NF/NM -4/8 Installatiehandleiding & Gebruikershandleiding Version V0203
INHOUD 4 1 INLEIDING 5 2 Transportschade 5 3 Montage 6 3.1 Verwijderen printplaten 6 3.2 Monteren van de behuizing 7 4 Bedrading 8 5 Elementen 8 6 Opstarten van de centrale 9 6.1 Eerste stap 9 6.2 Tweede stap 9 6.3 Derde stap 10 6.4 Vierde stap 10 7 Zone Bedrading 7.
15 15 15 Vervolg knoppen en indicatoren 16 15 Vervolg knoppen en indicatoren 17 15.1 Sleutel en druktoetsen 18 15.2 Interne zoemer 19 16 De alarmmelding 20 17 Storings melding 21 Tabel localiseren van problemen 22 Isoleer en test functies 23 18 19 Inhoud Knoppen en indicatoren 18.1 Procedure 23 18.2 Kiezen van in -of uitgangen 24 18.3 Wijzigen toestand 25 Software opties 28 19.1 Instellen van DIP Schakelaars 28 19.2 MCP zones met onmiddellijke actie 30 19.
Beperkingen van het systeem Een automatisch brandmeld systeem bestaat meestal uit rook en warmte melders, handmelders, waarschuwings elementen.., om op die manier een vroegtijdige waarschuwing te geven bij het ontwikkelen van een brand. Het systeem kan niet verantwoordelijk gesteld worden voor het verlies van goederen of levens veroorzaakt door een brand.
NF/NM -4/8 Installatie en gebruikers handleiding 1 Inleiding In deze handleiding wordt het installeren, configureren en het gebruik van de centrale beschreven. Het betreft hier een compact 8 zone brandmeld paneel dat volledig ontworpen werd volgens de geldende Europese normen (EN54 deel 2 en 4) Het systeem is voorzien van een netspanningsvoeding en moet ook voorzien worden van een back-up voeding door middel van 2 lood-zuur akku’s. De grootte van de akku’s hangt af van het type en aantal verbruikers.
NF/NM -4/8 Installatie en gebruikers handleiding 3 MONTAGE 3.1 Verwijderen van de printplaten Statisch gevoelige componenten! Gebruik antistatisch armbandje. Wij raden aan de elektronische printplaten te verwijderen tijdens het plaatsen van de kast tegen de muur. Dit heeft meerdere voordelen. >De elektronica kan niet beschadigd worden door de boormachine, boorresten of kabelresten tijdens het ontmantelen. >Het inbrengen van kabels en het plaatsen van wartels is veel eenvoudiger.
NF/NM -4/8 Installatie en gebruikers handleiding 3.2 Monteren van de behuizing Op bijgaande tekening vindt U de afmetingen van de kast samen met de boorgaten. 1 Gebruik de lege behuizing om de boorgaten aan te geven op de wand. Nooit de kast als boormal gebruiken ! 2 Boor de gaatjes en gebruik de hiervoor bestemde pluggen. 3 Wij raden aan de voorgeponste wartelgaten door te kloppen vooraleer de kast gemonteerd wordt zodat de bevestigingsschroeven niet losgeklopt worden.
NF/NM -4/8 Installatie en gebruikers handleiding 4 Bedrading Kabels moeten in overeenstemming met de lokaal geldende wetten geinstalleerd worden. (NBN-S21-100 voor Belgie en Nen 2535 voor Nederland) Netspanning : Wat betreft de 220VAC netspanning moet ervoor gezorgd worden dat er een kring gebruikt wordt die enkel voor dit doel bestemd is. Verder moet deze kring van een aparte dubbelpolige schakelaar en zekering voorzien zijn.
NF/NM -4/8 Installatie en gebruikers handleiding 6 Opstarten van de centrale Het is aan te raden de NF 8 centrale op te starten en te testen vooraleer de draden aan te sluiten. Dit gebeurt best als volgt : 6.1 Eerste stap Sluit al de zones af met de bijgeleverde 4K7 eindelus weerstand. Sluit ook de sireneuitgang (acustic) af met een 4K7 weerstand. Plaats een 1K/1W weerstand over de transmissieuitgang (UE+ and UE-) alsook een 3K3 weerstand over de ingang (SL+ and SL-).
NF/NM -4/8 Installatie en gebruikers handleiding 6.3 Derde stap Aansluiten van de netspanning WAARSCHUWING HOOGSPANNING ! LET OP : DEAARDE MOET AANGESLOTEN WORDEN OP DE CENTRALE GEBRUIK BEST EEN KRIMP_TOOL OM EEN AANSLUITRINGETJE TE BEVESTIGEN De fase en de nulleider moeten op de print aangesloten worden. Zorg ervoor dat de kabelmantel zo kor t mogelijk ontbloot wordt tegen het aansluitblok. De aarde moet goed aangesloten worden volgens de tekening op pagina 14 en 23.
NF/NM -4/8 Installatie en gebruikers handleiding 7 Zone bedrading De aansluiting van de draden moet correct afgewerkt worden volgens onderstaand systeem. 7.1 Procedure Verwijder de 4K7 weerstand op de centrale. Sluit nu de zonedraden aan. Vergeet niet eerst te meten of de 4K7 weerstand aan het einde van de lus zit. Er moet altijd een 4K7 weerstand in het laatste element van de lijn gemonteerd worden. De centrale moet terug in rust komen nadat de zonedraden werden vastgemaakt.
NF/NM -4/8 Installatie en gebruikers handleiding 680R 3K3 S t u r i n g Blussing 10 Uitgang blussing Het is mogelijk een speciaal bluspaneel aan te sturen met deze uitgang. De uitgang L+ L- kan met een enkele of dubbele zone geactiveerd worden. Dit wordt bepaald door DIP switch S3 sw8 (zie deel 19). Als de supervisie ingang niet gebruikt wordt, moeten we deze afsluiten met een 3K3 weerstand op SL+ and SLklemmen.
NF/NM -4/8 Installatie en gebruikers handleiding 12 Testen Verzeker U ervan dat het verwijderen van een detector , of een lus alsook het kortsluiten van de lus aangegeven worden. Controleer al de breekglaasjes en detectoren door ze in alarm te brengen met de testsleutel. Controleer eveneens of de sirenes aangestuurd worden volgens de instellingen. 13 Sirene als spanningsvrij kontact De sireneuitgang kan als spanningsloos kontakt gebruikt worden. Maak een keuze tussen N/O of N/G kontakt via jumpers.
NF/NM -4/8 Installatie en gebruikers handleiding Installatie Bedradings overzicht Fuses: F1 - Netspanning T 1AH 250V F3 - Auxiliaire 24VDC uitgangen 0.5A F4 - FBF 0.5A F5 - Sirene uitgang 1A F6 - Transmissie uitgang 0.5A F7 - Batterijlader 2A anti surge, HRC, keramisch.
NF/NM -4/8 Installatie en gebruikers handleiding Gebruikers instructies KNOPPEN EN INDICATOREN 15 Version V0203
NF/NM -4/8 Installatie en gebruikers handleiding 1 5 KNOPPEN EN INDICATOREN BRAND - 1 rode algemeen brand indicator. Dez licht continu op en blijft branden tot het paneel gereset wordt. STORING - 1 gele indicator. deze zal pulseren 2 seconden AAN en 0.5seconden UIT als de storing van een zone afkomstig is. Gebruikers instructies ZONE BRAND - 1 rode led per zone. deze zal knipperen 0.5 seconden AAN, 0.5 seconden UIT als de bijhorende zone in alarm is.
NF/NM -4/8 Installatie en gebruikers handleiding BUITEN DIENST - Gele led die continu oplicht als er een of meer elementen buiten dienst staan. In CONFIGURATIE Mode kunnen we samen met de IN TEST indicator zien wat de toestand van een zone is. IN TEST - Deze led zal continu branden als er een of meer zones in test staan. In CONFIGURATIE Mode kunnen we samen met de BUITEN DIENST indicator zien wat de toestand van een zone is. STORING BLUSSING- 1 gele indicator.
NF/NM -4/8 Installatie en gebruikers handleiding 15.1 DE SLEUTEL & DRUKTOETSEN SLEUTELSCHAKELAAR De sleutel kan op drie posities geplaatst worden A A Normaal - In deze toestand heeft de sleutel geen functie, het paneel is in rust. Dit is ook de toestand waarin de sleutel verwijderd kan worden.
NF/NM -4/8 Installatie en gebruikers handleiding DRUKTOETSEN Voor het bedienen van de centrale hebben we de beschikking over volgende druktoetsen : 2 RESET - Deze toets is enkel beschikbaar als de sleutel in de middenste positie staat. Door op deze toets te drukken wordt het paneel terug in zijn normale toestand gebracht na een alarm of een storing. Indien de oorzaak nog aanwezig is zullen de meldingen terug weergegeven worden.
NF/NM -4/8 Installatie en gebruikers handleiding 16 De ALARMMELDING Normaal - In normale toestand mag er enkel een indiactie van “VOEDING OK” oplichten. Er is verder ook geen akoestische indicatie ALARM - Als er een alarm optreedt, dan wordt de rode led ALARM (continu) samen met de rode led van de betreffende zone (pulserend) aangestuurd. De transmissieuitgang, sirenes en eventueel een blussturing worden bij een alarm geactiveerd, tenzij ze buiten dienst stonden.
NF/NM -4/8 Installatie en gebruikers handleiding 17 De STORING Als er een storing ontstaat in het systeem, dan worden de led “STORING” en de zoemer pulserend aangestuurd. De zoemer kan gestopt en de melding geaccepteerd worden door op “BUZZER UIT” te drukken. Afhankelijk van de storing kan een andere led oplichten zoals hieronder beschreven. Zone storing/test/buit.dnst - De gele led bij de zone kan oplichten als er een open kring of kortsluiting op de zonebedrading wordt waargenomen.
NF/NM -4/8 Installatie en gebruikers handleiding LOCALISEREN VAN PROBLEMEN Gebruikers instructies Indicatie Mogelijke oorzaak Actie Geen indicatie op paneel, geen buzzer.
NF/NM -4/8 Installatie en gebruikers handleiding 18 ISOLEER -EN TEST FUNCTIES Er zijn mogelijkheden ingebouwd om zones en uitgangen te testen of buiten dienst te stellen. Iedere individuele zone kan buiten dienst of in test geplaatst worden. De uitgangen transmissie, sirene en blussing kunnen enkel buiten dienst gesteld worden. Er wordt verwezen naar deze isoleer en test functies als de “Setup Mode”.
NF/NM -4/8 Installatie en gebruikers handleiding 18.2 Keuze van IN of UITGANG Na uitvoeren van voorgaande procedure komen we in de setup mode. Dit wordt dus aangegeven door het snel knipperen van de led “TRANSMISSIE UIT/STORING”. Met de STAP toets kunnen we nu deze cursor (=knipp.led) verder bewegen naar de zone of functie die we wensen te selecteren. De led beweegt van “TRANSMISSIE UIT” naar “TX UIT” via “FOUTRELAIS UIT” naar de gele led bij iedere zone.
NF/NM -4/8 Installatie en gebruikers handleiding 18.3 Wijzigen toestand Selecteer zoals hiervoor beschreven een uitgang of zone. De toestand van deze uitgang of zone kan nu via de toets TOESTAND gewijzigd worden. Transmissie, blussturing en foutrelais : Isoleer en test functies Deze drie uitgangen kunnen we buiten dienst zetten. Een testfunctie is hier niet mogelijk. Indien een van beide uitgangen buiten dienst staat zal de led “BUITEN DIENST” oplichten samen met de betreffende in- of uitgang.
NF/NM -4/8 Installatie en gebruikers handleiding Zones: Zones hebben 3 verschillende toestanden, nl. Normaal, Buiten dienst en In Test. Dit wordt aangegeven door de led’s BUITEN DIENST en IN TEST Door op de knop TOESTAND te drukken kunnen we volgende functies selecteren : Normaal De led’s BUITEN DIENST en IN TEST zijn beide gedoofd Buit.dnst De BUITEN DIENST led brandt continu.
NF/NM -4/8 Installatie en gebruikers handleiding Door het gebruik van deze functie kan dus eender welke zone of uitgang in de juiste toestand gebracht worden. Belangrijke Nota : Het verwijderen van alle voedingsbronnen en het opnieuw opstarten zal ervoor zorgen dat alles terug normaal staat na de koude start. Terug uitschakelen van Buiten DNST of TEST STEP DISABLE OUTPUTS/ ENABLE CONTROLS STATE Het systeem kan terug in normale toestand gebracht worden via volgende acties : 1.
NF/NM -4/8 Installatie en gebruikers handleiding 19 SOFTWARE OPTIES Een aantal software opties kunnen geselecteerd worden door middel van micro schakelaartjes. Deze zijn terug te vinden op de processorprint zoals aangegeven op bijgaande figuur. De uitleg van ieder schakelaartje vinden we terug in de tabel achteraan in deze handleiding. Enkele opties worden hardwarematig ingesteld via jumpers 1. Keuze tussen resetbare of continue 24VDC voeding op AUX1 uitgang. 2. Aardlek bewaking aan of uit. 3.
BLOK Switch Naam Beschrijving 8 Transmissieuitgang bij dubbele zone OFF : Geen twee-zone afhankelijkheid voor transmissie uitgang UE ON : Wel tweegroepen afhankelijkheid voor TUransmissieuitgang UE NOTA : De MCP zones sturen altijd direkt aan 7 Vertraging netspanning storing OFF : Storing netspanning stuurt het storingsrelais na 100s aan ON : Storing netspanning stuurt het storingsrelais na 30 min aan 6 Dag/nacht mode OFF : Geen dag-nacht schakeling mogelijk ON : Dag-nacht functies zijn beschikb
NF/NM -4/8 Installatie en gebruikers handleiding 19.2 De MCP zone met onmiddellijke actie De zones 1 tot 4 kunnen gebruikt worden als MCP (of directe) zone. Dit wil zeggen dat deze zone geen rekening houdt met ingestelde vertragingen of dubbeltoets systemen. Zij heeft altijd een onmiddellijke actie tot gevolg. Een MCP zone stuurt dus de uitgangen altijd onmiddellijk aan. 19.3 Contact onder frontplaat Een contact onder de frontplaat bewaakt of deze geplaatst is.
NF/NM -4/8 Installatie en gebruikers handleiding 20 Berekening batterijen Algemene Data Totale Stroom Maximum aantal sirenekringen 1.9A 1 Maximum stroom in alarm Maximum grootte batterijen 1.5A 12Ah Normaal verbruik Volledig 8 zone paneel met maximum aantal melders Stroom Totaal 0.120 0.120 1 Andere verbruikers ? Totale stroom in rust (L1) * Bevat ook FBF, TX en blusuitgang Totaal in alarm (A) Stroom in Alarm Stroom Totaal 8 zones in alarm plus uitgangen 1 0.580 0.
NF/NM -4/8 Installatie en gebruikers handleiding 21 Technische gegevens Netspanning .............................. 230 ± 15% V AC 50/60 Hz Voldoet aan VDE 0833 Part 2: 1992 at 230V nominal. Ingangs stroom ......................... 0.75A Systeem spanning ...................... 24V DC Nominal (20-28 VDC) Sleutelschakelaar ..................... 3 Posities : (i) NORMAAL (ii) Blokkeer blussing en transmissie + druktoetsen beschikbaar Technische gegevens (iii) Sirenes AAN/UIT/Buit.dnst Toetsen ................
NF/NM -4/8 Installatie en gebruikers handleiding Sirenekring ............................... Spanning 20 to 28 V DC MAX Stroom 1.0A Afsluitweerstand 4K7 Zekeringen ................................ 220VAC 1A(20mm A/S ceramic) Sirene: 1A (20mm A/S) 24VDC (2 off): 0.5A (20mm A/S) Transmissie uitgang : 0.5A (20mm A/S) Batterij: 2A (20mm A/S HRC ceramic) FBF Uitgang : 0.5A (20mm A/S) Algemeen ALARM relais ............ Spanningsvrij kont 1.0A / 30V DC Algemene STORING relais ......... Spanningsvrij kont 1.
NOTIFIER BENELUX HEAD OFFICE BRANCH OFFICE Avenue de l’Expansion, 16D B-4432, ALLEUR Belgium Tel: +32 42 470 300 Fax: +32 42 470 220 Pompmolenlaan, 43A NL-3447 GK, WOERDEN The Netherlands Tel: +31 348 434 995 Fax: +31 348 434 962