MODEL: NSD1 0000 PACKING DIAGRAM LOWER FOUNTAIN BODY (2) WASHERS AND (4) SCREWS�----. t------AASIN, (2) WASHERS AND (2) SCREWS.
You should have received the following parts in the package. Please ensure that all parts are accounted for.
Care and Instruction Manual
NSD10000 ASSEMBLY INSTRUCTIONS Please reference the separate parts list and ensure that all pieces are included in the package prior to assembly. SUGGESTED TOOLS NOT SUPPLIED PHILLIPS SCREWDRIVER More than one person may be required to complete the assembly of this product. To protect the finish, place all parts on a soft surface when unpacking. We recommend using this fountain against a wall. When assembling ensure that all parts are firmly tightened.
NSD10000 ASSEMBLY INSTRUCTIONS Unscrew parts 2 x M and 2 x L from lower fountain body (C). Use 2 x L and 2 x M to secure plate (D) to lower fountain body (C). C D L M Loosen parts 2 x N in top of fountain body (C). Insert pins into holes, and then tighten parts 2 x N.
NSD10000 ASSEMBLY INSTRUCTIONS Feed rubber hose through hole and attach pump (G) to rubber hose. Run pump cord through notch in back of basin (E), use 2 x L and 2 x M to secure the fountain body assembly (C) to basin (E). C M L G Rubber hose G Feed light cord (I) through plastic tube.
NSD10000 ASSEMBLY INSTRUCTIONS Insert light (I) into light clip. Place lid (A) onto upper fountain body (B). I Light clip A B A FINAL STEPS Fill the basin (E) with 2.5 gallons of distilled water, between the fill lines. Place pump access door (F) into basin (E). Place decorative river stones (J) onto basin (E). Connect the light connectors (H) and (I) and screw the cap tightly. 7 Plug light transformer (H) and pump (G) into outlets and turn light on at switch. Use shims (K) to level the fountain.
NSD10000 ASSEMBLY INSTRUCTIONS PUMP SAFETY & TROUBLESHOOTING To clean the pump Unplug the pump from the electrical outlet. Use a small soft brush or place it under a water stream to remove debris. To keep water clean Periodically change water to prevent algae buildup. Tube Rotor/Impeller Impeller cover Back cover Pump housing Suction cup Front cover Flow regulator If the pump fails to run: • Check circuit breaker, or try a different outlet. • Check tubing for kinks and obstructions.
NSD10000 ASSEMBLY INSTRUCTIONS WATER FEATURE WARNINGS & TROUBLESHOOTING • Splashing may occur when the fountain is first turned on, protect surrounding surfaces as needed. Do not place the water feature on or near any surface that can be damaged by water. • Distilled water is recommended to reduce mineral deposits, bacteria build up and algae that may damage the water feature basin and pump. • To reduce the risk of electrical shock, always disconnect the power supply before working with the water feature.
NSD10000 ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS What should I consider when selecting a water feature? In addition to your personal style tastes, be sure you have an area for your water feature that can be safely exposed to water, as splashing can occur. Also take into consideration what a water feature can add to your environment: the sound of flowing water or decorative lights.
NSD10000 ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS CONTINUED How much water do I need to keep in the water feature? Where possible in our water features, we have included fill lines to help you visualize the water level required for proper function. If your water feature does not include fill lines, please check the instruction manual for water capacity.
NSD10000 ASSEMBLY INSTRUCTIONS FREQUENTLY ASKED QUESTIONS CONTINUED How do I change my pump speed? Depending on the type of pump, you will need to either move the slider or turn the knob. Flow control valve Maximum Minimum How do I clean my pump? 1. Disconnect the power supply and then remove pump cover/filter. 2. Gently pull impeller/rotor assembly out of the pump housing 3. Rinse the impeller/rotor assembly and the cavity with clean water. 4.