User's Manual
Table Of Contents
- Safety Precautions
- Regulatory Compliance FCC
- Manual Overview
- Introduction
- Technical Specifications
- Physical Interfaces
- Enabler II-G Mounting Reference
- Pin Orientation Reference
- Connectors
- I/O Signal Connector on the Enfora Enabler II-G Module
- Antenna
- Control Connector Signal Descriptions and Functions
- Input Power
- Ring Indicate
- Radio Power/Reset
- Serial Interface (9 Pin I/F) (See table in section 6.5.1 I/O Connector Pin Assignments)
- General Purpose Input/Output Interface (GPIO)
- Analog-To-Digital Input
- Digital-To-Analog Output
- Handset Microphone Input
- Handset Speaker Output
- Headset Microphone Input
- Headset Speaker Output
- Audio Design Note
- Subscriber Identity Module (SIM) Carrier
- Modes of Operation
- SIM Operation
- Software Interface
- Setup and Initialization
- General Setup
- HyperTerminal Configuration for Enabler II-G
- Initialization (AT Command Interface)
- Initial Response to the AT Command
- Sending an Initialization String to the Enfora Enabler II-G Module
- Setting Up the Communication Mode for the Enfora Enabler II-G Module
- Querying the Status of the Enfora Enabler II-G Module
- Setting Module Reporting Parameters for GSM and GPRS
- GSM/SMS Examples
- GPRS Packet Examples
- General Setup
- Integration and Testing
- APPENDIX A - Warranty Repair and Return Policy
- APPENDIX B - Regulations and Compliance
- GCF Approval (Formerly FTA)
- Electromagnetic Compatibility (EMC) and Safety Requirements
- EMC/Safety Requirements for the USA
- Human Exposure Compliance Statement
- Compliance with FCC Regulations
- Unintentional Radiators, Part 15
- Intentional Radiators, Part 24
- Instructions to the Original Equipment Manufacturer (OEM)
- Nationally Recognized Testing Laboratory (NRTL) Approval
- EMC/Safety Requirements for the Countries of the European Union (EU)
- EMC/Safety Requirements for Other Countries
- APPENDIX C - Glossary and Acronyms
- APPENDIX D – Tables And Figures
- APPENDIX E - Contacting Enfora
Integration Guide
Version 1.07
GSM0100PB001 Page 47 1.07 - 1/9/04
10.1.6 Querying the Status of the Enfora Enabler II-G Module
This topic is addressed in the Enfora Application Note GSM0000AN006 – Enabler-G Module Status
Query.
10.1.7 Setting Module Reporting Parameters for GSM and GPRS
This topic is addressed in the Enfora Application Note GSM0000AN007 - Enabler-G Status Reporting.
10.2 GSM/SMS Examples
10.2.1 Initialize the Enfora Enabler II-G Module to Send and Receive SMS Text Messages
This topic is addressed in the Enfora Application Note GSM0000AN004 - Enabler-G SMS Configuration
and Use.
10.2.2 Managing SMS Messages
This topic is addressed in the Enfora Application Note GSM0000AN004 - Enabler-G SMS Configuration
and Use.
10.2.3 Data Call Configuration
This topic is addressed in the Enfora Application Note GSM0000AN003 - Enabler-G Data Circuit Switched
Call Configuration and Use.
10.2.4 Voice Call Configuration
This topic is addressed in the Enfora Application Note GSM0000AN003 - Enabler-G Data Circuit Switched
Call Configuration and Use.
10.3 GPRS Packet Examples
10.3.1 GPRS ATTACH and ACTIVATE
This topic is addressed in the Enfora Application Note GSM0000AN005 - Enabler-G Automated Network
Connection Configuration and Use.
10.3.2 Windows PPP Setup
The Enabler II-G module can be used in a Windows operating system environment as a standard serial
modem device. The required setup and configuration process is contained in Enfora Application Notes
GSM0000AN001 - Enabler-G PPP Configuration for Windows 98 and GSM0000AN002 - Enabler-G PPP
Configuration for Windows 2000.