User Manual

ManualsBrandsNSi Industries ManualsEquipmentDG180 Old Series

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

and SKIP modes. Press to advance the Month in the

DATE mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance Date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the Schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to alter the Load status and/or to

Override scheduled event.

MODE: Press to advance to next mode without

affecting the display information. Sequence is: RUN,

CLK, DATE, schedule SET, SKIP. In the SET mode,

unit automatically reverts to the RUN mode if no

entries are made for a short time.

SP DAY: Press to set or delete SKIP days (those on

which no schedule is executed)

ON/OFF: Pressing each time will select ON or OFF

EVENT. Multiple OFF’s may be scheduled to cancel

override ON’S

ENTER: Press to store the displayed information into

memory. Information will not be stored until

ENTER is pressed.

NOTE: During settings, each press of the key will

advance one number. For rapid advance, hold key in.

DAY

MONTH

HOUR

DATE

MIN

YEAR

OVER-

RIDE

MODE

DAY

ON/

OFF

ENTER

TORK DG180

DIGITAL TIME SWITCH

24 HOUR WITH DAY OMIT

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel controller

24 Hour scheduling with day omitting

288 Set points in 5 minute increments

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual override to the next scheduled event

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

Summary of content (7 pages)

PAGE 1
TORK DG180 DIGITAL TIME SWITCH 24 HOUR WITH DAY OMIT READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT FEATURES Single channel controller NOTE: Unit can be fully programmed using battery power only. 4. Reinstall unit by reversing step #1 above and connect wires to unit as per suggested wiring diagrams. See illustration on enclosure label.
PAGE 2
TORK DG180 DIGITAL TIME SWITCH 24 HOUR WITH DAY OMIT READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT FEATURES Single channel controller NOTE: Unit can be fully programmed using battery power only. 4. Reinstall unit by reversing step #1 above and connect wires to unit as per suggested wiring diagrams. See illustration on enclosure label.
PAGE 3
SETTING THE UNIT TO SET CLOCK SELECT AM/PM OR 24 HOUR MILITARY FORMAT Upon powering up the unit, model number 180 appears on the screen. The LCD will next display 12H which is an automatic (AM/PM) format. Press MODE key; display shows CLK. SU AM CLK Press DAY/MONTH key to select today’s day. Press HOUR key to set present hour (check AM/PM). Press MIN key to set present minutes. Press ENTER key. Unit now stores present time. Seconds are set to zero.
PAGE 4
SETTING THE UNIT TO SET CLOCK SELECT AM/PM OR 24 HOUR MILITARY FORMAT Upon powering up the unit, model number 180 appears on the screen. The LCD will next display 12H which is an automatic (AM/PM) format. Press MODE key; display shows CLK. SU AM CLK Press DAY/MONTH key to select today’s day. Press HOUR key to set present hour (check AM/PM). Press MIN key to set present minutes. Press ENTER key. Unit now stores present time. Seconds are set to zero.
PAGE 5
Press mode key until display shows DATE. DATE Press MONTH key to select month. Press DATE key to set today’s date. Press YEAR key to set present year. Press ENTER key. Unit now stores present date. Note: If unit has correct entry for the calendar, then the unit will go into the SET mode. If the calendar has an incorrect entry, then the unit will stay in the DATE mode, with MM--YY displayed, signifying that the date does not correspond with the month, and/or year, i.e. Feb. 31,1989.
PAGE 6
Press mode key until display shows DATE. DATE Press MONTH key to select month. Press DATE key to set today’s date. Press YEAR key to set present year. Press ENTER key. Unit now stores present date. Note: If unit has correct entry for the calendar, then the unit will go into the SET mode. If the calendar has an incorrect entry, then the unit will stay in the DATE mode, with MM--YY displayed, signifying that the date does not correspond with the month, and/or year, i.e. Feb. 31,1989.
PAGE 7
6. To skip schedules on all days (such as for vacation shut-down) press the SP DAY key when unit is in the run mode. Current day of the week will flash and a “D” will appear in the upper right display. To resume normal schedule, press SP DAY key again. REVIEW/MODIFY SCHEDULE: 1. Press MODE key until display shows SET. The first chronological event will be displayed. 2. Press ENTER repeatedly to continue reviewing the other scheduled ON/OFF events. 3.