Owner's Manual

ManualsBrandsNotifier ManualsControl panelNFS2-3030

DN-7070:P • 3/8/17 — Page 1 of 8

NFS2-3030

Intelligent Addressable

Fire Alarm System

Intelligent Fire Alarm Control Panels

DN-7070:P • A-10

NFS2-3030 (left)

and NFS2-3030 with DVC audio option (right)

7070covg.jpg

General

The NFS2-3030 is an intelligent Fire Alarm Control Panel

(FACP) designed for medium- to large-scale facilities. Fire

emergency detection and evacuation are extremely critical to

life safety, and the NFS2-3030 is ideally suited for these appli-

cations. The NFS2-3030 is part of the ONYX

Series of prod-

ucts from NOTIFIER. The NFS2-3030 is ideal for virtually any

application because it features a modular design that is config-

ured per project requirements. With one to ten Signaling Line

Circuits (SLCs), the NFS2-3030 supports up to 3,180 intelli-

gent addressable devices.

Information is critical to fire evacuation personnel, and the

NFS2-3030’s large 640-character Liquid Crystal Display (LCD)

presents vital information to operators concerning a fire situa-

tion, fire progression, and evacuation details.

A host of other options are available, including single- or multi-

channel voice; firefighter’s telephone; LED, LCD, or PC-based

graphic annunciators; networking; advanced detection prod-

ucts for challenging environments; wireless fire protection; and

many additional options.

Features

• Certified for seismic applications when used with the appro-

priate seismic mounting kit.

• Approved for Marine applications when a marine-listed ver-

sion is used with marine-listed compatible equipment. See

DN-60688.

• Complies with UL 2572 Mass Notification Systems (NFS2-

3030 version 20 or higher).

• One to ten isolated intelligent Signaling Line Circuits (SLC)

Style 4, 6 or 7.

• Wireless fire protection using SWIFT Smart Wireless Inte-

grated Fire Technology. See DN-60820.

• Up to 159 detectors and 159 modules per SLC; 318 devices

per loop/3,180 per FACP or network node.

– Detectors can be any mix of ion, photo, thermal, or multi-

sensor; wireless detectors are available for use with the

FWSG.

– Modules include addressable pull stations, normally open

contact devices, two-wire smoke detectors, notification, or

relay; wireless modules are available for use with the

FWSG.

• Large 16 line, 640 character LCD backlit display or use

display-less as a network node.

• Network options:

– High-speed network for up to 200 nodes (NFS2-3030,

NFS2-640, NFS-320(C), NFS-320SYS, NCA-2,

DVC-EM,

ONYXWorks, NFS-3030, NFS-640, and NCA).

–

Standard

network for up to 103 nodes (NFS2-3030,

NFS2-640, NFS-320(C), NFS-320SYS, NCA-2,

DVC-EM,

ONYXWorks, NCS, NFS-3030, NFS-640, NCA, AFP-200,

AFP-300/400, AFP-1010, and AM2020). Up to 54 nodes

when

DVC-EM is used in network paging.

• Built-in Alarm, Trouble, Security, and Supervisory relays.

• VeriFire

Tools online/offline program option.

• With built-in Degraded Mode operation, the system is capa-

ble of general alarm if a fire alarm condition is present even

if the central processing unit (CPU) fails.

• Weekly Occupancy Schedules allow changing sensitivity by

time of day and day of week.

• EIA-485 annunciators, including custom graphics.

• History file with 4000-event capacity in nonvolatile memory,

plus separate 1000-event alarm-only file.

• Advanced history filters allow sorting by event, time, date,

or address.

• Alarm Verification selection per point, with automatic

counter.

• Autoprogramming and Walk Test reports.

• Multiple central station communication options:

– Standard UDACT

– Internet

– Internet/GSM

• Positive Alarm Sequence (PAS) Presignal.

• Silence Inhibit and Auto Silence timer options.

• Field-programmable on panel or on PC, with VeriFire Tools

program, also check, compare.

• Non-alarm points for lower priority functions.

• Remote ACK/Signal Silence/System Reset/Drill via monitor

modules.

• Up to 1000 powerful Boolean logic equations.

• Supports SCS Series smoke control system in both HVAC

and FSCS modes.

• FM6320 approved Gas Detection System with FMM-4-20

module and any FM listed gas detector.

• EIA-232 printer port.

• EIA-485 annunciator port.

firealarmresources.com

Summary of content (8 pages)

PAGE 1
DN-7070:P • A-10 NFS2-3030 Intelligent Addressable Fire Alarm System Intelligent Fire Alarm Control Panels General The NFS2-3030 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. Fire emergency detection and evacuation are extremely critical to life safety, and the NFS2-3030 is ideally suited for these applications. The NFS2-3030 is part of the ONYX® Series of products from NOTIFIER.
PAGE 2
640-CHARACTER DISPLAY FEATURES • Backlit, 640-character display. • Program keypad: full QWERTY keypad. • Up to nine users, each with a password and selectable access levels. • 11 LED indicators: Power; Fire Alarm; Pre-Alarm; Security; Supervisory; System Trouble; Other Event; Signals Silenced; Point Disabled; CPU Failure; Controls Active. • Membrane Switch Controls: Acknowledge; Signal Silence; Drill; System Reset; Lamp Test.
PAGE 3
FAPT-851 ACCLIMATE PLUS™ LOW-PROFILE INTELLIGENT MULTI-SENSOR • Detector automatically adjusts sensitivity levels without operator intervention or programming. Sensitivity increases with heat. • Microprocessor-based technology; combination photo and thermal technology. • Low-temperature signal at 40°F ± 5°F (4.44°C ± 2.77°C). • 35 watt, 50 watt, 75 watt, and 100/125 watt digital amplifiers (DAA2/DAX series and DS series). • Solid state message generation. • Hard-wired voice control module options.
PAGE 4
Field Programming Options Autoprogram is a timesaving feature. The FACP “learns” what devices are physically connected and automatically loads them in the program with default values for all parameters. Requiring less than one minute to run, this routine allows the user to have almost immediate fire protection in a new installation, even if only a portion of the detectors are installed. Keypad Program Edit.
PAGE 5
transfer relay, and overcurrent protection. Mounts on two of four positions on a CHS-4L or CHS-4 chassis. See DN-5952. ACPS-610: 6.0 A or 10.0 A addressable charging power supply. See DN-60244. FCPS-24S6/-24S8: Remote 6 A and 8 A power supplies with battery charger. See DN-6927. BAT Series: Batteries. AMPS-24 uses two 12 volt, 7 to 200 AH batteries. See DN-6933. AUDIO OPTIONS NOTE: See “Enclosures, Chassis, and Dress Plates” on page 6 for mounting hardware.
PAGE 6
FSA-20000: Intelligent FAAST® XT Fire Alarm Aspiration Sensing Technology. Intelligent aspirating smoke detector for applications up to 28,800 sq.ft. For Canadian applications, order FSA-20000A. See DN-60849. FMM-4-20: FlashScan 4-20 mA protocol monitor module. See DN-60411. FCM-1(A): FlashScan control module. See DN-6724. FSA-20000P FAAST® XT PRO Intelligent Aspiration Detector For applications up to 28,800 sq. ft. (2601 sq. m.) through one to four addressable pipes.
PAGE 7
on a half-chassis and one NFS2-3030 or NCA-2 mounted on a half-chassis. The right side houses a microphone/handset well. The CA-2 assembly includes CMIC-1 microphone. ADDR Series doors with two-tier visibility are available for use with the CA-2 configuration: ADDR-B4, ADDR-C4, ADDR-D4 (below). ADDR-B4: Two-tier-sized door designed for use with the CA-2 chassis configuration. ADDR Series doors are similar to CAB4 Series “DR” doors, but a clear window space exposes the top two tiers of the CAB-4 enclosure.
PAGE 8
– AMPS-24(E)*: 0.13 A. (Draws power from secondary power source only.) NOTE: See AMPS-24(E) Manual 51907 for a complete current draw calculation sheet and details of input and output values. Battery charger range: 7 AH – 200 AH. Use separate cabinet for batteries over 26 AH. Float Rate: 27.6 V. SHIPPING WEIGHT STANDARDS The NFS2-3030 complies with the following UL Standards and NFPA 72, International Building Code (IBC), and California Building Code (CBC) Fire Alarm Systems requirements: • UL 864 (Fire).