Owner manual

ManualsBrandsNSi Industries ManualsEquipmentDGM100 Old Series

TORK DGM100

DIGITAL TIME SWITCH

SEVEN DAY

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel controller

7 day scheduling

Special day scheduling

32 set points

2 second momentary output for use with low voltage

latching relays, mechanically held contactors, electri-

cally (magnetically) held contactors.

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual override to the next scheduled event

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

Unit contains 2 SPDT relays. Left relay will close

for 2 seconds between C & NO when an ON pulse

is scheduled. Right relay will close for 2 seconds

between C & NO when an OFF pulse is scheduled.

NOTE: C & NC of right relay is used to OPEN elec-

trically held contactors.

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

mode. Press to advance the Month in the DATE

mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance Date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the Schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to alter the Load status and/or to

Override scheduled event.

MODE: Press to advance to next mode without

affecting the scheduled memory information.

Sequence is: RUN, CLK, DATE, schedule SET. In

the SET mode, unit automatically reverts to the

RUN mode if no entries are made for 5 minutes.

SP DAY: Press during RUN mode to execute the

“SPECIAL DAY” schedule everyday. LCD will display

D in upper right corner. Pressing SP DAY again will

toggle the unit back to normal 7 day program opera-

tion.

DAY

MONTH

HOUR

DATE

MIN

YEAR

OVER-

RIDE

MODE

DAY

ON/

OFF

ENTER

Summary of content (7 pages)

PAGE 1
TORK DGM100 DIGITAL TIME SWITCH SEVEN DAY 3. Install a standard 9 volt lithium or alkaline battery (not supplied) by gently squeezing the right side of the battery cover on the front of the unit and pull to open. Pull out the battery connector and connect the battery. Reinstall battery cover. Lithium should be replaced every 3-5 years, Alkaline every year. READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT NOTE: Unit can be fully programmed using battery power only.
PAGE 2
TORK DGM100 DIGITAL TIME SWITCH SEVEN DAY 3. Install a standard 9 volt lithium or alkaline battery (not supplied) by gently squeezing the right side of the battery cover on the front of the unit and pull to open. Pull out the battery connector and connect the battery. Reinstall battery cover. Lithium should be replaced every 3-5 years, Alkaline every year. READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT NOTE: Unit can be fully programmed using battery power only.
PAGE 3
ON/OFF: Pressing each time will select ON or OFF pulse. Multiple OFF pulses may be scheduled to cancel override ON pulses. ENTER: Press to store the displayed information into memory. Information will not be stored until ENTER is pressed. TO SET CLOCK Press MODE key; display shows CLK. SU AM NOTE: During settings, each press of the key will advance one number. For rapid advance, hold key in. CLK SETTING THE UNIT SELECT AM/PM OR 24 HOUR MILITARY FORMAT Press DAY/MONTH key to select today’s day.
PAGE 4
ON/OFF: Pressing each time will select ON or OFF pulse. Multiple OFF pulses may be scheduled to cancel override ON pulses. ENTER: Press to store the displayed information into memory. Information will not be stored until ENTER is pressed. TO SET CLOCK Press MODE key; display shows CLK. SU AM NOTE: During settings, each press of the key will advance one number. For rapid advance, hold key in. CLK SETTING THE UNIT SELECT AM/PM OR 24 HOUR MILITARY FORMAT Press DAY/MONTH key to select today’s day.
PAGE 5
Press MONTH key to set present month. Press DATE key to set today’s date. Press YEAR key to set present year. Press ENTER key. Unit now stores present date. Display will now show —:—02. This tells you that the first event has been entered, and that the unit is ready to accept the second entry. Repeat above steps 1 to 4 to set more schedule events Note: If unit has correct entry for the calendar, then the unit will go into the SET mode.
PAGE 6
Press MONTH key to set present month. Press DATE key to set today’s date. Press YEAR key to set present year. Press ENTER key. Unit now stores present date. Display will now show —:—02. This tells you that the first event has been entered, and that the unit is ready to accept the second entry. Repeat above steps 1 to 4 to set more schedule events Note: If unit has correct entry for the calendar, then the unit will go into the SET mode.
PAGE 7
MODIFY: During the review process, the DAY HOUR, MIN. and ON/OFF keys can all be used to modify the settings. You can use the first three keys to modify when the event will take place, and the ON/OFF key to change an ON pulse to an OFF pulse, or visa-versa. ONCE YOU HAVE MADE THE NECESSARY CHANGE, YOU MUST PRESS THE ENTER KEY TO STORE THEM. ADD: You may add events at any time by pressing the mode key until the unit is in the set mode. Then press ENTER key to advance to the next open set point.