User's Manual
Table Of Contents
- 1 Introduction
- 2 Module Power
- 3 Physical Interfaces
- Module Mounting to Host Board (Reference)
- Connectors
- Connectors
- I/O Connector Pin Assignments
- Circuit Protection
- Antenna
- Control Connector Signal Functions
- Module Power (Pins 85, 87, 89, 91, 93, 95, 97, 99)
- Power Control (Pin 35) - (PWR_CTL)
- Level Translation Reference Power (Pin 77)
- USB (Pins 1, 3, 5, 7, 9)
- General Purpose Input/Output Interface
- RTC Sleep
- Serial Interfaces & Handshake (Pins 11, 13, 15, 17, 19, 21, 23, 25)
- Multi-Channel Serial Interface (MCSI) – (Pins 12, 14, 16, 18)
- VBackup Input (Pin83)
- Using VBackup
- Analog-to-Digital Input (Pin 74)
- Handset Microphone Input (Pins 65, 67)
- Handset Microphone Bias Output (Pin 63)
- Handset Speaker Output (Pins 71, 73)
- Headset Microphone Input (Pin 55)
- Headset Microphone Bias Output (Pin 53)
- Headset Speaker Output Left & Right (Pins 57, 59)
- Headset Output Common Mode (Pin 61)
- Headset Detect (Pin 47)
- Subscriber Identity Module (SIM) Carrier (Pins 76, 78, 80, 82, 84)
- 4 Hardware Design
- General Design Guidelines for Using Novatel Wireless M2M GSM Modules
- Enabling the Transmission Modes for the GSM/GPRS Services
- Voice Communication
- Circuit-Switched Data
- SMS: Short Message Services
- Provisioning The SIM
- GSM Services Supported by the Novatel Wireless M2M Enabler IIIG Module
- GPRS Services Supported by the Novatel Wireless M2M Enabler IIIG Module
- Selecting the GSM Modes of Operation
- 5 Setup and Initialization
- 6 Integration and Testing
ix novatelwireless.com
d. The user manual/installation guide must give clear instructions regarding the
proper installation and use to ensure compliance with RF Exposure guidelines.
Note: The host manufacturer is responsible for all standalone regulatory requirements prior to
the integration of the M2M module (i.e. FCC Part 15 for unintentional radiators).
FCC Notice to Users
Novatel Wireless M2M has not approved any changes or modifications to this device by the
user. Any changes or modifications could void the users authority to operate the device. See
47 CFR Sec. 15.21. The device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation. See 47 CFR Sec. 15.19.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Refer to the following for FCC Regulations: