Owner's Manual

ManualsBrandsNOTIFIER ManualsControl DisplayNOTIFIER NCD Network Control Display

NOTI•FIRE•NET™ is a trademark of, and NOTIFIER® and

ONYX® are registered trademarks of Honeywell Interna-

tional Inc.

Unauthorized use of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

Country of Origin: USA

NOTIFIER

12 Clintonville Road

Northford, CT 06472

203.484.7161

www.notifier.com

FUNCTION TOUCHPOINTS

•Menu

•Login

• Acknowledge

• Signal Silence

• System Reset

Ack (Acknowledge) Tap this touchpoint to acknowledge off all

active events.

Silence (Signal Silence) Tap this touchpoint to turn off all control

modules, notification appliance circuits, and panel output circuits

that have been programmed as Silenceable.

Reset (System Reset) Tap this touchpoint to clear all latched

alarms and other events and clear event indicators.

MENU FUNCTION TOUCHPOINTS

Menu function touchpoint are accessible though the menu dialogs.

• ABOUT – tap this touchpoint to view current firmware and hard-

ware revision numbers.

• DISPLAY – tap this touchpoint to adjust display settings.

• LAMP TEST – tap this touchpoint to test display pixels, LED indi-

cators and piezo.

Specifications

Temperature and humidity ranges: This system meets NFPA

requirements for operation at 0°C to 49°C (32°F to 120°F); and at a

relative humidity (non-condensing) of 85% at 30°C (86°F) per

NFPA. However, the useful life of the system’s standby batteries

and the electronic components may be adversely affected by

extreme temperature ranges and humidity. Therefore, it is recom-

mended that this system and all peripherals be installed in an envi-

ronment with a nominal room temperature of 15°C to 27°C (60°F to

80°F). Product weight is 3 lbs (1.36 kilograms).

ELECTRICAL REQUIREMENTS

The NCD may be powered from any UL Listed non-resettable 24

VDC source from a NOTIFIER compatible fire panel (see panel

data sheets). Power source: 1) AMPS-24 (120 VAC, 50/60 Hz) or

AMPS-24E (240 VAC, 50/60 Hz) power supply; 2) the NFS2-640

and NFS-320 on-board power supply; or 3) a supervised +24 VDC

power supply that is UL-listed for fire protective service. The cur-

rent consumption of the NCD is 360 mA.

Product Line Information

NCD: Network Control Display. Requires a network communica-

tions module for networking. In direct connect applications, the

NCM is not required.

NCM-W, NCM-F: Standard Network Communications Modules.

Wire and multi-mode fiber versions available. See DN-6861.

HS-NCM-W/MF/SF/WMF/WSF/MFSF: High-speed network com-

munications modules. Wire, single-mode fiber, multi-mode fiber,

and media conversion models are available. See DN-60454.

ABS-TD: Ten inch display annunciator Backbox, Surface, black.

Mounts NCD and one network control module.

CAB-4 Series Enclosure: Available in four sizes, “AA” through

“D”. Backbox and door ordered separately; requires BP2-4 battery

plate. See DN-6857.

DP-GDIS2: Graphic Annunciator Dress Plate. Dress plate is used

when the 10" graphic display is mounted in CAB-4 Series cabinet,

except top row.

DP-GDIS1: Graphic Annunciator Dress Plate. Dress plate is used

when the 10" graphic display is mounted in the top row of a CAB-4

Series cabinet.

Agency Listings and Approvals

These listings and approvals apply to the NCD. In some cases,

certain modules or applications may not be listed by certain

approval agencies, or listing may be in process. Consult factory for

latest listing status.

UL Listed: S635.

CSFM: 7300-0028:0507.

FM Approved.

firealarmresources.com