Installation Guide

ManualsBrandsNOTIFIER ManualsSupervised PIDNOTIFIER NION-2C8M Normally Closed Supervised PID

Document 51394 NION-2C8M-NCS Installation Rev. B 10/5/00

NION-2C8M Board Layout

Description of the NION-2C8M

The NION-2C8M (2 Control, 8 Monitor) is a discrete input/output interface used on the network. All of the system

components are based on LonWorks (Local Operating Network) technologies. The NION-2C8M provides a

gateway to the network for equipment and control panels that have dry contacts.

The NION-2C8M connects a LonWorks FT-10 or FO-10 network, and discrete monitored devices and conven-

tional control panels. It provides a single, two-way communication channel for discrete inputs and outputs when

connected to a control panel. NIONs are specific to the type of network to which they connect (FT-10 or FO-10).

The transceiver type must be specified and ordered separately when ordering the NION.

The NION-2C8M can be powered by any 24VDC power limited source with battery backup which is UL listed for

use with fire protective signaling units. Power must be supervised or placed within 20 ft of the NION with connec-

tions run in conduit.

The NION-2C8M mounts in an enclosure (NIS CAB-1 or CHS-4L in CAB-3 series enclosure) with conduit knock-

outs.

NION-2C8M-Normally Closed Supervised (NCS)

Product Installation Document

This document covers the procedures and specifications for installing the above listed unit and when appro-

priate, information regarding configuration on the monitored device. For more detailed configuration and

operation information, refer to Network Installation Manual, Echelon Local Area Server Manual, or BCI 3

Manual as appropriate.

Document 51394

10/5/00 Rev B

51394:B ECN 00-427

NOTE: DO NOT change the

factory default jumper settings

from what is shown in the

above diagram.

Output 1Output 2

Inputs 1-

10k EOL resistor

in parallel with

contact

Network

Transceiver

Connection

Output

Input

Status

Unbound

LEDs

GND

+24VDC

Binding

Alarm and

Trouble Input

LEDs

Input Configuration

Jumpers

Transceiver

Standoffs

Application

Code

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of content (3 pages)

PAGE 1
NION-2C8M-Normally Closed Supervised (NCS) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding configuration on the monitored device. For more detailed configuration and operation information, refer to Network Installation Manual, Echelon Local Area Server Manual, or BCI 3 Manual as appropriate.
PAGE 2
Installation Description The NION-2C8M can be installed in the following environmental conditions: · · Temperature range of 0ºC to 49ºC (32°F - 120°F). 93% humidity non-condensing at 30ºC (86°F). Mounting NOTE: Use only wire for power limited systems. Power limited wire runs use type FPLR, FPLP, FPL or equivalent cabling per NEC 760. The NION-2C8M is designed to be installed on a wall within 20 feet of the monitored equipment in the same room.
PAGE 3
I/O Configuration and Connections Inputs The NION-2C8M accepts eight normally open or normally closed dry contact inputs. Each input is monitored by an end-of-line resistor. These inputs are wired to a 16 point plug-in terminal strip in the following pattern: Input 1 point 1 = input line Input 8 through point 15 = input line point 2 = common point 16 = common The PCB is labeled and the terminals are numbered for convenience. Inputs are rated for 18V nominal, 1.