NF30/50 Gebruikershandleiding v0903
NF30/50 Reeks - Gebruikershandleiding Inhoud Inleiding 1 1.1 Begeleidende Documenten 1 1.2 De NF30/50 Panelen 1 1.2.1 Type elementen afkortingen 2 Reinigen 2 1.3 2 Bediening en indicatoren 3 2.1 Bediening 3 2.2 Indicatoren 4 3 Automatische alarmen - Wat doen 3.1 3.2 3.3 4 Brand 5 3.1.1 Brand in vertraagde toestand 7 Storing 8 3.2.1 Storing Voeding 9 Gebouw meldingen Bedieningsacties op de centrale 4.1 5 10 11 Inleiding 11 4.1.1 Liquid Crystal Display 11 4.1.
NF30/50 Reeks - Gebruikershandleiding 4.9 IN / BUITEN DIENST - Gebruikersoptie 25 4.9.1 Zone - Gebruikersoptie 26 4.9.2 Uitgangen - Gebruikersoptie 28 4.9.3 Dag mode - Gebruikersoptie 29 4.9.4 Vertragingen - Gebruikersoptie 30 4.10 Klok - Gebruikersoptie 4.10.1 Tijd - Gebruikersoptie 32 4.10.2 Datum - Gebruikersoptie 33 Inhoud 4.11 DISPLAY MODE - Gebruikersoptie v0903 31 34 4.11.1 Log - Gebruikersoptie 35 4.11.2 Elementen - Gebruikersoptie 36 4.11.
NF30/50 Reeks - Gebruikershandleiding Reeks Paneel NF30/50Inhoud NF30/50 Reeks iii v0903
Inhoud NF30/50 Reeks - Gebruikershandleiding v0903 iv
NF 30/50 Reeks - Gebruikershandleiding 1 Inleiding Dit boek bevat gebruikersinstructies voor de NF30 en NF50 serie intelligente brandmeldcentrales. Verschillen tussen de NF30 en NF50 worden in Bijlage 3 weergegeven. We gaan ervan uit dat de gebruikers van deze handleiding werken met een paneel dat reeds werd geïnstalleerd en geconfigureerd op een manier die geschikt is voor de betreffende regio. 1.
NF 30/50 Reeks - Gebruikershandleiding 1.2.1 Type elementen afkortingen Doorheen dit boek verwijst het paneel soms naar een element door gebruik te maken van een afkorting. In onderstaande tabel staan de afkor tingen en de beschrijvingen van de elementen opgesomt.
NF30/50 Reeks - Gebruikershandleiding 2 Bediening en indicatoren De bediening en weergave op het paneel van de NF30/ 50-reeks is bedoeld om het totale systeem te bedienen en de status ervan weer te geven. Het paneel is voorzien van 4 functietoetsen, 12 numerieke/cursortoetsen en 32 zone led’s, 2 “BRAND” LED’s en 14 LED’s waarmee de status van het systeem wordt weergegeven. 2.
NF30/50 Reeks - Gebruikershandleiding 2.2 Indicatoren De statusindicatoren kunnen we groeperen in 3 groepen: a. Zone Status indicatie led’s. b. Paneel/Systeem indicatie led’s. c. Audio/visuele indicatoren. Zone Status indicatie led’s • BRAND - led’s geven de zone(s) in kwestie aan. • STORING/TEST BUITEN DIENST - led’s geven de zone(s) in kwestie aan. Paneel/Systeem indicatie led’s Bediening en indicatoren • BRAND - led’s geven aan dat er brand is.
NF30/50 Reeks - Gebruikershandleiding 3 Automatische alarmen - Wat doen Voor deze beschrijving gaan we ervan uit dat het systeem zich in de Toestand: NORMAAL bevindt. De gebruiker moet een pascode niv. 2/3 ingeven of de sleutelschakelaar omdraaien om de toetsen van het paneel te activeren. Er kan maar één alarm conditie op het LCD scherm weergegeven worden. Als brand alarmen, storingen en/ of gebouw meldingen op het zelfde moment aanwezig zijn, worden ze in deze volgorde getoond: b. Storingen. c.
NF30/50 Reeks - Gebruikershandleiding Aanbevolen gebruikers acties: Automatische alarmen - Wat doen 1 Nota: Van de hieronder beschreven acties is enkel de STOP ZOEMER toets beschikbaar op gebruikersniveau 1. De andere toetsen: RESET, STOP/HERSTART SIRENES en TRANSMISSIE AAN/UIT mogen volgens de EN54:Part 2 enkel bereikbaar zijn via de sleutelschakelaar of een pascode niv. 2. 1 Druk op de ‘STOP ZOEMER’ - toets om de interne zoemer te stoppen.
NF30/50 Reeks - Gebruikershandleiding 3.1.1 Brand in vertraagde toestand Twee geconfigureerde vertragingstijden (Eerste en verlengde), zullen de activering van de overeenstemmende uitgangen vertragen voor max. 10 minuten. Deze tijden zijn ingesteld tijdens de programmatie door de installateur. Nota: Indien er geen vertragingen ingesteld zijn zullen de uitgangen onmiddellijk aangestuurd worden.
NF30/50 Reeks - Gebruikershandleiding 3.2 Storing Automatische systeem acties: Indien het systeem een storing detecteert, voert de centrale altijd de volgende acties uit: a. De interne zoemer activeren (2 sec. aan, 1 sec. uit). b. De betreffende storings led’s zullen oplichten, inclusief de betreffende ‘STORING/TEST BUITEN DIENST’ zone - led’s indien van toepassing. Automatische alarmen - Wat doen c. Activeren van de geprogrammeerde modules, die met de desbetreffende storingsmelding zijn geassocieerd.
NF30/50 Reeks - Gebruikershandleiding 2 Indien een service telefoonnummer ingegeven is tijdens programmatie zal het LCD tussen de storings en dit nummer scrollen na het drukken op ‘STOP ZOEMER’. A B C D STORING 01 / 03 Service Contact ***** ****** E 14:55 3 Druk ‘RESET’ wanneer de storing opgelost is, om het systeem naar Toestand: NORMAAL terug te brengen. Toestand: NORMAAL Din 01/07/2003 14:55:00 3.2.
NF30/50 Reeks - Gebruikershandleiding 3.3 Gebouw meldingen Een ‘Gebouw’ melding wordt weergegeven indien het systeem een niet-brand melding van een AUX ontvangt, welke geconfigureerd worden binnen zone 17 to 32. Het zal hier dus niet gaan om alarmmeldingen maar om technische meldingen. Deze input wordt op het LCD scherm als volgt weergegeven: a. Gebouw melding b. Huidig zichtbare melding c. Totaal aantal meldingen Automatische alarmen - Wat doen d. Zone nummer e. Adres van het element f.
NF30/50 Reeks - Gebruikershandleiding 4 Bedieningsacties op de centrale 4.1 Inleiding Gebruikersacties op het paneel vereisen het intoetsen van de juiste druktoets en toegangscode. Het LCD en de gebruikerstoetsen op het panneel laten ons toe de volgende acties uit te voeren: a. Reset van het systeem. b. Stop zoemer. d. Transmissie aan of uit plaatsen, indien aanwezig in het systeem. e. Menu navigatie en invoer via alfanumerieke toetsen. f. Testen. g.
NF30/50 Reeks - Gebruikershandleiding 4.1.2 Interne Zoemer A B Het paneel beschikt over een interne zoemer die een plaatselijk waarschuwingssignaal geeft zodra één van de volgende toestanden wordt gedetecteerd: a. Brand. b. Storing. Bedieningsacties op de centrale 4.1.3 Toegangscodes Handelingen in deze handleiding vragen niveau 2 toegang (code of sleutel), maar een code niveau 3 mag ook gebruikt worden. Doorheen deze handleiding staat een ‘U’ vergezeld met een nummer voor een toegangscode niveau 2.
NF30/50 Reeks - Gebruikershandleiding 4.1.4 Sleutelschakelaar Het paneel is uitgerust met een sleutelschakelaar wat een alternatief geeft voor het toegangsniveau 2. Plaatsen we de sleutelschakelaar in de AAN – positie, dan bevinden we ons in toegangsniveau 2. Komt er een brand melding, dan kunnen we onmiddellijk de controletoetsen bedienen zonder het ingeven van een niveau 2 paswoord. Met de sleutelschakelaar in de AAN- stand kunnen we in de niveau 2 menu’s gaan door op de ‘ ’ toets te drukken 4.
NF30/50 Reeks - Gebruikershandleiding 4.4 STOP/HERSTART SIRENES Toets Bedieningsacties op de centrale De term “STOP” die in deze handleiding wordt gebruikt, beschrijft een tijdelijke status waarin het paneel komt wanneer de drukknop STOP /HERSTART SIRENES is ingedrukt. Drukken we tijdens een alarm op deze toets, dan worden de sirenes uitgeschakeld. Wanneer het paneel zich in de ge-STOPte staat bevindt, zal een nieuwe brandmelding alle voordien gedempte sounders opnieuw laten klinken.
NF30/50 Reeks - Gebruikershandleiding 4.5 TRANSMISSIE AAN / UIT Toets De TRANSMISSIE AAN / UIT toets plaatst de transmissie- uitgangen in of buiten dienst afhankelijk van de status waarin we ons bevinden. Deze functie is wel enkel van toepassing wanneer uitgang A als transmissieuitgang gedefinieerd werd tijdens de programmatie. Voor de transmissie-uitgangen in of buiten dienst te plaatsen gaan we als volgt te werk: a. Druk op de TRANSMISSIE AAN / UIT toets. b. Geef een correcte pascode niveau 2 in.
NF30/50 Reeks - Gebruikershandleiding 4.6 Alfanumerieke Toetsen Wanneer u een alfanumerieke toets gebruikt, wordt iedere operatie door een duidelijk hoorbaar piepsignaal bevestigd. Op niveau 1 hebben de alfanumerieke toetsen GEEN functie, tot er een alarmtoestand optreedt. In het geval van een alarmconditie worden de toetsen ‘ 2 ’ en ‘ 8 ’ geactiveerd, waarmee de gebruiker doorheen de alarmmeldingen kan gaan scrollen.
NF30/50 Reeks - Gebruikershandleiding 4.7 Niveau 2 Menu De volgende niveau 2 menu’s zijn beschikbaar nadat een correcte pascode niveau 2 wordt ingegeven of de sleutelschakelaar in de AAN stand wordt geplaatst. Bedieningsacties op de centrale De onderstaande menuboom biedt u een overzicht van de beschikbare niveau 2 menu’s. Het PROGRAMMEER menu staat hier in het grijs afbeeld omdat voor dit item een pascode niveau 3 nodig is.
NF30/50 Reeks - Gebruikershandleiding 4.8 TEST - Gebruikersoptie Volgende tests zijn beschikbaar vanaf toegangsniveau 2 in het Test – Gebruikersmenu: a. LED’s. b. LCD. c. ZONES. d. AUTO TEST. e. UITGANGEN. f. BUZZER. Bedieningsacties op de centrale g. Keyboard. Om in het TESTmenu te komen gaan we als volgt te werk: ’ toets in het Toestand: NORMAAL 1 Druk op de ‘ scherm. Het systeem vraagt naar een pascode niveau 2 of 3. (Druk op ‘ 4 ’ om te annuleren). BEPERKTE TOEGANG TOT MENUS Geef paswoord niv.
NF30/50 Reeks - Gebruikershandleiding 4.8.1 LED’s - Gebruikersoptie Deze optie uit het Test gebruikersmenu licht elke led om beurt op. Geef pascode niveau 2 in en doe het volgende om de led’s te testen: 1 Druk ‘ 1 ’ op het toetsenbord om in het TEST menu te komen. [U0] 1:TEST 2:IN/BUITEN DIENST 3:KLOK 4:DISPLAY MODE 5:PROGRAMMEER 2 Voor de LED - test drukken we de ‘ toetsenbord.
NF30/50 Reeks - Gebruikershandleiding 4.8.3 ZONES - Gebruikersoptie Wanneer u de optie ZONES in het TEST - gebruikersmenu selecteert,kunt u een ‘loop test’ uitvoeren per zone. Tijdens de loop test branden de IN TEST led en de desbetreffende ZONE STORING/TEST/BUITEN DIENST led waarmee aangegeven wordt dat deze zone zich in test bevind. U kunt een loop-TEST als volgt uitvoeren: 1 1 Druk op de ‘ 3 ’ toets op het numeriek klavier om de loop-TEST procedure te selecteren.
NF30/50 Reeks - Gebruikershandleiding 3 De loop-TEST beëindigen: a. Voor een specifieke zone: Druk op de ‘ 3 ’ toets binnen het Test Zones gebruikersmenu om het ‘Toon/Stop Test’ menu te openen. of 8 [STOP LOOP-TEST] Selecteer Zone: 01 ✓ : Stop ↕ : Wijzig <:Annuleer 5 i Gebruik de ‘ 2 / selecteren, en de ‘ ’ toetsen om de gewenste zone te 8 5 ’ toets om de zone te bevestigen.
NF30/50 Reeks - Gebruikershandleiding Testen van elementen Gebruik de volgende methoden om elementen te testen tijdens een Loop-Test: i. Test melders door ze bloot te stellen aan rook of warmte, afhankelijk van het type melder, of door het interne test contact te activeren m.b.v. een magneet. ii. Test drukknoppen m.b.v. een test-sleutel.
NF30/50 Reeks - Gebruikershandleiding 4.8.5 UITGANGEN - Gebruikersoptie De ‘UITGANGEN’ test van het Test menu, test alle interne alarmgevers en relay circuits evenals de uitgangen op de lus. Om deze test uit te voeren doen we de volgende handelingen: Test Interne Uitgangen 5 1 Vanuit het Test menu drukken we op de ‘ de ‘UITGANGEN’ optie te selecteren. 5 ’ toets om 1 [U0 uitgangen] 1:Intern 2:LUS 2 Op het scherm wordt het ‘uitgangen’ menu weergegeven.
NF30/50 Reeks - Gebruikershandleiding 4.8.6 BUZZER - Gebruikersoptie De BUZZER optie in het Test menu, test de interne zoemer. Ga voor deze test als volgt tewerk: 1 Druk ’ 1 ’ op het numeriek toetsenbord om in het TEST menu te komen. 1 [U0] 1:TEST 2:IN/BUITEN DIENST 3:KLOK 4:DISPLAY MODE 5:PROGRAMMEER 2 Gebruik de ‘ 2 / 8 ’ toetsen om meer opties weer te Bedieningsacties op de centrale geven. Nu drukken we op de ‘ 6 ’ toets van het numeriek klavier om de test te starten.
NF30/50 Reeks - Gebruikershandleiding 4.9 IN / BUITEN DIENST - Gebruikersoptie Afhankelijk van de toestand waarin we ons bevinden laat deze optie ons toe volgende zaken in- of buiten dienst te plaatsen: a. Zone (Element of volledige zone). b. Uitgangen. c. Dag Mode. d. Vertragingen. ’toets in het Toestand: NORMAAL 1 Druk op de ‘ scherm. Het systeem vraagt nu een pascode niv. 2/3. BEPERKTE TOEGANG TOT MENUS Geef paswoord niv.
NF30/50 Reeks - Gebruikershandleiding 4.9.1 Zone - Gebruikersoptie Deze optie brengt de gebruiker in de mogelijkheid een zone of een deel ervan IN / of BUITEN DIENST te plaatsen. Hiervoor gaan we als volgt te werk: 1 Druk op de ‘ 1 ’ toets op het numeriek klavier om de IN/BUITEN DIENST ‘Zone’ optie te selecteren. [U0 IN/BUITEN DIENST] 1:Zone 2:Uitgangen 3:Day mode 1 2 Het scherm toont de ‘Zone’ optie en vraagt om een zonenummer in te geven.
NF30/50 Reeks - Gebruikershandleiding 2 b. Een individueel element - Druk ‘ element’ optie te selecteren: 2 [IN/BUITEN DNST] Zone 01 1:Zone 2:Individueel Element ’ om de ‘Individueel Deel b. dienst ↕ : Meer 5 Om een individueel element te selecteren gebruiken we de ‘ 2 / 8 ’ toetsen om de nodige elementen zichtbaar te maken, ‘ 8 5 ’ om te bevestigen. [IN D] Zone 01 - IN DIENST S02 ? Druk ✓ Om te bevestigen <:Annuleer 2 [BUITEN D] Zone 01 - Buit. Dnst.
NF 30/50 Reeks - Gebruikershandleiding 4.9.2 Uitgangen - Gebruikersoptie De ‘Uitgangen’ optie stelt de gebruiker in staat alle sirenes, blus systemen (indien aanwezig), relais en controle uitgangen IN- of BUITEN DIENST te zetten.
NF 30/50 Reeks - Gebruikershandleiding 4.9.3 Dag mode - Gebruikersoptie Indien de Dag Mode functie geconfigureerd is tijdens de programmatie, kan de gebruiker deze optie gebruiken om dag mode vertragingen in of buiten dienst te plaatsen. Dit heeft geen effect op melder gevoeligheden die geprogrammeerd zijn. De melder gevoeligheid zal automatisch veranderen op de geprogrammeerde ‘Begin’ en ‘Eind’ tijden van de dag mode.
NF 30/50 Reeks - Gebruikershandleiding 4.9.4 Vertragingen - Gebruikersoptie De ‘Vertragingen’ functie van het systeem geeft de gebruiker de mogelijkheid om de tijdens programmatie gedefinieerde, vertragingen in of buiten dienst te plaatsen. (verwijs naar NF30/50 Installatie handleiding Sectie 5.5.3 Primary/Extend Delay Timers en 5.7.8 CBE Zones).
NF 30/50 Reeks - Gebruikershandleiding 4.10 Klok - Gebruikersoptie De ‘KLOK’ optie in het gebruikersmenu laat de gebruiker toe volgende zaken te veranderen: a. Tijd. b. Datum. Om in het ‘KLOK’ menu te komen: BEPERKTE TOEGANG TOT MENUS Geef paswoord niv. 2/3 < : Pijltje links Nota: Bij het ingeven van een verkeerd paswoord verschijnt de boodschap !!! ONGELDIG PASWOORD !!! op het scherm waarna het systeem naar het Toestand: NORMAAL scherm terugkeert.
NF 30/50 Reeks - Gebruikershandleiding 4.10.1 Tijd - Gebruikersoptie De ‘Tijd’ gebruikersfunctie laat de gebruiker toe om de tijd die op het scherm weergegeven wordt in te geven of aan te passen. Ga hiervoor als volgt te werk: 1 Druk op de ‘ 1 ’ toets van het numeriek klavier om de tijd - functie te selecteren. [U0 Klok] 1 : Tijd 2 : Datum Bedieningsacties op de centrale 1 2 Het systeem vraagt nu om de tijd in te geven. Gebruik het numeriek klavier om de cijfers direct in te brengen.
NF 30/50 Reeks - Gebruikershandleiding 4.10.2 Datum - Gebruikersoptie De ‘Datum’ gebruikersfunctie laat de gebruiker toe om de datum die op het scherm weergegeven wordt in te geven of aan te passen. Ga hiervoor als volgt te werk: 1 Druk op de ‘ 2 ’ toets van het numeriek klavier om de datum - functie te selecteren. 2 1 : Tijd 2 : Datum 2 Het systeem vraagt nu om de datum in te geven. Gebruik het numeriek klavier om de cijfers direct in te brengen.
NF 30/50 Reeks - Gebruikershandleiding 4.11 DISPLAY MODE - Gebruikersoptie De DISPLAY MODE gebruikersoptie laat de gebruiker toe volgende zaken de bekijken: a. Log b. Elementen op de lus c. Storingen d. Gebouw meldingen e. Zaken buiten dienst op de lus f. Alarm teller Bedieningsacties op de centrale g. Spanningsniveaus h. Versie (systeem en lus software) Om in het DISPLAY MODE menu te komen: 1 In het Toestand: NORMAAL scherm, Druk ‘ systeem vraagt een niv. 2/3 pascode. ’.
NF 30/50 Reeks - Gebruikershandleiding 4.11.1 Log - Gebruikersoptie De Log gebruikersoptie geeft de gebruiker de mogelijkheid alle gelogde evenementen te bekijken. Ga als volgt te werk om het logboek te bekijken: 1 Druk ‘ 1 ’ op het numeriek klavier om de log - functie te selecteren. [U0 Toon] 1:Log 3:Storingen 1 2:Elementen 4:Gebouw ↕ : Meer Gebruik de ‘ 2 / 8 ’ toetsen om door de events te scrollen. Hieronder zijn enkele voorbeeld events weergeven.
NF 30/50 Reeks - Gebruikershandleiding 4.11.2 Elementen - Gebruikersoptie De ‘Elementen’ gebruikersoptie geeft de gebruiker de mogelijkheid om alle elementen van de lus apart te observeren. Ga als volgt te werk: 1 Druk ‘ 2 ’ op het numeriek klavier om het Elementen menu te openen. [U0 Toon] 1:Log 3:Storingen 2 2:Elementen 4:Gebouw ↕ : Meer 2 Het LCD toont automatisch het laagste melderadres. Bedieningsacties op de centrale Gebruik de ‘ scrollen.
NF 30/50 Reeks - Gebruikershandleiding 4.11.3 Storingen - Gebruikersoptie Deze functie laat de gebruiker toe om alle aanwezige storingen te zien wanneer deze door een boodschap met hogere prioriteit (alarmen) overschreven zijn op het LCD scherm. Om deze storingen te zien drukken we: 1 ‘ 3 ’ op het numeriek klavier om de ‘Storingen’ functie te selecteren. [U0 Toon] 1:Log 3:Storingen 2:Elementen 4:Gebouw ↕ : Meer de ‘ 2 / 8 ’ toetsen om door de storingsmeldingen te scrollen.
NF 30/50 Reeks - Gebruikershandleiding 4.11.4 Gebouw - Gebruikersoptie De ‘Gebouw’ functie binnen het menu geeft de gebruiker de mogelijkheid alle actieve systeem waarschuwingen te bekijken indien ze door boodschappen met hogere prioriteit van het basisscherm verdrongen zijn. Om deze te zien vanuit het ‘Toon’ menu: 1 Druk ‘ 4 ’ op het numeriek klavier om de ‘Gebouw’ optie te selecteren.
NF 30/50 Reeks - Gebruikershandleiding 4.11.5 Buiten dienst - Gebruikersoptie De ‘Buiten dienst’ gebruikersoptie stelt de gebruiker in staat te zien welke luselementen buiten dienst zijn. Vanuit het ‘Toon’ menu gaan we als volgt te werk om deze functie te gebruiken: 1 Gebruikmakend van het numeriek klavier drukken we ‘ 5 ’ om het Buiten dienst menu te openen. [U0 Toon] 5 5:Buiten dienst 6:Alarm teller ↕ : Meer a.
NF 30/50 Reeks - Gebruikershandleiding 4.11.7 Spannings niveaus - Gebruikersoptie Met de ‘Spannings niveaus’ functie is het mogelijk spanningswaarden van enkele delen van het systeem op te vragen. Hiervoor drukken we: 1 ‘ 7 ’ op het numeriek klavier om het ‘Spannings niveaus’ menu te openen. 7 [U0 Toon] 7:Spannings niveaus 8:Versie ↕ : Meer Bedieningsacties op de centrale 2 Het ‘Battery spanning’ scherm opent automatisch. Gebruik de ‘ scrollen. [U0 VOLT] BATTERY SPANNING = 27.
NF 30/50 Reeks - Gebruikershandleiding 4.11.8 Versie - Gebruikersoptie De ‘Versie’ optie in het ‘Toon’ menu geeft de gebruiker de mogelijkheid het onderdeel nummer met de bijhorende software versie van het systeem en de luskaart op te vragen. Dit doen we als volgt: 1 Druk op de ‘ 8 ’ toets op het numeriek klavier om het ‘Versie’ menu te openen. [U0 Toon] 8 7:Spannings niveaus 8:Versie ↕ : Meer ‘ 4 ’ om het menu te verlaten en terug naar het ‘Toon’ menu te keren.
Bedieningsacties op de centrale NF 30/50 Reeks - Gebruikershandleiding v0903 42
NF30/50 Reeks - Gebruikershandleiding Bijlage 1 - Logboek In overeenstemming met EN54 deel 14 is de gebruiker verantwoordelijk voor het bijhouden van een logboek en daarin alle voorvallen te noteren die een gevolg zijn van, of een effect hebben op het systeem. Het logboek moet worden bewaard op een plaats die toegankelijk is voor bevoegde personen (bij voorkeur in de buurt van de centrale).
NF30/50 Reeks - Gebruikershandleiding Gegevens van de voorvallen Tijd Melding Vereiste actie Bijlage 1 - Logboek Datum v0903 A1 - 2 datum einde Initialen
NF30/50 Reeks - Gebruikershandleiding Gegevens van de voorvallen Tijd Melding Vereiste actie datum einde Initialen Bijlage 1 - Logboek Datum A1 - 3 v0903
NF30/50 Reeks - Gebruikershandleiding Gegevens van de voorvallen Tijd Melding Vereiste actie Bijlage 1 - Logboek Datum v0903 A1 - 4 datum einde Initialen
NF30/50 Reeks - Gebruikershandleiding Bijlage 2 - Onderhoud Maak een logboek (zie Bijlage 1) in overeenkomst met de aanbevelingen van EN54 Deel 14. Dit logboek moet worden gebruikt en onderhouden voor het noteren van voorvallen, zoals hierna beschreven. A2.1 Routinecontroles Teneinde er zeker van te zijn dat het systeem volledig operationeel is en voldoet aan de vereisten van EN54 Deel 14 en BS 5839 Deel 1: 1988, moeten de volgende routinecontroles worden uitgevoerd.
Bijlage 2 - Onderhoud NF30/50 Reeks - Gebruikershandleiding v0903 A2 - 2
NF30/50 Reeks - Gebruikershandleiding Bijlage 3 Verschillen tussen NF30 en NF50 Het verschil tussen de NF30 en NF50 panelen is dat de NF50 het gebruik van Very Intelligent Early Warning (VIEWTM) laser melders ondersteunt. Deze bijlage beschrijft de verschillen voor de gebruiker als we gebruik maken van een NF50 paneel. Callibratie wordt automatisch voor elke melder uitgevoerd, ongeveer 60 sec. nadat de melder op een paneel dat in rust is geïnstalleerd wordt.
Bijlage 3 - NF50 verschillen NF30/50 Reeks - Gebruikershandleiding v0903 A3 - 2
Av. de l’Expansion 16d B-4432 ALLEUR Belgium +32 (0)4 247 03 00 +32 (0)4 247 02 20 Pompmolenlaan 43a 3447 GK WOERDEN The Netherlands +31 (0)348 434 995 +31 (0)348 434 962 local distributor Every care has been taken in the preparation of this document but no liability can be accepted for the use of the information therein. Design features may be changed or amended without prior notice.