Manual

ManualsBrandsNSi Industries ManualsEquipmentDGS120 Old Series

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

mode. Press to advance the Month in the DATE

mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance Date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the Schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to alter the Load status and/or to

Override scheduled event.

MODE: Press to advance to next mode without

affecting the scheduled memory information.

Sequence is: RUN, CLK, DATE, schedule SET. In

the SET mode, unit automatically reverts to the

RUN mode if no entries are made for 5 minutes.

SP DAY: Press during RUN mode to execute the

“SPECIAL DAY” schedule everyday. LCD will display

D in upper right corner. Pressing SP DAY again will

toggle the unit back to normal 7 day program opera-

tion.

ON/OFF: Pressing each time will select ON or OFF

event. Multiple OFFs may be scheduled to cancel

override ON’s.

ENTER: Press to store the displayed information into

memory. Information will not be stored until

ENTER is pressed.

NOTE: During settings, each press of the key will

advance one number. For rapid advance, hold key in.

DAY

MONTH

HOUR

DATE

MIN

YEAR

OVER-

RIDE

MODE

DAY

ON/

OFF

ENTER

TORK DG100 / DG120

DIGITAL TIME SWITCH

SEVEN DAY

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel controller

7 day scheduling

Special day scheduling

32 set points

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual override to the next scheduled event

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

Summary of content (8 pages)

PAGE 1
TORK DG100 / DG120 DIGITAL TIME SWITCH SEVEN DAY DAY MONTH HOUR DATE MIN YEAR OVERRIDE MODE SP DAY ON/ OFF ENTER READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT FEATURES Single channel controller 7 day scheduling Special day scheduling 32 set points Battery back-up uses standard 9 volt non-rechargeable (not supplied).
PAGE 2
TORK DG100 / DG120 DIGITAL TIME SWITCH SEVEN DAY DAY MONTH HOUR DATE MIN YEAR OVERRIDE MODE SP DAY ON/ OFF ENTER READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT FEATURES Single channel controller 7 day scheduling Special day scheduling 32 set points Battery back-up uses standard 9 volt non-rechargeable (not supplied).
PAGE 3
SETTING THE UNIT SELECT AM/PM OR 24 HOUR MILITARY FORMAT Upon powering up the unit the LCD will display the model number. The LCD will next display 12H which is an automatic (AM/PM) format. Press DAY/MONTH key to select today’s day. Press HOUR key to set present hour (check AM/PM). Press MIN key to set present minute. Press ENTER key. Unit now stores present time. Seconds are set to zero. DAYLIGHT SAVING The user may select either standard U.S. option or no daylight saving at all. 1. U.S.
PAGE 4
SETTING THE UNIT SELECT AM/PM OR 24 HOUR MILITARY FORMAT Upon powering up the unit the LCD will display the model number. The LCD will next display 12H which is an automatic (AM/PM) format. Press DAY/MONTH key to select today’s day. Press HOUR key to set present hour (check AM/PM). Press MIN key to set present minute. Press ENTER key. Unit now stores present time. Seconds are set to zero. DAYLIGHT SAVING The user may select either standard U.S. option or no daylight saving at all. 1. U.S.
PAGE 5
TO SET SCHEDULE SPECIAL DAY (HOLIDAY) For convenience, write out your desired schedule on a separate piece of paper. If display does not show SET then press MODE key until display shows SET. The display will show --:-- 01, with the “01” signifying first entry for ON or OFF. To execute this schedule at any time, simply press the SP DAY key while the unit is in the RUN mode.
PAGE 6
TO SET SCHEDULE SPECIAL DAY (HOLIDAY) For convenience, write out your desired schedule on a separate piece of paper. If display does not show SET then press MODE key until display shows SET. The display will show --:-- 01, with the “01” signifying first entry for ON or OFF. To execute this schedule at any time, simply press the SP DAY key while the unit is in the RUN mode.
PAGE 7
DELETE: If you choose to delete a schedule, simply modify the HOURS and MINUTES, until the time display reads --:--. This will occur after scrolling past 11 P.M. with the HOUR key and “59” with the MIN key. Then press ENTER to delete the event. OVERRIDE In order to temporarily change the current ON or OFF status of a load, simply press the override key. This can only be done when the unit is in the RUN mode. The load status will flash indicating that this is a change from a scheduled event.
PAGE 8
DELETE: If you choose to delete a schedule, simply modify the HOURS and MINUTES, until the time display reads --:--. This will occur after scrolling past 11 P.M. with the HOUR key and “59” with the MIN key. Then press ENTER to delete the event. OVERRIDE In order to temporarily change the current ON or OFF status of a load, simply press the override key. This can only be done when the unit is in the RUN mode. The load status will flash indicating that this is a change from a scheduled event.