M296022B.1 MODEL NUMBER: 296022 SERIAL NUMBER: _____________ Owner’s Manual Instructions for Assembly and Testing Tow package for a Stump and Root Grinder (Used on NorthStar Stump Grinder 296020) WARNING READ and UNDERSTAND this manual completely before using this Tow Package. All operators of this equipment must read and completely understand all safety information, operating instructions. Improper use of the tow package could result in serious injury to the operator or nearby persons.
Hazard Signal Word Definitions 2
Table of Contents Safety Label Location ............................................................................................................................ 4 Machine Components Identification ...................................................................................................... 5 Towing Instructions................................................................................................................................ 6 Specifications ........................................
Safety Decal Locations To order replacement safety label part #785623, call NorthStar Product Support at 1-800-270-0810. WARNING ALWAYS make sure safety labels are in place and in good condition. If a safety label is missing or not legible, order new labels.
Machine Components Identification 1.) 2.) 3.) 4.) 5.) Tow Bar. Connects the Stump Grinder to the tow vehicle. 2” Coupler. Allows the trailer unit to be hooked up to a 2” ball hitch. Safety Cables. Secures trailer to vehicle in case of accidental disconnection of ball and coupler. Tow Bar Socket. Connects the Tow Bar to the Stump Grinder Hitch Pin.
Towing Instructions IMPORTANT! See Assembly Instructions section of this manual to assemble the Stump Grinder Tow Package. Now that you have installed the Stump Grinder Tow Package, there is some important safety information you need to know with regard to vehicle handling with the Stump Grinder attached. Step One. Inspect/Repair If the Stump Grinder has been towed previously, it must be prepared BEFORE EACH SUBSEQUENT USE.
Towing Instructions and licensing). Be sure receiver on towing vehicle is bolted tightly. Towing vehicle capability must be matched to trailer weight and type of hitch arrangement 1. Attach Stump Grinder coupler to a class 2 or higher hitch with 2” ball (only). 2. Adjust coupler to ball by raising locking lever and turning lock nut with fingers. 3. Proper adjustment is obtained when coupler is as tight as possible on ball and locking lever can still be opened and closed. 4.
Specifications Maximum Towing Speed……………. Coupler Size…………………………. Overall Dimensions (boxed)…….…... Weight (shipping)………………….… 45 MPH 2” Ball 39.5”L x 7”W x 4.5 ”H 20 lbs. The manufacturer reserves the right to make improvements in design and/or changes in specifications at any time without incurring any obligation to install them on units previously sold.
Parts Breakdown – Exploded View Item 1 2 3 4 5 Part # 82024 785491 785490 82291 38587 Description 3/8” x 1-1/4” Bolt Tow socket Tow bar 1/2” Flange nut 2” Ball coupler Qty 4 1 1 2 1 Item 6 7 8 9 10 9 Part # 82118 82290 30312 37459 792482 Description 1/2” x 3” Bolt 3/8” Lock nut Cotter pin Hitch pin Safety cable Qty 2 4 1 1 2
Safety Instructions WARNING Carefully read and make sure you understand the following safety information before towing the Stump Grinder. Improper use or maintenance of the Stump Grinder can result in serious injury to the operator or bystanders. Safety in Moving and Towing the Stump Grinder WARNING The Stump Grinder is very heavy. It can crush and cause serious injury if it rolls out of control or tips over. Follow the instructions below for safely moving and towing the Stump Grinder.
Unpacking Closely inspect all contents in the shipping carton. • If you have missing or damaged components: Contact NorthStar Product Support at 1-800-270-0810.
Assembly Instructions Step 1 ▪ Attach Tow Bar Socket to Stump Grinder Using (4) 3/8” x 1-1/4” Bolts and (4) 3/8” Class G Locking Nuts. ▪ Tighten Bolts to 19 lb-ft torque. 3/8” bolt Tow bar socket 3/8” lock nut Fig 03534 Step 2 Tow Bar ▪ Attach coupler to Tow Bar by using (2) 1/2” x 3” bolts and (2) 1/2” Class G Flange Nuts. ▪ Tighten Bolts to a 90 lb-ft torque.
Assembly Instructions cont’d Step 4 Tow Bar Socket ▪ Slide the Tow Bar into the Tow Bar Socket and secure with Hitch Pin. ▪ Lock Hitch Pin into position using cotter pin.
This page has intentionally been left blank.
Limited Warranty Policy Dear Valued Customer: The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance.
WARNING: This product can expose you to soots, tars, and mineral oils (untreated and mildly treated oils and used engine oils), which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. ® Manufactured by Northern Tool + Equipment Co., 2800 SouthCross Drive West P.O.
