www. .ch WA 1658 User manual Washing Machine 0848 559 111 www.fust.
CONTENTS Safety information Product description Control panel First use Personalization Daily use Washing programmes 2 4 5 6 6 7 11 Helpful hints and tips 15 Care and cleaning 16 What to do if… 19 Technical data 22 Consumption values 23 Installation 23 Environment concerns 27 Subject to change without notice Important! Read carefully & keep for future reference.
• All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual. • After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall. • If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance.
PRODUCT DESCRIPTION Product description Your new appliance meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. The NEW JET system allows total use of detergent and reduces water consumption so saving energy. 2 1 3 4 6 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle Detergent dispenser drawer Compartment for detergent used for prewash. The prewash detergent is added at the beginning of the wash programme.
CONTROL PANEL Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and the display. These are presented by relevant numbers on the following pages. 9 1 2 3 1 Programme selector dial 2 TEMPERATURE button (TEMP.) 3 SPIN reduction button (U/MIN.
• The programme progress display shows the washing phases of the selected programme. • During a washing cycle, a black line blinks under the washing phase symbol of the running programme. At the end of each washing phase, the line under the corresponding symbol becomes fixed. If the OVERDOSAGE symbol lights up at the end of the programme, it indicates that too much detergent has been used. , STAIN , 9.4 - Options: PREWASH SENSITIVE , EXTRA RINSE 9.
Child safety lock This device permits you to leave the appliance unattended and not to worry that children might be injured by or cause damage to the appliance. This function remains able also when the washing machine is not working. To enable (or disable) this option press simultaneously for about 6 seconds buttons 4 and 5 until the Child Lock symbol appears on (or disappears from) the display.
must not exceed the MAX mark in the drawer). Close the drawer gently. Select the required programme by means of programme selector dial (1) You can choose the right programme for any type of laundry following the descriptions on the washing programme tables (see «Washing Programmes»). Turn the programme selector dial to the required programme. The programme selector determines the type of washing cycle (e.g.
ing the button 7. Press the button 4: all the option symbols appear on the display. To scroll all the available options, press the button 4. The corresponding symbol appears on the display and starts blinking. Press the button 5 to activate and confirm your choice. A black dash appears under the selected symbol to indicate that this option has been set. Press the same button to deactivate the option. After selecting the options, wait about few seconds until the display gets back to the default status.
If an incorrect option is selected, the yellow pilot light of the button 7 blinks 3 times and the message Err is displayed for a few seconds. Select the DELAY START (button 8) Before you start the programme, if you wish to delay the start, press the button repeatedly, to select the desired delay. The corresponding symbol will appear on the display. The wash programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button.
the below instruction to empty the water out: • turn the programme selector dial to • select the DRAINING or SPINNING programme • reduce the spin speed if needed, by means of the relevant button • press the button 7 • when the programme has finished the display shows a blinking . On the dis- play the DOOR symbol disappears and the door can be opened. to Turn the programme selector dial to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty.
Programme Maximum and Minimum Temperature Cycle Description Maximum Fabrics Load Type of Laundry Options JEANS JEANS 60° - Cold Main wash - Rinses - Long spin Max. load 4 kg With this programme it is possible to wash items like pants, shirts or jackets in Jeans and also jersey realized with hi-tech materials (the Extra Rinse option will be activated automatically). SPIN REDUCTION NIGHT CYCLE RINSE HOLD PREWASH1) PFLEGELEICHT -SYNTHETIQUES SYNTHETICS 60°- Cold Main wash - Rinses - Short spin Max.
Programme Maximum and Minimum Temperature Cycle Description Maximum Fabrics Load Type of Laundry Options PUMPEN - VIDANGE DRAIN Draining of water Max. load 8 kg For emptying out the water of the last rinse in programmes with the option selected, that ends with water left in the tub. SCHLEUDERN - ESSORAGE SPIN Drain and long spin Max. load 8 kg Separate spin for hand washed cotton garments and after programmes with the option selected that ends with water left in the tub.
Programme Maximum and Minimum Temperature Cycle Description Maximum Fabrics Load Type of Laundry Options SPORT INTENSIV - SPORT SPORT INTENSIVE 40° - Cold Prewash - Main wash - Rinses - Short spin Max. load 2.5 kg Special programme is suitable for washing heavily soiled sport items. The machine will add automatically a prewash phase before the main wash to eliminate mud stains. We recommend you NOT to put the decompartment of the detergent tergent into the drawer.
Programme Maximum and Minimum Temperature Cycle Description Maximum Fabrics Load Type of Laundry Options Detergent Compartment / AUS ARRET= OFF For cancelling the programme which is running or to switch the machine off . 1) If using liquid detergents, a programme without prewash must be selected. 2) Stain option can be selected only at the temperature of 40°C or higher. 3) If you select the Super Quick option by pressing button 6, we recommend that you reduce the maximum load as indicated.
The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.), the colour, washing temperature and degree of soiling. All commonly available washing machine detergents may be used in this appliance: • powder detergents for all types of fabric • powder detergents for delicate fabrics (60°C max) and woollens • liquid detergents, preferably for low temperature wash programmes (60°C max) for all types of fabric, or special for woollens only.
3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place. 5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6. Insert the detergent dispenser drawer in the guide rails and push it in. Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron.
Pull out the emergency emptying hose, place it in the container and remove its cap. 11. Replace the filter into the pump by inserting it correctly into the special guides. Screw the pump cover firmly by turning it clockwise. 12. Refit the flap and close the pump door. Warning! 7. When no more water comes out, unscrew the pump cover by turning it anti-clockwise and remove the filter. Use pliers, if necessary. Always keep a rag nearby to dry up any water spillages when removing the cover.
5. Unscrew the hose from the machine. Keep a rug nearby because some water may flow. 6. Clean the filter in the valve with a stiff brush or with the piece of cloth. 7. Screw the hose back to the machine and make sure the connection is tight. 8. Turn on the water tap. Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. close the water tap and unscrew the water inlet hose from the tap; 2.
Once the problem has been eliminated, press the button 7 to restart the proProblem gramme. If after all checks, the problem persists, contact your local Service Centre. Possible cause/Solution The washing machine does not start: The door has not been closed. • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown.
Problem Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (creates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. • Check the water inlet hose connection. The drain hose is damaged. • Change it with a new one.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after some minutes, the laundry is still not evenly distributed in the drum, the machine will not spin. • Redistribute the laundry.
Spin Speed Maximum 1600 rpm CONSUMPTION VALUES Programme Energy consumption (KWh) Water consumption (litres) White Cottons 95° 2.5 62 Cottons 60° 1.7 63 Cotton Energy Saving Programme 60° 1) 1.03 57 Cottons 40° 0.97 62 Synthetics 40° 0.55 51 Delicates 40° 0.54 68 Wool/ Handwash 30° 0.32 64 Programme duration (Minutes) For the duration of the programmes, please refer to the display on the control panel.
tic plug caps supplied in the bag containing the instruction booklet. 4. Slide out the relevant plastic spacers. 7. Connect the water inlet hose as described under the paragraph «Water inlet». 5. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal. 6. Fill the smaller upper hole and the two large ones with the corresponding plas- Positioning and levelling Install the machine on a flat hard floor.
The water inlet hose and the drain hose must not be kinked. Please ensure that when the appliance is installed, it is easily accessible for the engineer in the event of a breakdown. Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Water inlet An inlet hose is supplied and can be found inside the machine drum. This appliance must be connected to a cold water supply.
This could be done by tying it to the tap with a piece of string or attaching it to the wall. 2. In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground. 3. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked.
Important! The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Centre. ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment.
Warranty / customer service For each product we provide a two-year guarantee from the date of purchase or delivery to the consumer (with a guarantee certificate, invoice or sales receipt serving as proof). The guarantee covers the costs of materials, labour and travel.
Unsere Kundendienst-Telefonnummer: Le numéro de téléphone de notre service après-vente: Il nostro numero di telefono del servizio clientela: Our customer service telephone number: 0848 559 111 oder unter ou sur Internet oppure su Internet or in the internet www.fust.ch Dipl. Ing FUST AG Buchental 4 9245 Oberbüren Tel. (071) 955 50 50 Dipl. Ing. FUST AG Riedmoosstrasse 3172 Niederwangen-Bern Tel. (031) 980 11 11 Dipl. Ing. FUST AG An der Rheinstrasse 4414 Füllinsdorf Tel. (061) 906 95 00 Ing. dipl.
132941820-A-452010 www. .