installing telephone wiring during a lightning storm. Do not install telephone jacks in wet locations unless the jacks are designed for wet locations.
PAGE 290
Page 290 of 466 Installing and cross-connecting a trunk card Before you proceed, install the cable from the slot that contains the Line card associated with the telephone being connected. Refer to “Installing the Main Distribution Frame” on page 349, if you require additional cable installation. DANGER OF ELECTRIC SHOCK Always use caution when installing or modifying telephone lines. Do not install telephone wiring during a lightning storm.
PAGE 291
Installing and cross-connecting a trunk card Page 291 of 466 Figure 126 Antistatic wrist strap Antistatic wrist strap Circuit card options A circuit card that has a switch symbol on its faceplate is equipped with option switches, strapping plugs, or both. Ensure that the option switches or strapping plugs are set correctly. Circuit cards can also have daughterboards or other add-on devices installed on them.
PAGE 292
Page 292 of 466 Installing and cross-connecting a trunk card • NTRB21 TMDI 1.5 Mbit DTI/PRI • NT6D70 SILC • NT6D71 UILC Note: Now NT6D70 SILC and NT6D71 UILC Digital trunk cards can be installed in slots 7 to 10 in a Media Gateway Expander.
PAGE 293
Installing and cross-connecting a trunk card Page 293 of 466 Note: See “Installing and cross-connecting a Power Fail Transfer Unit” on page 437 for connecting trunks with the PFTU. End of Procedure Universal Trunk card connections The Universal Trunk card (NT8D14) provides eight Analog trunks that can function in the modes identified in Table 24. Refer to Table 25 on page 294 for the connections to the Universal trunk at the cross-connect terminal.
PAGE 294
Page 294 of 466 Installing and cross-connecting a trunk card Table 25 NT8D14 Universal Trunk connections (Part 1 of 2) Cable from equipment Pair Color 1T 1R W-BL BL-W 2T 2R Unit RAN mode Paging mode All other modes Designations T0 R0 T0 R0 W-O O-W CP MB A PG 3T 3R W-G G-W T1 R1 T1 R1 4T 4R W-BR BR-W CP MB A PG 5T 5R W-S S-W T2 R2 T2 R2 6T 6R R-BL BL-R CP MB A PG 7T 7R R-O O-R T3 R3 T3 R3 8T 8R R-G G-R CP MB A PG 9T 9R R-BR BR-R T4 R4 T4 R4 10T 10R R-S S-R CP MB
PAGE 295
Installing and cross-connecting a trunk card Page 295 of 466 Table 25 NT8D14 Universal Trunk connections (Part 2 of 2) Cable from equipment Pair Color 13T 13R BK-G G-BK 14T 14R Unit RAN mode Paging mode All other modes Designations T6 R6 T6 R6 BK-BR BR-BK CP MB A PG 15T 15R BK-S S-BK T7 R7 T7 R7 16T 16R Y-BL BL-Y CP MB A PG T6 R6 6 T7 R7 7 Note: Remaining pairs are spare.
PAGE 296
Page 296 of 466 Installing and cross-connecting a trunk card E&M Trunk card connections Table 26 lists the connections required by the E&M Trunk card (NT8D15).
PAGE 297
Installing and cross-connecting a trunk card Page 297 of 466 Table 26 NT8D15 E&M Trunk card (Part 2 of 2) Cables Card 1 through Card 10 from equipment Unit 2W Paging mode Pair Color 9T 9R R-BR BR-R 10T 10R R-S S-R 11T 11R BK-BL BL-BK 12T 12R BK-O O-BK A PG 13T 13R BK-G G-BK T3 R3 14T 14R BK-BR BR-BK 15T 15R BK-S S-BK 16T 16R Y-BL BL-Y 2W Type 1 mode 4W Type 1 mode 4W Type 2 mode Designations T2 R2 T2 R2 2 E M T3 R3 3 E M A PG TA TB TA TB RA RB RA RB E M EA EB ESC ESCG
PAGE 298
Page 298 of 466 Installing and cross-connecting a trunk card Trunk connections (Europe) Trunk connections for Europe are provided in the following tables: • Table 27: “E&M TIE trunk card (2-Wire)” on page 298 • Table 28: “E&M 2-wire Type 2” on page 299 • Table 29: “E&M TIE Trunk card (4-Wire)” on page 300 • Table 30: “E&M TIE Trunk card” on page 302 • Table 31: “E&M 2280 Hz TIE Trunk connections” on page 303 • Table 32: “E&M 2-wire Recorded Announcement Trunk connections” on page 304 • Table
PAGE 299
Installing and cross-connecting a trunk card Page 299 of 466 Table 27 E&M TIE trunk card (2-Wire) (Part 2 of 2) Column 1 Paging Column 2 Paging Column 3 Type 5 (BPO) 35 10 T2 R2 T2 R2 T2 R2 37 12 A PG SIGB SIGA E M 39 14 T3 R3 T3 R3 T3 R3 41 16 A PG SIGB SIGA E M Cables Card 1 through Card 10 from equipment 5T 5R R-S S-R 6T 6R BK-O O-BK 7T 7R BK-BR BR-BK 8T 8R Y-BL BL-Y 2 3 Table 28 E&M 2-wire Type 2 (Part 1 of 2) Lead designations Pins Pair color T0 R0 27 2 W-O O-W E1
PAGE 300
Page 300 of 466 Installing and cross-connecting a trunk card Table 28 E&M 2-wire Type 2 (Part 2 of 2) T2 R2 35 10 R-S S-R E1 E2 36 11 BK-BL BL-BK M1 M2 37 12 BK-O O-BK T3 R3 39 14 BK-BR BR-BK E1 E2 40 15 BK-S S-BK M1 M2 41 16 Y-BL BL-Y 2 3 Table 29 E&M TIE Trunk card (4-Wire) (Part 1 of 2) Cables Card 1 through Card 10 from equipment NN43041-310 Unit # Column 1 Type 1 & 5 Pair Color 1T 1R W-BL BL-W 26 1 RA RB TA TB 2T 2R W-O O-W 27 2 TA TB RA RB 3T 3R W-G G-W 28 3 E M
PAGE 301
Installing and cross-connecting a trunk card Page 301 of 466 Table 29 E&M TIE Trunk card (4-Wire) (Part 2 of 2) Cables Card 1 through Card 10 from equipment Column 1 Type 1 & 5 Column 2 Type 1 & 5 4T 4R W-S S-W 30 5 RA RB TA TB 5T 5R R-BL BL-R 31 6 TA TB RA RB 6T 6R R-O O-R 32 7 E M E M 7T 7R R-BR BR-R 34 9 RA RB TA TB 8T 8R R-S S-R 35 10 TA TB RA RB 9T 9R BK-BL BL-BK 36 11 E M E M 10T 10R BK-G G-BK 38 13 RA RB TA TB 11T 11R BK-BRBR-BK 39 14 TA TB RA RB 12T 12R
PAGE 302
Page 302 of 466 Installing and cross-connecting a trunk card Table 30 E&M TIE Trunk card (Part 1 of 2) Cables Card 1 through Card 10 from equipment NN43041-310 Unit # Column 1 Type 2 Pair Color 1T 1R W-BL BL-W 26 1 RA RB RA RB 2T 2R W-O O-W 27 2 TA TB TA TB 3T 3R W-G G-W 28 3 E1 E2 E M 4T 4R W-BR BR-W 29 4 M1 M2 SIG0A SIG0B 5T 5R W-S S-W 30 5 RA RB RA RB 6T 6R R-BL BL-R 31 6 TA TB TA TB 7T 7R R-O O-R 32 7 E1 E2 E M 8T 8R R-G G-R 33 8 M1 M2 SIG1A SIG1B 9T 9R R-
PAGE 303
Installing and cross-connecting a trunk card Page 303 of 466 Table 30 E&M TIE Trunk card (Part 2 of 2) Cables Card 1 through Card 10 from equipment 13T 13R BK-G G-BK Column 1 Type 2 Column 2 Type 2 38 13 RA RB RA RB 3 14T 14R BK-BR BR-BK 39 14 TA TB TA TB 15T 15R BK-S S-BK 40 15 E1 E2 E M 16T 16R Y-BL BL-Y 41 16 M1 M2 SIG3A SIG3B Note: The cable pair designated TA, TB is the transmit pair. The pair designated RA, RB is the receive pair.
PAGE 304
Page 304 of 466 Installing and cross-connecting a trunk card Table 31 E&M 2280 Hz TIE Trunk connections (Part 2 of 2) TA TB 34 9 R-BR BR-R RA RB 35 10 R-S S-R TA TB 38 13 BK-G G-BK RA RB 39 14 BK-BR BR-BK 2 3 Table 32 E&M 2-wire Recorded Announcement Trunk connections NN43041-310 Lead designations Pins Pair color T0 R0 26 1 W-BL BL-W SIG B SIG A 29 4 W-BR BR-W T1 R1 30 5 W-S S-W SIG B SIG A 33 8 R-G G-R T2 R2 34 9 R-BR BR-R SIG B SIG A 37 12 BK-O O-BK T3 R3 38 13 BK-G
PAGE 305
Installing and cross-connecting a trunk card Page 305 of 466 Table 33 E&M 2-wire Music Trunk connections Lead designations Pins Pair color Unit number T0 R0 26 1 W-BL BL-W 0 T1 R1 30 5 W-S S-W 1 T2 R2 34 9 R-BR BR-R 2 T3 R3 38 13 BK-G G-BK 3 Table 34 Central Office & Direct Dial Inward Trunk connections (Part 1 of 2) Cable from equipment Pair Color 1T 1R W-BL BL-W 2T 2R W-O O-W 3T 3R W-G G-W 4T 4R W-BR BR-W 5T 5R W-S S-W 6T 6R R-BL BL-R Column 1 Unit Pins 26 1 0 2 T0
PAGE 306
Page 306 of 466 Installing and cross-connecting a trunk card Table 34 Central Office & Direct Dial Inward Trunk connections (Part 2 of 2) Cable from equipment Pair Color 7T 7R R-O O-R 8T 8R R-G G-R 9T 9R R-BR BR-R 10T 10R R-S S-R 11T 11R BK-BL BL-BK 12T 12R BK-O O-BK 13T 13R BK-G G-BK 14T 14R BK-BR BR-BK 15T 15R BK-S S-BK 16T 16R Y-BL BL-Y NN43041-310 Column 1 Unit Pins 32 7 3 4 5 Standard 01.
PAGE 307
Installing and cross-connecting a trunk card Page 307 of 466 Table 35 Central Office Trunk connections (Part 1 of 2) Cable from equipment Pair Color 1T 1R Unit Pins Lead designations W-BL BL-W 26 1 T0 R0 2T 2R W-O O-W 27 2 3T 3R W-G G-W 28 3 4T 4R W-BR BR-W 29 4 5T 5R W-S S-W 30 5 6T 6R R-BL BL-R 31 6 7T 7R R-O O-R 32 7 8T 8R R-G G-R 33 8 9T 9R R-BR BR-R 34 9 10T 10R R-S S-R 35 10 11T 11R BK-BL BL-BK 36 11 12T 12R BK-O O-BK 37 12 0 1 2 Communication Server 1000
PAGE 308
Page 308 of 466 Installing and cross-connecting a trunk card Table 35 Central Office Trunk connections (Part 2 of 2) Cable from equipment Pair Color 13T 13R Unit Pins Lead designations BK-G G-BK 38 13 T3 R3 14T 14R BK-BR BR-BK 39 14 15T 15R BK-S S-BK 40 15 16T 16R Y-BL BL-Y 41 16 3 Trunk connections (UK) Trunk connections for the UK are provided in the following tables: NN43041-310 • Table 36: “NT5K17 Direct Inward Dial card terminations” on page 309 • Table 37: “NT5K18 Exchange lin
PAGE 309
Installing and cross-connecting a trunk card Page 309 of 466 Table 36 NT5K17 Direct Inward Dial card terminations (Part 1 of 2) Pair Pins Pair color Unit T0 R0 26 1 W-BL BL-W 0 27 2 W-O O-W 28 3 W-G G-W 29 4 W-BR BR-W 30 5 W-S S-W 31 6 R-BL BL-R 32 7 R-O O-R 33 8 R-G G-R 34 9 R-BR BR-R 35 10 R-S S-R 36 11 BK-BL BL-BK 37 12 BK-O O-BK 38 13 BK-G G-BK T1 R1 T2 R2 T3 R3 T4 R4 T5 R5 T6 R6 Communication Server 1000E 1 2 3 4 5 6 Installation and Commissioning
PAGE 310
Page 310 of 466 Installing and cross-connecting a trunk card Table 36 NT5K17 Direct Inward Dial card terminations (Part 2 of 2) Pair T7 R7 Pins Pair color 39 14 BK-BR BR-BK 40 15 BK-S S-BK 41 16 Y-BL BL-Y Unit 7 Note: The connections on the NT5K18 Exchange Line Trunk card are polarity-sensitive. Make sure the ground side of the trunk is connected to the A leg of the NT5K18 circuit. Make sure the -50 Volt side of the trunk is connected to the B leg of the NT5K18 circuit.
PAGE 311
Installing and cross-connecting a trunk card Page 311 of 466 Table 37 NT5K18 Exchange line trunk card cross-connect terminations (Part 2 of 2) Pair Pins Pair color Unit T3 R3 32 7 R-O O-R 3 33 8 R-G G-R 34 9 R-BR BR-R 35 10 R-S S-R 36 11 BK-BL BL-BK 37 12 BK-O O-BK 38 13 BK-G G-BK 39 14 BK-BR BR-BK 40 15 BK-S S-BK 41 16 Y-BL BL-Y T4 R4 T5 R5 T6 R6 T7 R7 Communication Server 1000E 4 5 6 7 Installation and Commissioning
PAGE 312
Page 312 of 466 Installing and cross-connecting a trunk card Note: The speech pairs on the NT5K19 card are polarity-insensitive. The E&M signaling pairs, however, are polarity-sensitive. Make sure the ground side of the trunk is connected to the A leg of the NT5K19 circuit. Make sure the -50 Volt side of the trunk is connected to the B leg.
PAGE 313
Installing and cross-connecting a trunk card Page 313 of 466 Table 39 NT5K19 2W Type 1 mode terminations (Part 2 of 2) Pair Pins Pair color Unit T1 R1 31 6 R-BL BL-R 1 E M 32 & R-O O-R T2 R2 35 10 R-S S-R E M 36 11 BK-BL BL-BK T3 R3 39 14 BK-BR BR-BK E M 40 15 BK-S S-BK Communication Server 1000E 2 3 Installation and Commissioning
PAGE 314
Page 314 of 466 Installing and cross-connecting a trunk card Table 40 NT5K19 4W Type 1 mode terminations NN43041-310 Pair Pins Pair color TA TB 26 1 W-BL BL-W RA RB 27 2 W-O O-W E M 28 3 W-G G-W RA RB 30 5 W-S S-W TA RB 31 6 R-BL BL-R E M 32 7 R-O O-R TA TB 34 9 R-BR BR-R RA RB 35 10 R-S S-R E M 36 11 BK-BL BL-BK TA TB 38 13 BK-G G-BK RA TB 39 14 BK-BR BR-BK E M 40 15 BK-S S-BK Standard 01.
PAGE 315
Installing and cross-connecting a trunk card Page 315 of 466 Table 41 NT5K19 AC15 mode pair terminations Pair Pins Pair color Unit TA TB 26 1 W-BL BL-W 0 RA RB 27 2 W-O O-W TA TB 30 5 W-S S-W RA RB 31 6 R-BL BL-R TA TB 34 9 R-BR BR-R RA RB 35 10 R-S S-R TA TB 38 13 BK-G G-BK RA TB 39 14 BK-BR BR-BK Communication Server 1000E 1 2 3 Installation and Commissioning
PAGE 316
Page 316 of 466 Installing and cross-connecting a trunk card Table 42 NT5K19 Recorded Announcement mode pair terminations Pair Pins Pair color Unit T0 R0 26 1 W-BL BL-W 0 SIG B SIG A 29 4 W-BR BR-W T1 R1 30 5 W-S S-W SIG B SIG A 33 8 R-G G-R T2 R2 34 9 R-BR BR-R SIG B SIG A 37 12 BK-O O-BK T3 R3 38 13 BK-G G-BK SIG B SIG A 41 16 Y-BL BL-Y 1 2 3 Verifying trunk functionality You can now use the trunks. To test the trunks, make trunk calls. NN43041-310 Standard 01.
PAGE 317
348 Page 317 of 466 Installing and configuring a Voice Gateway Media Card Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Configuring a card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Adding a card to an IP telephony node . . . . . . . . . . . . . . . . . . . . . . . . . 319 Configuring a card as a node Leader. . . . . . . . . . .
PAGE 318
Page 318 of 466 Installing and configuring a Voice Gateway Media Card Introduction The Voice Gateway Media Card provides access to the voice gateway and functions as a Follower to the Signaling Server, which is the node Leader and which, by default, acts as a Master for the node. In the absence of the Signaling Server a Voice Gateway Media Card may be an active Leader, a backup Leader, or a Follower. Each customer in a system has only one Leader. A Voice Gateway Media Card runs the IP Line 3.1 software.
PAGE 319
Installing and configuring a Voice Gateway Media Card Page 319 of 466 • Procedure 74: "Displaying the status of Voice Gateway Media Card units" on page 341 • Procedure 75: "Displaying the status of one unit on a Voice Gateway Media Card" on page 344 • Procedure 76: "Disabling a Voice Gateway Media Card using Element Manager" on page 344 • Procedure 77: "Disabling a Voice Gateway Media Card unit using Element Manager" on page 345 • Procedure 78: "Enabling a Voice Gateway Media Card using Element M
PAGE 320
Page 320 of 466 Installing and configuring a Voice Gateway Media Card Figure 127 Node Configuration web page 3 Click Edit next to the Node to which the Voice Gateway Media Card is to be added. The Edit web page opens, as shown in Figure 128 on page 321. NN43041-310 Standard 01.
PAGE 321
Installing and configuring a Voice Gateway Media Card Page 321 of 466 Figure 128 Edit web page 4 Click Add next to the Cards tab. The Cards tab expands (see Figure 129 on page 322). 5 Enter your data for this Voice Gateway Media Card. The ELAN MAC address is on a faceplate sticker. The TN is the Voice Gateway Media Card logical card slot. Note: For more detail on Voice Gateway Media Card properties, see IP Line: Description, Installation, and Operation (NN43100-500).
PAGE 322
Page 322 of 466 Installing and configuring a Voice Gateway Media Card Figure 129 Cards 6 Save the node. a. Click Save and Transfer at the bottom of the Edit web page b. Click OK to save this node. End of Procedure Configuring a card as a node Leader A Voice Gateway Media Card remains at the default “Follower” setting in a CS 1000E system. A Signaling Server is the IP telephony node Leader.
PAGE 323
Installing and configuring a Voice Gateway Media Card Page 323 of 466 Description, Installation, and Operation (NN43100-500) for a detailed configuration procedure. Configuring voice gateway channels using Element Manager The voice gateway channels are also called “DSP channels” or the card’s “physical TNs”. Follow Procedure 68 to configure the voice gateway channels using Element Manager. Note: The voice gateway channels can also be configured using LD 14.
PAGE 324
Page 324 of 466 Installing and configuring a Voice Gateway Media Card The Add VGW channels web page opens, as shown in Figure 131. Figure 131 Add VGW channels 5 Enter the appropriate parameters to configure the VGW channels. The TN is the logical TN of the first Voice Gateway Media Card unit. Note: The Media Card has 8 or 32 channels. The ITG-P card has 24 channels. 6 Click Submit. The VGW channels for this card are displayed. See Figure 132 on page 325.
PAGE 325
Installing and configuring a Voice Gateway Media Card Page 325 of 466 Figure 132 VGW channels list End of Procedure Configuring voice gateway channels using LD 14 The voice gateway channels are also called “DSP channels” or the card’s “physical TNs.” Follow Procedure 69 on page 326 to configure the voice gateway channels using LD 14. Note: The voice gateway channels can also be configured using Element Manager.
PAGE 326
Page 326 of 466 Installing and configuring a Voice Gateway Media Card Procedure 69 Configuring voice gateway channels using LD 14 1 Log in to the CS 1000E. a. Enter the command: LOGI System response: PASS? b. Enter the default password: 0000 2 Access LD 14. Enter the command: LD 14 3 Enter responses shown in Table 43. Table 43 LD 14 – Configure physical TNs (Part 1 of 2) Prompt Response Description REQ NEW 24 Create 24 voice Media Gateway channels on an ITG-P Line card.
PAGE 327
Installing and configuring a Voice Gateway Media Card Page 327 of 466 Table 43 LD 14 – Configure physical TNs (Part 2 of 2) Prompt Response Description MAXU 32 32 is the maximum number of voice Media Gateway channels on the Media Card. 24 24 is the maximum number of voice Media Gateway channels on the ITG-P Line card. IPTN YES ITG Physical TN. ZONE 0-255 Zone number to which the Voice Gateway Media Card Physical TNs belong. Verify that the zone exists in LD 117.
PAGE 328
Page 328 of 466 Installing and configuring a Voice Gateway Media Card Installing a CompactFlash The Voice Gateway Media Card requires a CompactFlash card to operate. The CompactFlash card contains the IP Line 3.1 software. CAUTION WITH ESDS DEVICES Wear an antistatic device to avoid damage to the Voice Gateway Media Card.
PAGE 329
Installing and configuring a Voice Gateway Media Card Page 329 of 466 Figure 133 CompactFlash card location CompactFlash card Figure 134 shows the CompactFlash card and Retaining Pin.
PAGE 330
Page 330 of 466 Installing and configuring a Voice Gateway Media Card Procedure 70 Installing the CompactFlash 1 Remove the Media Card, CompactFlash card, and Retaining Pin from the packaging. 2 Locate the CompactFlash socket in the lower left-hand corner of the Voice Gateway Media Card (see Figure 135). Figure 135 CompactFlash socket on Voice Gateway Media Card 3 Position the CompactFlash card with the label facing up and contact pins toward the socket, as shown in Figure 136.
PAGE 331
Installing and configuring a Voice Gateway Media Card 4 Page 331 of 466 Insert the CompactFlash card in the socket. Press firmly until it is fully seated and the Eject button extends (see Figure 137). Figure 137 Insert CompactFlash to extend Eject button Eject button 5 Turn the Voice Gateway Media Card over to view the back of the card. Identify the hole for the Retaining Pin. The hole (labeled a in Figure 138) is located approximately 1 inch (2.5 cm) above the lower lock latch and 1 inch (2.
PAGE 332
Page 332 of 466 Installing and configuring a Voice Gateway Media Card Press the Retaining Pin into the hole until the pin clicks as it locks into position (labeled 2 in Figure 139). The underside of the head of the Retaining Pin should be flat against the card. Figure 139 Inserting the Retaining Pin 7 Turn the card over to view the front of the card. Ensure the Retaining Pin is in place, as shown Figure 140 on page 332. Figure 140 Retaining Pin fully inserted End of Procedure NN43041-310 Standard 01.
PAGE 333
Installing and configuring a Voice Gateway Media Card Page 333 of 466 Installing a card in a Media Gateway A Voice Gateway Media Card can be installed in a Media Gateway or a Media Gateway Expander slot. See Figure 141 on page 333 and Figure 142 on page 334 to make sure that you insert the Voice Gateway Media Card in the correct slot. Note: See your installation worksheet, provided by your Planning and Engineering group for the correct slot for the Voice Gateway Media Cards.
PAGE 334
Page 334 of 466 Installing and configuring a Voice Gateway Media Card Figure 142 Media Gateway Expander card slot location SLOT 10 SLOT 9 SLOT 8 SLOT 7 Slot 10 Slot 9 Slot 8 Slot 7 553-CSE9032 Table 44 on page 335 shows the TN assignments for the MG 1000E. Communication Server 1000 Release 5.0 supports up to 30 MG 1000E. NN43041-310 Standard 01.
PAGE 335
Installing and configuring a Voice Gateway Media Card Page 335 of 466 Table 44 TN assignments for MG 1000E MG 1000E MG 1000E Expander Slots 1 2 3 4 7 8 9 10 TN lsc lsc lsc lsc lsc lsc lsc lsc MG 1000E 1 000 0 01 000 0 02 000 0 03 000 0 04 000 0 07 000 0 08 000 0 09 2 000 1 01 000 1 02 000 1 03 000 1 04 000 1 07 000 1 08 000 1 09 3 004 0 01 004 0 02 004 0 03 004 0 04 004 0 07 004 0 08 004 0 09 4 004 1 01 004 1 02 004 1 03 004 1 04 004 1 07 004 1 08 004 1 09 5 008 0 01 008 0 02 008 0 03
PAGE 336
Page 336 of 466 Installing and configuring a Voice Gateway Media Card c. Hook the locking devices. Note: The Voice Gateway Media Card boots automatically. If the Voice Gateway Media Card is a Follower, then it retrieves the node configuration files from the IP telephony node Leader. If it is a Leader, then you must configure it. See IP Line: Description, Installation, and Operation (NN43100-500) for a detailed configuration procedure. 2 Observe the Voice Gateway Media Card faceplate display.
PAGE 337
Installing and configuring a Voice Gateway Media Card Page 337 of 466 Figure 143 Node Maintenance and Reports web page 2 Open the desired node by clicking on the + next to the Node ID. This displays the Signaling Servers and Voice Gateway Media Cards belonging to the node, as shown in Figure 144 on page 337. Figure 144 Node Maintenance and Reports – expanded node 3 Click Status for the desired Voice Gateway Media Card. The output from this command is displayed in the window pane (result box).
PAGE 338
Page 338 of 466 Installing and configuring a Voice Gateway Media Card Where xx.xxx.xxx.xxx is the ELAN IP address of the Voice Gateway Media Card and the meaning of the status is: • Disabled – The card is configured but out-of-service. • Enabled – The card is configured and operational. • Unequipped – The card is not configured in the Call Server.
PAGE 339
Installing and configuring a Voice Gateway Media Card Page 339 of 466 Figure 145 General Commands 4 From the Group drop-down list, select Vgw. 5 From the Command drop-down list, select vgwShowAll. 6 Click RUN. Figure 146 on page 340 shows the General Commands web page with the output from the vgwShowAll command. The output shows information about all the voice gateway channels.
PAGE 340
Page 340 of 466 Installing and configuring a Voice Gateway Media Card Figure 146 vgwShowAll result The following information is provided for each VGW channel: • Chan – Channel number • ChanState – State of channel (Idle/Busy/Disabled/Unequipped) • DspMode – Mode DSP is in (Voice/Closed) • Codec – Codec frame-size used for the call • Tn – Channel's physical TN in packed format • Reg – Status of channel's gateway registration • Air Time – Duration of audio stream connection in seconds.
PAGE 341
Installing and configuring a Voice Gateway Media Card Page 341 of 466 Procedure 74 Displaying the status of Voice Gateway Media Card units 1 Select System > Maintenance from the navigator. The Maintenance web page opens as shown in Figure 147. This page allows you to perform maintenance using overlays or using a selected functionality. The default is overlay, as shown in Figure 147. Figure 147 Maintenance (by Overlay) web page 2 Select Select by Functionality.
PAGE 342
Page 342 of 466 Installing and configuring a Voice Gateway Media Card Figure 148 Maintenance (by functionality) web page 3 Select Network & Peripheral Equipment Diagnostics from the list in Figure 148. The Network and Peripheral Diagnostics web page opens, as shown in Figure 149 on page 343. NN43041-310 Standard 01.
PAGE 343
Installing and configuring a Voice Gateway Media Card Page 343 of 466 Figure 149 Network & Peripheral Diagnostics web page 4 Choose the STAT — Get card status command from the Card Commands drop-down list. 5 Enter the card number in the corresponding Command Parameter text box. 6 Click Submit to the right of the text box. The output from this command is shown in the text box in the lower half of the web page.
PAGE 344
Page 344 of 466 Installing and configuring a Voice Gateway Media Card Procedure 75 Displaying the status of one unit on a Voice Gateway Media Card 1 Select System > Maintenance from the navigator. The Maintenance web page opens as shown in Figure 147 on page 341. This page allows you to perform maintenance using overlays or using a selected functionality. The default is overlay, as shown in Figure 147. 2 Select Select by Functionality.
PAGE 345
Installing and configuring a Voice Gateway Media Card Page 345 of 466 The list in the web page changes to show a list of diagnostics you can use, as shown in Figure 148 on page 342. 3 Select Network & Peripheral Equipment Diagnostics from the list in Figure 148 on page 342. The Network and Peripheral Diagnostics web page opens, as shown in Figure 149 on page 343. 4 Select the DISC – Disable Peripheral card command from the Card Commands drop-down list.
PAGE 346
Page 346 of 466 Installing and configuring a Voice Gateway Media Card The Network and Peripheral Diagnostics web page opens, as shown in Figure 149 on page 343. 4 Select the DISU – Disable unit command from the Unit Commands drop-down list. 5 Enter the card number and unit number in the corresponding Command Parameter text box. 6 Click Submit to the right of the text box. The output from this command is shown in the text box in the lower half of the web page.
PAGE 347
Installing and configuring a Voice Gateway Media Card Page 347 of 466 The output from this command is shown in the text box in the lower half of the web page. End of Procedure Enabling a card unit Follow Procedure 79 to enable a Voice Gateway Media Card unit using Element Manager. Procedure 79 Enabling a Voice Gateway Media Card unit using Element Manager 1 Select System > Maintenance from the navigator. The Maintenance web page opens as shown in Figure 147 on page 341.
PAGE 348
Page 348 of 466 Installing and configuring a Voice Gateway Media Card Verifying functionality You can now use the Voice Gateway Media Card to transcode voice data between IP and TDM. To test the voice gateway channels (DSPs), perform a variety of analog or digital calls to IP Phones and vice-versa. Note: You require analog or digital telephones or trunks to perform this test.
PAGE 349
360 Page 349 of 466 Installing the Main Distribution Frame Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Terminal block requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Installing a BIX cross-connect terminal . . . . . . . . . . . . . . . . . . . . . . . . 350 Installing a Krone Test Jack Frame for the UK . . . . . . . . . . . . . . . . .
PAGE 350
Page 350 of 466 Installing the Main Distribution Frame Terminal block requirements The cross-connect terminal requires enough connecting blocks to terminate up to four 25 pair cables for each Media Gateway and each Media Gateway Expander. When Ethernet connections are used instead of traditional cabling, the Media Card Input/Output adapter is used: • For the 1.5 Mbit DTI/PRI circuit card NTRB21, use the NTBK04 cable. • For the 2.0 Mbit DTI circuit card NTAK10, 2.0 Mbit PRI circuit card NTAK79, and 2.
PAGE 351
Installing the Main Distribution Frame 3 Page 351 of 466 Attach labels on the cross-connect terminal to indicate the terminal blocks assigned to the following: • 25-pair cables from the system • AUX wiring • PFTUs • Telephones and consoles • Trunks • Miscellaneous equipment Figure 150 Typical BIX cross-connect terminal layout Media Gateway Cable Card 1 Cable Card 2 AUX cable PFTU Cable Card 3 Cable Card 4 Telephones Trunks and Miscellaneous Media Gateway Expansion Cable Card 7 Cable Card 8
PAGE 352
Page 352 of 466 Installing the Main Distribution Frame Installing a Krone Test Jack Frame for the UK The Krone Test Jack Frame provides terminating strips that hold ten pairs of cable. Generally, only eight of ten pairs are used. As a result, one 25-pair cable requires three terminating strips (8 pairs/strip x 3 strips = 24 pairs). Figure 151 on page 353 shows how one 25-pair cable is divided among three terminating strips on the Krone Test Jack Frame. NN43041-310 Standard 01.
PAGE 353
Installing the Main Distribution Frame Page 353 of 466 Figure 151 25-pair cable on three Krone strips Pair Pin Number Wire Colour Krone Strip 1T 1R 2T 2R 3T 3R 4T 4R 5T 5R 6T 6R 7T 7R 8T 8R 9T 9R 10T 10R 11T 11R 12T 12R 13T 13R 14T 14R 15T 15R 16T 16R 17T 17R 18T 18R 19T 19R 20T 20R 21T 21R 22T 22R 23T 23R 24T 24R 25T 25R 26 1 27 2 28 3 29 4 30 5 31 6 32 7 33 8 34 9 35 10 36 11 37 12 38 13 39 14 40 15 41 16 42 17 43 18 44 19 45 20 46 21 47 22 48 23 49 24 50 25 W-BL BL-W W-O O-W W-G G-W W-BR BR-W W-S S
PAGE 354
Page 354 of 466 Installing the Main Distribution Frame Procedure 81 describes how to install the Krone Test Jack Frame for the UK. For detailed information, refer to the Krone documentation. Procedure 81 Installing the Krone Test Jack Frame (UK) NN43041-310 1 Refer to the equipment layout plan to determine where to place the cross-connect terminal. 2 Lay out the terminal blocks as shown in Figure 152 on page 355.
PAGE 355
Installing the Main Distribution Frame Page 355 of 466 Figure 152 Typical Krone cross-connect terminal layout (UK) Pair Pair Spare Other equipment Media Gateway Expansion Media Gateway 17 9 1 1 17 9 1 17 9 1 17 9 1 17 9 1 17 9 1 9 9 1 1 9 1 17 9 1 17 9 1 17 9 1 PFTU termination AUX cable Grounding block Card J10 10 Card J9 9 Card 8 Card 7 Card 4 Card 3 Card 2 Card 1 24 16 8 6 24 16 8 24 16 8 24 16 8 24 16 8 24 16 8 16 16 8 8 16 8 24 16 8 24 16 8 24 16 8 553-CSE9033 End of Procedure Commun
PAGE 356
Page 356 of 466 Installing the Main Distribution Frame Connecting the cables to the Media Gateways DANGER Always use caution when installing or modifying telephone lines. Do not install telephone wiring during a lightning storm. Never touch uninsulated telephone wiring unless the line is disconnected at the network interface. Each Media Gateway and each Media Gateway Expander requires up to four 25-pair cables.
PAGE 357
Installing the Main Distribution Frame Page 357 of 466 Figure 153 Cable connectors at the back of the Media Gateway Car d 4 25-pair connectors Card 1 Card 2 Card 3 Figure 154 Cable connectors at the back of the Media Gateway Expander Ca 10 d 9 rd Car C ar d Ca r 8 d 7 25-pair connectors Communication Server 1000E Installation and Commissioning
PAGE 358
Page 358 of 466 Installing the Main Distribution Frame 4 Tighten the velcro straps when you have connected each cable to the system. 5 Terminate all the 25-pair cables installed at the cross-connect terminal. 6 Label all the cables at the cross-connect terminal blocks according to the card slot assignment plan. 7 Connect the AUX cable in the upper 9-pin connector located on the top left-hand side of the Media Gateway. See Figure 155 on page 358.
PAGE 359
Installing the Main Distribution Frame 8 Page 359 of 466 When auxiliary power is required from the QUA6 PFTU, terminate the AUX cable at the PFTU cross-connect terminal, according to Table 45.
PAGE 360
Page 360 of 466 NN43041-310 Installing the Main Distribution Frame Standard 01.
PAGE 361
378 Page 361 of 466 Configuring an IP telephony node Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 Configuring MS Internet Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Logging in to Element Manager . . . . . . . . . . . . . . . . . . . . . . .
PAGE 362
Page 362 of 466 Configuring an IP telephony node The preconfigured IP telephony configuration files from the leader Signaling Server must be imported. These files are saved on the CS 1000E as: • c:/u/db/node/nodex.cfg where x is the node number • c:/u/db/node/nodex.btp where x is the node number IMPORTANT! Do not attempt to alter the configuration files either manually or with OTM’s ITG or IP Phone management. Use Element Manager only.
PAGE 363
Configuring an IP telephony node Page 363 of 466 Limited Access to Overlays, see Features and Services (NN43001-106) and Software Input/Output: Administration (NN43001-611). Configuring MS Internet Explorer Element Manager is available to configure IP telephony parameters on the system. It is accessed by pointing MS Internet Explorer (version 6.0.2600 or higher) to the ELAN subnet, TLAN subnet, or node IP address of the Signaling Server. Note: Element Manager requires Microsoft Internet Explorer 6.0.
PAGE 364
Page 364 of 466 Configuring an IP telephony node Figure 156 Internet Explorer – Internet Options 3 NN43041-310 On the General tab, under the Temporary Internet files section, click Settings. The Settings window opens (see Figure 157 on page 365). Standard 01.
PAGE 365
Configuring an IP telephony node Page 365 of 466 Figure 157 Temporary Internet files – Settings window 4 Click Every visit to the page. This checks for new versions of stored pages on every visit to the web page. 5 Click OK in the Settings window. 6 Click OK in the Internet Options window.
PAGE 366
Page 366 of 466 Configuring an IP telephony node Logging in to Element Manager Follow Procedure 84 to log in to Element Manager. Procedure 84 Logging in to Element Manager 1 Open the web browser. 2 Enter the Signaling Server Node IP address in the Address Bar of the browser window, and press Enter on the keyboard. Note: This address can be the ELAN IP, TLAN IP, or Node IP, depending on the network in use.
PAGE 367
Configuring an IP telephony node Page 367 of 466 Figure 158 Element Manager login End of Procedure Communication Server 1000E Installation and Commissioning
PAGE 368
Page 368 of 466 Configuring an IP telephony node Importing preconfigured IP telephony files Follow Procedure 85 to import the preconfigured IP telephony files from the Signaling Server. Procedure 85 Importing an existing node Figure 159 displays the Element Manager System Information home page. Figure 159 Element Manager – System Overview web page NN43041-310 Standard 01.
PAGE 369
Configuring an IP telephony node 1 Page 369 of 466 Select IP Network > Node: Servers, Media Cards from the navigator. The Node Configuration web page opens, as shown in Figure 160. If this is the first node to be added, the “No nodes are configured” message is displayed. Figure 160 Node Configuration web page 2 Import the Node files from the leader Signaling Server. a. Click Import Node Files. The Import Node Files screen as shown in Figure 161 on page 370 appears. b.
PAGE 370
Page 370 of 466 Configuring an IP telephony node Figure 161 Import Node Files web page 3 Click Import. Click OK in the dialog when the operation is complete. The Node Summary web page is re-displayed showing the new node. End of Procedure Reviewing and submitting IP telephony node configuration files Follow Procedure 86 to review and submit IP telephony node configuration files.
PAGE 371
Configuring an IP telephony node Page 371 of 466 Note 1: Clicking Transfer / Status displays the Transfer / Status web page (see Figure 165 on page 373). This sends the node configuration files to all IP Telephony components in the node. • If any element within the node fails to transfer either BOOTP or CONFIG files, Transfer / Status is highlighted in red. • Transfer / Status is highlighted in yellow if the transfer status of the node elements is unavailable.
PAGE 372
Page 372 of 466 Configuring an IP telephony node Figure 162 Transfer Progress – Starting Figure 163 Transfer Progress – Transferring When the file transfer is complete, the Transfer Progress web page displays a status of complete (see Figure 164 on page 373). NN43041-310 Standard 01.
PAGE 373
Configuring an IP telephony node Page 373 of 466 Figure 164 Transfer Progress – Complete 5 Click OK in the dialog box. The Transfer / Status web page displays. Note: The Transfer / Status web page (see Figure 165) can also be displayed from the Node Summary web page by clicking Transfer / Status. This web page indicates if the transfer was successful or not. For example, Figure 165 shows some elements as unreachable; you can transfer to these elements again.
PAGE 374
Page 374 of 466 Configuring an IP telephony node The previous status of the node displays, and the failure reason is displayed for elements in nodes that failed to get configuration files (BOOTP.TAB and CONFIG.INI) from the CS 1000E. The Transfer / Status web page has five buttons: 6 • Selected All. Selects all the elements in the node (that is, it adds a check mark in each element’s check box). • Unselect All.
PAGE 375
Configuring an IP telephony node Page 375 of 466 In Element Manager: 1 Click Edit on the Node Configuration web page (see Figure 160 on page 369). 2 Click Add beside the Signaling Server row. 3 Enter the Follower Signaling Server data to an IP telephony node. Include the ELAN MAC address (used to answer BootP requests). 4 Click Save and Transfer to save the changes and the Leader Signaling Server then obtains a copy of the node files.
PAGE 376
Page 376 of 466 Configuring an IP telephony node datadump backs up new IP Telephony node files on the CS 1000E at the same time that it backs up the customer database. Procedure 88 Performing a datadump using Element Manager From within Element Manager (see Figure 84 on page 366 for details on logging in), do the following: 1 Choose Tools > Backup and Restore > Call Server from the navigator. 2 The Call Server Backup and Restore web page opens, as shown in Figure 57 on page 172. 3 Select Backup.
PAGE 377
Configuring an IP telephony node Page 377 of 466 End of Procedure Communication Server 1000E Installation and Commissioning
PAGE 378
Page 378 of 466 NN43041-310 Configuring an IP telephony node Standard 01.
PAGE 379
390 Page 379 of 466 Installing Line cards and cross-connecting telephones Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Card placement in a Media Gateway or a Media Gateway Expansion . 382 Cross-connecting telephones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Connecting a telephone without a PFTU . . . . . . . . . . . . . . . . . . . . . . .
PAGE 380
Page 380 of 466 Installing Line cards and cross-connecting telephones Before you proceed, install the cable from the slot that contains the Line card associated with the telephone being connected. Refer to “Installing the Main Distribution Frame” on page 349, if you require additional cable installation. DANGER OF ELECTRIC SHOCK Always use caution when installing or modifying telephone lines. Do not install telephone wiring during a lightning storm.
PAGE 381
Installing Line cards and cross-connecting telephones Page 381 of 466 Figure 167 Circuit card assignments in a Media Gateway SLOT 4 SLOT 3 SLOT 2 SLOT 1 SLOT 0 SSC Slot 4 Slot 3 Slot 2 Slot 1 Slot 0 - SSC 553-CSE9025 Figure 168 Circuit card assignments in a Media Gateway Expander SLOT 10 SLOT 9 SLOT 8 SLOT 7 Slot 10 Slot 9 Slot 8 Slot 7 553-CSE9032 Communication Server 1000E Installation and Commissioning
PAGE 382
Page 382 of 466 Installing Line cards and cross-connecting telephones Circuit cards features If a circuit card has a switch symbol on its faceplate, it is equipped with option switches, strapping plugs, or both. Make sure that the circuit cards with option switches or strapping plugs are set correctly. Some circuit cards can have daughterboards and other add-on devices installed on them.
PAGE 383
Installing Line cards and cross-connecting telephones Page 383 of 466 Figure 169 NE-500/2500-type telephone cross connections Lead designation Cable pairs Line Pack Unit 0 Unit 1 Unit 2 Unit 3 Unit 4 Unit 5 Unit 6 Unit 7 Unit 8 Unit 9 Unit 10 Unit 11 Unit 12 Unit 13 Unit 14 Unit 15 Cross connect terminal W-BL BL-W W-O O-W T R T R To 500/2500-type telephone To 500/2500-type telephone W-G G-W W-BR BR-W T R T R To 500/2500-type telephone To 500/2500-type telephone W-S S-W R-BL BL-R T R T R To 500/2
PAGE 384
Page 384 of 466 Installing Line cards and cross-connecting telephones Figure 170 Digital telephone cross connections Pack connector Telephone connecting block, or connector PE shelf Line pack Cross connect block Unit 0 T0 R0 26 1 Unit 1 T1 R1 27 2 Unit 14 T14 R14 Unit 15 T15 R15 Part of 25 pair cable W-BL BL-W T0 R0 W-O O-W T1 R1 40 15 BK-S S-BK T14 R14 40 Y-BL T15 16 BL-Y R15 Shelf connector G R W B Part of 25 pair cable Line cord to telephone For Power Supply leads to tel
PAGE 385
Installing Line cards and cross-connecting telephones Page 385 of 466 Procedure 90 Connecting a telephone without a PFTU 1 Locate the telephone terminations on the cross-connect terminal. 2 Connect one end of the cross-connect wire to the leads of the telephone. 3 Locate the Line card terminations on the cross-connect terminal. 4 Connect the other end of the cross-connect wire to the assigned TN terminal block. 5 Activate the telephone.
PAGE 386
Page 386 of 466 Installing Line cards and cross-connecting telephones Procedure 91 Connecting an off-premise telephone 1 Install the NTAK92BA Off-Premise Protection Module on the wall using four #10 1/2-in (minimum) screws. 2 Connect a #6 AWG from the grounding lug at the bottom of the NTAK92AA Off-Premise Protection Module to the system ground. Refer to Figure 171 on page 387.
PAGE 387
Installing Line cards and cross-connecting telephones Page 387 of 466 Figure 171 NTAK92BA Off-Premise Protection Module connections Cross-connect terminal block J2 NTAK92AA Off-Premise Protection Module J1 Ground lug Connector J2 BL - 1W BL - 2W O - 1W O - 2W G - 1W G - 2W BR - 1W BR - 2W T1 R1 T2 R2 To off-premise T3 telephones R3 T4 R4 BL - 1W BL - 2W O - 1W O - 2W G - 1W G - 2W BR - 1W BR - 2W T1 R1 T2 To analogue R2 line card in T3 Option 11 R3 cabinet T4 R4 Connector J1 NTAK9204 Cable NTAK9
PAGE 388
Page 388 of 466 Installing Line cards and cross-connecting telephones Figure 172 Attendant console connections Cross-connect block To 1st TN W-BL BL-W To 2nd TN W-O O-W ASM/ ADN To 3rd TN Console power from AUX cable (one console only) To +15 AUX (W-G 1 dot wire) on AUX cable + AUX To -15 AUX (G-W 1 dot wire) on AUX cable - AUX GND TC Note: As an alternative, console power can be obtained from the 4 th and 5 th TNs on the circuit card.
PAGE 389
Installing Line cards and cross-connecting telephones Page 389 of 466 Table 46 Color combinations of cable pairs Color W-Bl Bl-W W-O O-W W-G G-W W-BR BR-W W-S S-W R-BL BL-R R-O O-R R-G G-R Unit 0 1 2 3 4 5 6 7 Color R-BR BR-R R-S S-R BK-BL BL-BK BK-O O-BK BK-G G-BK BK-BR BR-BK BK-S S-BK Y-B B-Y Unit 8 9 10 11 12 12 14 15 End of Procedure Communication Server 1000E Installation and Commissioning
PAGE 390
Page 390 of 466 NN43041-310 Installing Line cards and cross-connecting telephones Standard 01.
PAGE 391
436 Page 391 of 466 Installing and configuring Nortel IP Phones Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Configuring VoIP bandwidth management zones . . . . . . . . . . . . . . . . 406 Configuring virtual superloops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Configuring a Nortel IP Phone using LD 11. . . . . . . . . . . . . . . . . . . . .
PAGE 392
Page 392 of 466 Installing and configuring Nortel IP Phones Introduction For detailed information on the various telephones supported on the CS 1000E system, refer to Telephones and Consoles: Description, Installation, and Operation (NN43001-567) and IP Phones: Description, Installation, and Operation (NN43001-368).
PAGE 393
Installing and configuring Nortel IP Phones Page 393 of 466 Package components for the Nortel IP Phones Table 47 lists the Nortel IP Phone 2001 package components and product codes. Table 47 Nortel IP Phone 2001 components list (Part 1 of 2) Nortel IP Phone 2001 package contents include: • Nortel IP Phone 2001 • Handset • Handset cord • Footstand • 7 ft.
PAGE 394
Page 394 of 466 Installing and configuring Nortel IP Phones Table 47 Nortel IP Phone 2001 components list (Part 2 of 2) Handset, Charcoal A0758634 Handset cord, Ethergray; for Nortel IP Phone 2004 and Nortel IP Phone 2001 A088682 Handset cord, Charcoal; for Nortel IP Phone 2004 and Nortel IP Phone 2001 N0000764 Nortel IP Phone 2001/2002/2004 Power Adapters Power transformer (117/120 VAC 50/60 Hz) (North America) A0619627 Power transformer 3 prong AC to AC, direct plug-in, 8W, 240 VAC, 50Hz to 16 V
PAGE 395
Installing and configuring Nortel IP Phones Page 395 of 466 Table 48 lists the Nortel IP Phone 2002 package components and product codes.
PAGE 396
Page 396 of 466 Installing and configuring Nortel IP Phones Table 48 Nortel IP Phone 2002 components list (Part 2 of 2) Handset cord, Ethergray A0897725 Handset cord, Charcoal N0000763 Footstand, Charcoal (used for Ethergray and Charcoal models) A0891619 IP Phone 2001/2002/2004 Power Adaptors Power transformer (117/120 VAC 50/60 Hz) (North America) A0619627 Power transformer 3 prong AC to AC, direct plug-in, 8W, 240 VAC, 50Hz to 16 VAC at 500 mA (Ireland and UK) A0656598 Power transformer AC to
PAGE 397
Installing and configuring Nortel IP Phones Page 397 of 466 Table 49 lists the Nortel IP Phone 2004 package components and product codes. Table 49 IP Phone 2004 component list (Part 1 of 2) IP Phone 2004package contents includes • IP Phone 2004 • Handset • Handset cord • Footstand • 7 ft.
PAGE 398
Page 398 of 466 Installing and configuring Nortel IP Phones Table 49 IP Phone 2004 component list (Part 2 of 2) Replacement parts 7 ft.
PAGE 399
Installing and configuring Nortel IP Phones Page 399 of 466 Table 50 lists the Nortel IP Phone 2007 package components and product codes. Table 50 Nortel IP Phone 2007 component list (Part 1 of 2) Nortel IP Phone 2007 package contents includes NTDU96AB70 • Nortel IP Phone 2007(charcoal with metallic bezel) • Handset • Handset cord • Footstand • 7 ft. (2.3 m) CAT5 Ethernet cable • Getting Started card Replacement parts 7 ft.
PAGE 400
Page 400 of 466 Installing and configuring Nortel IP Phones Table 50 Nortel IP Phone 2007 component list (Part 2 of 2) Option 11C UK Power Cord 240Vac Hong Kong, Ireland, UK, Singapore, Malaysia, India, Bangladesh, Pakistan, Brunei, Sri Lanka NTTK18AB Option 11C Denmark Power Cord Kit, 9.9 ft. 125Vac Denmark NTTK22AB Table 51 lists the Nortel IP Phone ACP 2033 package components and product codes.
PAGE 401
Installing and configuring Nortel IP Phones Page 401 of 466 NA NEMA 5-15P, 125V 13A (10ft.) NTTK14AB Euro CEE (7) VII, 250V, 10A (2.5m) NTTK16AB ANZ AS3112, 250V 10A (2.5m) NTTK15AA Swiss SEV 1011, 250V 10A (8ft.) NTTK17AB UK/Ireland BS1363, 240V 10A (8ft.) NTTK18AB Denmark AFSNIT, 250V 10A (2.5m) NTTK22AB Argentina IRAM 2073, 250V 10A (8ft.) A0814961 Table 52 lists the Package components for the WLAN Handsets.
PAGE 402
Page 402 of 466 Installing and configuring Nortel IP Phones Table 52 WLAN Handset component list (Part 2 of 4) WLAN Handset 2211 kit North America) NTTQ50AA/A0548451 WLAN Handset 2211 kit Global (power supply not included NTTQ50BA/A0548455 North American kit includes: WLAN 2211 Handset NTTQ5010/A0548452 WLAN Handset 2211 Battery Pack NTTQ5050/A0548453 WLAN Handset 2211 Desktop Charger NTTQ5060/A0548454 WLAN 2210/2211 Charger & WLAN Application Gateway 2246-64 Power Supply for North America NTTQ
PAGE 403
Installing and configuring Nortel IP Phones Page 403 of 466 Table 52 WLAN Handset component list (Part 3 of 4) WLAN Application Gateway 2246 64 users NTTQ65AB/N0023211 128 users NTTQ65BA/A0548971 256 users NTTQ65CA/A0548972 512 users NTTQ65DA/A0548973 1,024 users NTTQ65EA/A0548974 10,000+ users NTTQ65FA/A0548975 The following items must be ordered with the applicable power supply: WLAN Handset 2210 Desktop Charger WLAN Handset 2211 Desktop Charger WLAN Handset 2211 Gang Charger WLAN IP Telepho
PAGE 404
Page 404 of 466 Installing and configuring Nortel IP Phones Table 52 WLAN Handset component list (Part 4 of 4) Power supplies — WLAN Handset 2211 Gang Charger: • North America NTTQ4301/A0548951 • Europe NTTQ4311/A0548952 • UK-HK NTTQ4321/A0548953 • Switzerland NTTQ4331/A0548954 • Australia-New Zealand NTTQ4341/A0548955 • Mexico NTTQ4351 WLAN Handset 2210/2211 Charger & WLAN Application Gateway 2246-64: • North America NTTQ4101/A0548499 NTTQ4111/A0548956 • Europe NTTQ4121/A0548958 • UK-HK
PAGE 405
Installing and configuring Nortel IP Phones Page 405 of 466 Connectivity and power requirements Each Nortel IP Phone requires: • a dedicated 10BaseT or 100BaseT or 10/100BaseT Ethernet interface • a small desktop hub or switch if sharing an existing desktop Ethernet connection with a PC. • a local power supply appropriate for the voltage in the area or a Power over LAN unit. (The Nortel IP Phone 2002 comes with a built-in 3-port switch and is ready for LAN powering.
PAGE 406
Page 406 of 466 Installing and configuring Nortel IP Phones • Procedure 105: "Displaying registered IP Phones in Element Manager" on page 436 Configuring VoIP bandwidth management zones Follow Procedure 93 to configure the VoIP bandwidth management zones. For more details on bandwidth management zones, see IP Line: Description, Installation, and Operation (NN43100-500). VoIP bandwidth management zones can be configured with Element Manager or using the CLI.
PAGE 407
Installing and configuring Nortel IP Phones 5 Page 407 of 466 Exit from LD 117. Enter the command: **** Table 53 Bandwidth management zones configuration commands in LD 117 Command Description NEW ZONE xxx p1 p2 p3 p4 p5 Create a new zone, where: xxx = zone number = (0) - 255.
PAGE 408
Page 408 of 466 Installing and configuring Nortel IP Phones End of Procedure Configuring virtual superloops Follow Procedure 94 to configure the virtual superloops. For more details on virtual superloops, see IP Line: Description, Installation, and Operation (NN43100-500). Procedure 94 Configuring virtual superloops 1 Access LD 97. Enter the command: LD 97 2 Enter responses shown in Table 54. Table 54 LD 97 – Configure a Virtual Superloop.
PAGE 409
Installing and configuring Nortel IP Phones Page 409 of 466 Procedure 95 Configuring the IP Phones 1 Access LD 11. Enter the command: LD 11 2 Enter the appropriate responses shown in Table 55.
PAGE 410
Page 410 of 466 Installing and configuring Nortel IP Phones Table 55 LD 11 – Configure a Nortel IP Phone (Part 2 of 4) Prompt Response Description CLS ADD Class of Service ADD - Automatic Digit Display, (default for Nortel IP Phone) For a complete list of responses, refer to Software Input/ Output: Administration (NN43001-611). KEY xx aaa yyyy (cccc or D) zz..z Telephone function key assignments The following key assignments determine calling options and features available to a telephone.
PAGE 411
Installing and configuring Nortel IP Phones Page 411 of 466 Table 55 LD 11 – Configure a Nortel IP Phone (Part 3 of 4) Prompt Response Description Key number limits that can be assigned are as follows: 0-7 for Meridian Communications Adapter (MCA) 0-5 for M2006 0-7 for M2008 0-59 for M2616, varies with number of add-on modules 0-79 for I2002, varies with value of KEM 0-79 for I2004, varies with value of KEM Note: The first Nortel IP Phone KEM is assigned keys 32-55, and the second Nortel IP Phone KEM is
PAGE 412
Page 412 of 466 Installing and configuring Nortel IP Phones Table 55 LD 11 – Configure a Nortel IP Phone (Part 4 of 4) Prompt Response Description On the M3903, keys 4-15 are blocked. No feature assignment is accepted for keys 2-15. On the M3903, M3904, and M3905, keys 29-31 are reserved. No feature assignment is accepted for keys 29-31 other than NUL. On M3904, no feature assignment is accepted for keys 12-15. On M3905, the technician can assign NUL or a server application on key 5.
PAGE 413
Installing and configuring Nortel IP Phones 3 Page 413 of 466 Configure the dedicated soft keys, as shown in Table 56.
PAGE 414
Page 414 of 466 Installing and configuring Nortel IP Phones Table 56 Nortel IP Phone dedicated soft key assignment (Part 2 of 2) Nortel IP Phone key number Response(s) Allowed Key 25 CHG, NUL CHG – Charge Account key Key 26 CPN, NUL CPN – Calling Party Number key 4 Repeat Steps 2 and 3 for each Nortel IP Phone.
PAGE 415
Installing and configuring Nortel IP Phones Page 415 of 466 3 Click the desired node to expand it. 4 Click GEN CMD for the chosen Signaling Server or Media Card. The General Commands web page opens, as shown in Figure 173. Figure 173 General Commands 5 Select NodePwd from the Group drop-down list. 6 Select nodePwdShow from the Command drop-down list. 7 Click RUN. The current node password information displays in the text area at the bottom of the web page.
PAGE 416
Page 416 of 466 Installing and configuring Nortel IP Phones 9 Enter the administrator Nortel IP Phone Installer Password in the Node Password box (see Figure 174). Figure 174 Node Password Note: The entered password appears as asterisks. The valid characters are 0-9 * #. The password can be null or 6 to 14 digits in length. WARNING If the administrator password is null (zero length), then the Node ID, TN, and Password screens are not displayed on the IP Phones during their registration process.
PAGE 417
Installing and configuring Nortel IP Phones Page 417 of 466 The temporary password is set. Figure 175 Node Temp Password Note 1: The entered password appears as asterisks. The valid characters are 0-9 * #. The password can be 6 to 14 digits in length. Note 2: The temporary password automatically deletes itself after it has been used the defined number of times or when the duration expires, whichever comes first. 15 Select NodePwd from the Group drop-down list.
PAGE 418
Page 418 of 466 Installing and configuring Nortel IP Phones f. Handset cord Figure 176 Nortel IP Phone 2004 components Three Port Switch Power Transformer connection Power Splitter connection (power over LAN) CAT5 line cable NN43041-310 Standard 01.
PAGE 419
Installing and configuring Nortel IP Phones Page 419 of 466 2 Connect one end of the CAT5 line cable to the Ethernet jack at the back of the telephone. See Figure 176 on page 418. 3 Connect the other end into the IP voice network (Ethernet), using an RJ-45 connector. See Figure 177 on page 420. WARNING Do not plug the Nortel IP Phone into an ISDN connection. Severe damage can result. Consult the system administrator to ensure that the telephone is being plugged in to a 10/100BaseT Ethernet jack.
PAGE 420
Page 420 of 466 Installing and configuring Nortel IP Phones Figure 177 Nortel IP Phone connections End of Procedure NN43041-310 Standard 01.
PAGE 421
Installing and configuring Nortel IP Phones Page 421 of 466 Configuring the Nortel IP Phone boot parameters The Nortel IP Phone boot parameters are configured during telephone installation. The following configuration modes are available: • Manual configuration — All of the Nortel IP Phone's boot parameters are statically configured at the Nortel IP Phone. — See Procedure 98: "Entering IP Telephone boot parameters using manual configuration" on page 422.
PAGE 422
Page 422 of 466 Installing and configuring Nortel IP Phones Entering Nortel IP Phone boot parameters using manual configuration Follow Procedure 98 to enter IP Telephone boot parameters using manual configuration. Procedure 98 Entering IP Telephone boot parameters using manual configuration 1 Power the Nortel IP Phone. Within four seconds, the Nortel logo appears.
PAGE 423
Installing and configuring Nortel IP Phones 7 Page 423 of 466 Enter the default gateway. The Nortel IP Phone prompts: S1 IP: x.x.x.x 8 Enter the Server 1 IP (node IP). The Nortel IP Phone prompts: S1 PORT: 4100 9 Enter the Server 1 port. The Nortel IP Phone prompts: S1 ACTION: 1 10 Enter the Server 1 action. The Nortel IP Phone prompts: S1 RETRY COUNT: 10 11 Enter the Server 1 retry count. The Nortel IP Phone prompts: S2 ... 12 Enter same information as for Server 1.
PAGE 424
Page 424 of 466 Installing and configuring Nortel IP Phones b. Enter 1 to configure manual VLAN. The Nortel IP Phone prompts: VLAN: x Go to step 14 on page 424. c. Press the OK key. The Nortel IP Phone prompts: Invalid TN: x.x Reason: Unequipped. Go offhook to do SBI 14 Enter the VLAN ID. The Nortel IP Phone displays: Locating server... If you did not configure an Nortel IP Phone Installer Password, after several seconds, the Nortel IP Phone prompts: Node: x TN: x.
PAGE 425
Installing and configuring Nortel IP Phones Page 425 of 466 17 Enter the Nortel IP Phone’s (virtual) TN. The Nortel IP Phone displays the logo, the date and time, and the DN keys. 18 Check for dial tone and the correct DN above the display. End of Procedure Entering Nortel IP Phone boot parameters using full DHCP parameters Follow Procedure 99 to enter IP Phone boot parameters using full DHCP parameters.
PAGE 426
Page 426 of 466 Installing and configuring Nortel IP Phones VLAN?(0-No,1-Ma,2-Au)0 6 Choose one of the following: a. Enter 0 to configure no VLAN. The Nortel IP Phone displays: Locating server... After several seconds, the Nortel IP Phone prompts: Connect Svc Node: x TN: x.x Go to step 7 on page 426. b. Enter 1 to configure manual VLAN. The Nortel IP Phone prompts: VLAN: x Go to step 7. c. Enter 2 to configure automatic VLAN. The Nortel IP Phone prompts: VLAN: x Go to step 7 7 Enter the VLAN ID.
PAGE 427
Installing and configuring Nortel IP Phones 9 Page 427 of 466 Enter the node number and the temporary or administrator Nortel IP Phone Installer Password. Note 1: An asterisk is displayed for each password digit entered; the actual password is not displayed. Note 2: If this screen times out, or if you do not successfully enter the password in three attempts, the Nortel IP Phone continues its registration process as if no entry had been made to this prompt.
PAGE 428
Page 428 of 466 Installing and configuring Nortel IP Phones c. Press the OK key to accept your selection. The Nortel IP Phone prompts: DHCP? (0-No, 1-Yes): 0 4 Enter 1 to use DHCP. The Nortel IP Phone prompts: DHCP:0-Full, 1-Partial:0 5 Enter the 1 to use Partial DHCP. The Nortel IP Phone prompts: S1 IP: x.x.x.x 6 Enter the Server 1 IP (node IP). The Nortel IP Phone prompts: S1 PORT: 4100 7 Enter the Server 1 port. The Nortel IP Phone prompts: S1 ACTION: 1 8 Enter the Server 1 action.
PAGE 429
Installing and configuring Nortel IP Phones Page 429 of 466 11 Choose one of the following: a. Enter 0 to configure no VLAN. The Nortel IP Phone displays: Locating server... After several seconds, the Nortel IP Phone prompts: Connect Svc Node: x TN: x.x Go to step 12. b. Enter 1 to configure manual VLAN. The Nortel IP Phone prompts: VLAN: x Go to step 12 on page 429. c. Enter 2 to configure automatic VLAN. The Nortel IP Phone prompts: VLAN: x Go to step 12. 12 Enter the VLAN ID.
PAGE 430
Page 430 of 466 Installing and configuring Nortel IP Phones 14 Enter the node number and the temporary or administrator Nortel IP Phone Installer Password. Note 1: An asterisk is displayed for each password digit entered; the actual password is not displayed. Note 2: If this screen times out, or if you do not successfully enter the password in three attempts, the Nortel IP Phone continues its registration process as if no entry had been made to this prompt.
PAGE 431
Installing and configuring Nortel IP Phones Page 431 of 466 Node: x TN: x.x 1 Enter the node number and the Nortel IP Phone's (virtual) TN, then go to Step 4. If you configured a Nortel IP Phone Installer Password, the Nortel IP Phone prompts: Node: x PassWord: 0 2 Enter the node number and the temporary or administrator Nortel IP Phone Installer Password. Note 1: An asterisk is displayed for each password digit entered; the actual password is not displayed.
PAGE 432
Page 432 of 466 Installing and configuring Nortel IP Phones The system response, displayed on the Nortel IP Phone, is as follows: OK, EXTENSION? 2244 10 Press the # key to select the default DN, or enter a DN and press #. 11 Listen for a relocation tone. The system response, displayed on the Nortel IP Phone, is as follows: OK 12 Replace the handset. The set displays the logo, the date and time, and the DN keys The set based installation is complete.
PAGE 433
Installing and configuring Nortel IP Phones Page 433 of 466 Procedure 102 Configuring the IP Softphone 2050 1 Access LD 11. Enter the command: LD 11 2 Enter appropriate responses shown in Table 57. Table 57 LD 11 – Configure the IP Softphone 2050 Prompt Response Description REQ: NEW CHG Add new data Change existing data TYPE: I2050pc Type of data block TN lscu Terminal number DES x...
PAGE 434
Page 434 of 466 Installing and configuring Nortel IP Phones installed, you can still choose it as the audio device from the Configuration Utility. Procedure 103 Installing the USB Headset Kit 1 Connect the coiled lower cord to the headset cord with the Quick Disconnect connector. Ensure the Quick Disconnect is securely fastened. 2 Connect the headset cord to the RJ9 jack on the adaptor. 3 Connect the USB cable to the headset adaptor and to one of the USB jacks at the back of your PC or USB hub.
PAGE 435
Installing and configuring Nortel IP Phones Page 435 of 466 Running the IP Softphone 2050 for the first time Installation places the IP Softphone 2050 in the Windows Start menu at Start > Programs > Nortel > IP Softphone 2050. The Configuration Utility is placed in the Windows Control Panel. The IP Softphone 2050 application is started by one of the following: • Select Start > Programs > Nortel > IP Softphone 2050. • Click the desktop shortcut (if one was created during the installation).
PAGE 436
Page 436 of 466 Installing and configuring Nortel IP Phones Verifying Nortel IP Phone functionality You can now use the IP Phones. To test the telephones, make Nortel IP Phone-to-Nortel IP Phone calls. Displaying registered IP Phones Follow Procedure 105 to display the IP Phones registered on a Signaling Server or Voice Gateway Media Card. Procedure 105 Displaying registered IP Phones in Element Manager 1 Log in to Element Manager.
PAGE 437
450 Page 437 of 466 Installing and cross-connecting a Power Fail Transfer Unit Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 Installing and connecting a QUA6 PFTU . . . . . . . . . . . . . . . . . . . . . . . 438 Installing and connecting a third-party PFTU. . . . . . . . . . . . . . . . . . . . 443 Connecting an analog (500/2500-type) telephone to a PFTU. . . . . . . .
PAGE 438
Page 438 of 466 Installing and cross-connecting a Power Fail Transfer Unit The following procedures are provided in this chapter: 1 Procedure 106: "Installing and connecting a QUA6 PFTU" on page 438 2 Procedure 107: "Connecting an analog (500/2500-type) telephone to a PFTU" on page 446 3 Procedure 108: "Connecting a Trunk to a PFTU" on page 448 Installing and connecting a QUA6 PFTU Follow Procedure 106 to install and connect a QUA6 PFTU.
PAGE 439
Installing and cross-connecting a Power Fail Transfer Unit 4 Page 439 of 466 Connect the PFTU power and control connections to the AUX connector on the Media Gateway. See Figure 179 on page 439 and Figure 180 on page 440, Table 58 on page 440, and Figure 181 on page 442.
PAGE 440
Page 440 of 466 Installing and cross-connecting a Power Fail Transfer Unit Figure 180 AUX cable connector on Media Gateway Table 58 Control and power connections on cable J1 (Part 1 of 2) J1 Cable from QUA6 Function Control NN43041-310 Pair Number Pair Color Connects to 1T W-BL (ALM) Not used 1R BL-W BRTN W-BL 1-dot connection on AUX cable 2T W-O PFTS W-O 1-dot connection on AUX cable. Transfer begins by applying ground to this lead. 2R O-W BRTN BL-W 1-dot connection on AUX cable.
PAGE 441
Installing and cross-connecting a Power Fail Transfer Unit Page 441 of 466 Table 58 Control and power connections on cable J1 (Part 2 of 2) J1 Cable from QUA6 Function PFTU power Pair Number Pair Color Connects to 3T W-G (TC) 3R G-W Not used 4T W-BR Not used 4R BR-W Not used 25T 25R S-V V-S -48 V -48 V Communication Server 1000E Cross-connects to Console transfer switch. See console connections. Transfer begins by applying ground to this lead. O-W 1-dot connection on AUX cable.
PAGE 442
Page 442 of 466 Installing and cross-connecting a Power Fail Transfer Unit Figure 181 Power fail transfer QUA6A PFTU XFER A W- BL- O- W- G- WU BL W W O W G X P F T U T R T 1 1 2 R T R 2 3 3 J1 TR 2 3 4 PFT1 5 5 2 2 V V NTAK1104 553-CSE8343 End of Procedure NN43041-310 Standard 01.
PAGE 443
Installing and cross-connecting a Power Fail Transfer Unit Page 443 of 466 Installing and connecting a third-party PFTU Follow the equipment manufacturer’s instructions for installing the PFTU. Use the information in Table 59 to connect a third-party PFTU. Table 59 PFTU control lead signals Lead State NTAK1104 AUX cable lead When PFTU is in non-transferred state When PFTU is in transferred state BRTN GROUND GROUND BRTN GROUND GROUND -48V AUX -48V DC (250 mA max.) -48V DC (250 mA max.
PAGE 444
Page 444 of 466 Installing and cross-connecting a Power Fail Transfer Unit Connecting an analog (500/2500-type) telephone to a PFTU Ensure that the cable from the appropriate Line card slot has been connected to the telephone. Refer to “Installing the Main Distribution Frame” on page 349. Follow Procedure 107 to connect an analog telephone to a PFTU. Refer to the equipment layout plan to determine where to locate the PFTU. DANGER Always use caution when installing or modifying telephone lines.
PAGE 445
Installing and cross-connecting a Power Fail Transfer Unit Page 445 of 466 Figure 182 Analog Line card cable distribution Lead designation Cable pairs Line Pack Unit 0 Unit 1 Unit 2 Unit 3 Unit 4 Unit 5 Unit 6 Unit 7 Unit 8 Unit 9 Unit 10 Unit 11 Unit 12 Unit 13 Unit 14 Unit 15 Cross connect terminal W-BL BL-W W-O O-W T R T R To 500/2500-type telephone To 500/2500-type telephone W-G G-W W-BR BR-W T R T R To 500/2500-type telephone To 500/2500-type telephone W-S S-W R-BL BL-R T R T R To 500/2500
PAGE 446
Page 446 of 466 Installing and cross-connecting a Power Fail Transfer Unit Procedure 107 Connecting an analog (500/2500-type) telephone to a PFTU 1 Locate the telephone terminations on the cross-connect terminal. 2 Connect one end of the cross-connect wire to the leads of the telephone. 3 Locate the PFTU connections (unit PFTU 1 through PFTU 5) assigned to this telephone at the cross-connect terminal. See Table 60 on page 446.
PAGE 447
Installing and cross-connecting a Power Fail Transfer Unit Page 447 of 466 Table 60 Power Fail Transfer Unit connections (Part 2 of 3) QUA6 J1 Cable Function PFT 2 PFT 3 PFT 4 Pair Color Connects to: 9T 9R R-BR BR-R Telephone 10T 10R R-S S-R Telephone Line card 11T 11R BK-BL BL-BK Central Office Trunk 12T 12R BK-O O-BK Trunk Line card 13T 13R BK-G G-BK Telephone 14T 14R BK-BR BR-BK Telephone Line card 15T 15R BK-S S-BK Central Office Trunk 16T 16R Y-BL BL-Y Trunk Line card 1
PAGE 448
Page 448 of 466 Installing and cross-connecting a Power Fail Transfer Unit Table 60 Power Fail Transfer Unit connections (Part 3 of 3) QUA6 J1 Cable Function PFT 5 Pair Color Connects to: 21T 21R V-BL BL-V Telephone 22T 22R V-O O-V Telephone Line card 23T 23R V-G G-V Central Office Trunk 24T 24R V-BR BR-V Trunk Line card End of Procedure Connecting a trunk to a PFTU Follow Procedure 108 to connect a Trunk to a PFTU.
PAGE 449
Installing and cross-connecting a Power Fail Transfer Unit 6 Page 449 of 466 Repeat for each trunk assigned to the PFTU.
PAGE 450
Page 450 of 466 Installing and cross-connecting a Power Fail Transfer Unit Table 61 Power Fail Transfer Unit connections (Part 2 of 2) QUA6 J1 cable Function P F T 4 P F T 5 Pair Color Connects to: Connects to: 17T 17R Y-O O-Y Telephone — 18T 18R Y-G G-Y Telephone Line card TN assigned to the telephone 19T 19R Y-BR BR-Y Central office trunk — 20T 20R Y-S S-Y Trunk Line card TN assigned to the Trunk 21T 21R V-BL BL-V Telephone — 22T 22R V-O O-V Telephone Line card TN assigned
PAGE 451
456 Page 451 of 466 Installing and cross-connecting an external alarm from a PFTU Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 Installing an alarm using an alarm port assigned in LD 15. . . . . . . . . . 452 Installing an alarm through QUA6 PFTU connections. . . . . . . . . . . . .
PAGE 452
Page 452 of 466 Installing and cross-connecting an external alarm from a PFTU Installing an alarm using an alarm port assigned in LD 15 The system can be equipped with an alarm port that is assigned in software. Connect an analog line to an analog (500/250-type) telephone or another similar type of ringing or alerting device. Follow Procedure 109 to install an alarm using an alarm port assigned in LD 15.
PAGE 453
Installing and cross-connecting an external alarm from a PFTU Page 453 of 466 Installing an alarm through QUA6 PFTU connections A QUA6 PFTU can be used to connect an external alarm through normally open or normally closed contacts of one of its units. The contacts operate under the same conditions as the PFTU and can support the capacities listed in Table 63. Table 63 The AC capacities Maximum AC capacities Switching power 50.0 V A Switching voltage 125.0 V rms Switching current 0.
PAGE 454
Page 454 of 466 Installing and cross-connecting an external alarm from a PFTU Figure 183 Contacts in PFTU PFT 1 on PFTU 8T (R-G) 7T (R-O) Normally connected to a CO trunk 8R (G-R) Normally connected to a trunk line card 7R (O-R) 6T (R-BL) Normally connected to a telephone 5T (W-S) 6R (BL-R) Normally connected to a telephone line card 5R (S-W) Table 64 PFTU connections (Part 1 of 3) Unit P F T 1 NN43041-310 Pair Color Normal mode Failure mode 5T 5R W-S S-W Makes with 6T and 6R Opens 6T a
PAGE 455
Installing and cross-connecting an external alarm from a PFTU Page 455 of 466 Table 64 PFTU connections (Part 2 of 3) Unit P F T 2 P F T 3 P F T 4 Pair Color Normal mode Failure mode 9T 9R R-BR BR-R Makes with 10T and 10R Opens 10T and 10R Makes with 11T and 11R 10T 10R R-S S-R Makes with 9T and 9R Open 11T 11R BK-BL BL-BK Makes with 12T and 12R Opens 12T and 12R Makes with 9T and 9R 12T 12R BK-O O-BK Makes with 11T and 11R Open 13T 13R BK-G G-BK Makes with 14T and 14R Opens 14T
PAGE 456
Page 456 of 466 Installing and cross-connecting an external alarm from a PFTU Table 64 PFTU connections (Part 3 of 3) Unit P F T 5 NN43041-310 Pair Color Normal mode Failure mode 21T 21R V-BL BL-V Makes with 22T and 22R Opens 22T and 22R Makes with 23T and 23R 22T 22R V-O O-V Makes with 21T and 21R Open 23T 23R V-G G-V Makes with 24T and 24R Opens 24T and 24R Makes with 21T and 21R 24T 24R V-BR BR-V Makes with 23T and 23R Open Standard 01.
PAGE 457
462 Page 457 of 466 Basic system telephony configuration Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 Basic system configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 TN assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462 TN assignment. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 458
Page 458 of 466 Basic system telephony configuration See Software Input/Output: Administration (NN43001-611) for information about overlays. Flow charts Figure 184 on page 459 shows the programming overlay (LD) sequence for a new system. The Data-entry-sequence flowchart does not show all possible administration overlays. In some cases, you must move back and forth between overlays to complete the programming.
PAGE 459
Attendant Console LD 12 Digitone Receiver LD 13 Code Resrtriction Block LD 19 Communication Server 1000E Calling Party Name Display LD 95 Digital Telephone LD 11 Speed Call LD 18 Customer Data Block LD 15 Configuration Record 2 LD 97 Configuration Record 1 LD 17 Analog (500/2500-type) Telephone LD 10 Do Not Disturb LD 26 553-A060 Trunk Data Block LD 14 Route Data Block LD 16 Basic system telephony configuration Page 459 of 466 Figure 184 Data-entry-sequence for new systems Installation and C
PAGE 460
NN43041-310 Standard 01.
PAGE 461
CAS Communication Server 1000E ISM TST 553-3001-500 ROA 553-3001-306 553-3001-306 AML CDR Listed DN LDN NET OAS RDR 553-A059 553-3001-306 PPM Password PWD 553-3001-306 553-3001-306 FFC Timers TIM 553-3001-306 553-3001-306 FCR Night Service NIT 553-2751-xxx 553-2631-100 MOP 553-3001-306 CCS Intercept Treatments INT 553-3001-306 553-2671-110 ICP 553-3001-306 HSP 553-2311-316 553-2681-100 AWU 553-3001-306 ANI 553-3001-306 CDB Feature Options FTR Attendant Console ATT D
PAGE 462
Page 462 of 466 Basic system telephony configuration TN assignment Table 65 shows the TN assignments for the MG 1000E.
PAGE 463
466 Page 463 of 466 Configuring IP Peer Networking and managing the Gatekeeper database Contents This section contains information on the following topics: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 Implementation summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 Introduction This chapter provides an outline for configuring IP Peer Networking and managing the Gatekeeper database.
PAGE 464
Page 464 of 466 Configuring IP Peer Networking and managing the Gatekeeper database You must configure the following data when setting up a CS 1000E IP network: 1 a route information b network management information (for example, Access Restrictions) c bandwidth zone d Signaling Server host name for the route e protocol identifier f associated Node ID 2 Configure the Virtual Trunks using Element Manager or the Command Line Interface (LD 14).
PAGE 465
Configuring IP Peer Networking and managing the Gatekeeper database 5 Page 465 of 466 Configure the Gatekeeper database to provide a central database of addresses that are required to route calls across the network, using the Gatekeeper web pages in Element Manager. a Log in to the Gatekeeper web pages in Element Manager. b Verify that the Gatekeeper is the Primary Gatekeeper and is active. c Configure the System Wide Settings. d Create the CDP domains. e Add the RAS and non-RAS endpoints.
PAGE 466
Page 466 of 466 NN43041-310 Configuring IP Peer Networking and managing the Gatekeeper database Standard 01.
PAGE 467
PAGE 468
Family Product Manual Contacts Copyright FCC notice Trademarks Document number Product release Document release Date Publish Nortel Communication Server 1000 Communication Server 1000E Installation and Commissioning Copyright © 2008 Nortel Networks. All rights reserved. The information in this document is subject to change without notice.