Generator Wheel Kit Item # 165620, 165621 For use on: 165601, 165603, 165604, 165605, 165606, 165607 M165620E.4 OWNER’S MANUAL 165621 165620 Ref. Part # Description 1 2 4 5 6 7 82021 82301 791834 785398 788813 305200 82018 785395 8 82019 5/16” washer (reuse from gen.) Star washer (reuse from gen.) 165620 Axle 165621 Wheel Wheel retainer 5/16” x 2” bolt (reuse from gen.) Axle mount 165620 165620 5/16” flange nut 165621 3 9 10 11 12 Used on 82019 5/16” flange nut (reuse from gen.
STEP 1 • Open hardware bag and separate the components.
STEP 2 • Secure generator on blocks at least 7” tall. Make sure the space between the holes for the axle is not obstructed. STEP 3a Item # 165620 only 1. Remove 5/16” x 2” bolt, star washer, flat washer and 5/16” nut from generator base. 2. Attach axle mount to frame reusing 5/16” x 2” bolt, star washer, 5/16” washer, in addition to 5/16” x 3/4” bolt and 5/16” nuts as shown. 3. Attach second axle mount on to frame, repeating axle to frame fastener installation. 4.
STEP 3b Item 165621 only 1. Install one wheel retainer onto axle so it is flush with the axle end. Tighten with a 5/32” hex driver. 2. Slide one wheel onto the axle, so that the offset hub is opposite the wheel retainer. 3. Slide the axle through the holes on both sides of the base. 4. Slide the second wheel on to the axle. Wheel offset hub should face the generator. 5. Install other wheel retainer onto axle so it is flush with the axle end. Tighten with a 5/32” hex driver.
STEP 4b Item 165621 only Serial Number Decal 1. Attach the large rubber foot to the leg using 5/16” x 1-1/2” bolt and 5/16” flange nut. If installing a 165621 on a 165605, 165606, 165607 Rev V or later, place the spacer between the rubber foot and the leg. Revision letter can be found on the serial number decal refer to the figure to the right for its location. 2. Remove 5/16” x 2” bolt, star washer, 5/16” washer and 5/16” nut from generator base. 3.
STEP 5 1. Install grip onto handle. 2. Attach small bumper to handle with 1/4” x 3/4” self-tapper. 3. Insert (1) 3/8” x 2-1/2” bolt through (1) flat washer and through one end of lanyard as shown. Attach 3/8” cotterless pin to other end of lanyard. 4. Install handle to generator using 3/8” x 2-1/2” bolt, (4) flat washers and (1) 3/8” nyloc nut until washers press against tube walls. 5. Repeat steps for other handle. 6. Insert cotterless pin through bottom hole of arm so handle doesn’t fold up while in use.
Dear Valued Customer: The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance.
WARNING: This product can expose you to Naphthalene, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. Manufactured by Northern Tool + Equipment Co., Ltd. Burnsville, MN 55306 NorthernTool.