BE Sport4 Bluetooth In Ear Headphones User Manual Regulatory model name APBESPORTH Version V1.
Contents Contents ................................................................................................................. 2 WHAT’S IN THE BOX ............................................................................................... 3 BE Sport4 EARPHONES ........................................................................................... 4 The BASICS ............................................................................................................. 5 Charging Your BE Sport4 .
WHAT’S IN THE BOX BE Sport4 earphones (with inline controller and microphone) Silicon tips (in L/M/S) Total of 3 pairs ear tips SpinFit TwinBlade tips (1 pair) Stabilizers (in L/M/S) 3 colors, total of 9 pairs Cable loop for adjusting the length of cable Pouch Charging cable (Micro-USB) Basic user’s manual Safety Instruction 3
BE Sport4 EARPHONES 1. 2. 3. 4. 5. 6.
The BASICS Charging Your BE Sport4 Although your BE Sport4 in-ear headphones come with a partially charged battery, it is recommended that you fully charge your BE Sport4 before first use. 1. Open the charge port cover on the in line controller. 2. The charge cable should be connected to the charge port and either to a PC or a dedicated USB charger, only while dry and clean. 3. When charging, the LED indicator is red. 4. LED Indicator turns blue once charging is complete. 5.
Checking Battery Level You can check the battery level of your BE Sport4 with the LED indicator To check battery level: 1. Press the Power/Function, volume up, and volume down buttons simultaneously while Bluetooth connected. 2. The LED indicator will flash red and blue.
Bluetooth Pairing 1 2 3 Using your BE Sport4 for first time Pairing BE Sport4 with source device 1. Press and hold the BE Sport4’s Power/Function button for 4 seconds until the LED indicator light flashes blue/red. Your BE Sport4 is now in pairing mode. 2. Turn on Bluetooth® on your source device, then select “BE Sport4” once it appears on the device list. NOTE: Consult your source device’s user manual for instructions on activating Bluetooth. 3.
power off after 3 minutes. C. Your BE Sport4 can store pairing information for up to eight devices. To pair additional devices to your BE Sport4 ensure that your BE Sport4 is not concurrently connected to any device, then repeat the steps 1,2,3 outlined above. In case where your BE Sport4 have already stored pairing information for eight devices and a ninth device is paired, the stored information for the very first device will be deleted.
Wearing Your BE Sport4 To ensure a secure and comfortable fit when wearing your BE Sport4: 1. Install the stabilizers on the BE Sport4 after removing the ear tips already placed on the boxed new set.* 2. Select right size of ear tips and install tips on BE Sport4. 3. Rotate the stabilizers and place the BE Sport4 into each ear so that they are positioned comfortably.
Handling Phone Calls When your BE Sport4 are connected to a Bluetooth-enabled smartphone you can handle your phone calls directly using your BE Sport4 in ear headphones.
Pairing with a Laptop The connection instructions below apply to owners of Windows 7, 8, 8.1 and 10. 1. Power your PC/Laptop 2. Find “Bluetooth Settings” 3. Switch your laptop Bluetooth to “On” 4. Turn the BE Sport4 to “Pairing Mode” 5. When the BE Sport4 is discovered by your laptop left click on “Pair” 6. Right click on the speaker symbol at the bottom right side of the screen 7. From the dropdown menu right click on the “Playback Device” 8.
Pairing with a Mac The connection instructions below apply to owners of all current and recent iOS versions 1. Power your Mac 2. Open “System Preferences” 3. Click on the Bluetooth symbol 4. Turn the BE Sport4 to “Pairing Mode” 5. When the BE Sport4 is discovered by your Mac click on “Pair” 6.
MISCELLANEOUS Multipoint Connections If you have stored pairing information for multiple devices and more than one of those devices have Bluetooth enabled at the same time, your BE Sport4 will enable multipoint connection. Multipoint connection allows your BE Sport4 to hold connections with two devices at the same time while playing audio signal from only one of the two devices.
• • Immersing the headset in water Operating the headset outside the recommended temperature range, or in extremely humid conditions • Dropping the headset or any other actions that cause the headset to take impact • Disassembling the headset, including the disassembling of screws • Not properly covering the USB charging port, causing water or other foreign particles to enter the headset Types of liquids covered by the water resistance rating: The water resistance rating only applies to fresh water and t
body of the headset. If the headset is not wiped after being worn during a workout, the salt from the sweat may negatively impact the lifespan of the headset. Therefore, we recommend that you use a clean cotton cloth to wipe the headset after your workout, in order to keep the headset clean.
Bluetooth Connectivity Bluetooth is a short-range wireless technology. Its connection quality may be interfered with metals, walls, and devices including but not limited to microwave ovens. At the same time, Bluetooth’s 2.4 GHz frequency is also shared by some Wi-Fi connections, which may result in a slower connection. This technical problem cannot be completely eliminated despite Bluetooth’s status as an international standard.
1 Ensure that your BE Sport4 are not connected to any device. 2 Put the BE Sport4 in pairing mode. 3 Press simultaneously the Power/Function, Volume Up, and Volume Down buttons for 2 seconds until the LED indicator flashes red five times and you hear five short tones from the BE Sport4. Because all pairing information is deleted after restoring factory settings, the BE Sport4 will directly enter pairing mode once powered on.
Federal Communication Commission Interference Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
CE Max RF power BT BR+EDR(2402-2480MHz): 4.0dBm RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=0 cm between the device and the human body. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Excessive sound pressure from earphones and headphones can cause hearing loss. Regulatory Conformance Hereby, Optoma Corporation.
NCC 依據低功率電波輻射性電機管理辦法 第十二條 ※經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不 得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 ※低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾 現象時,應立即停用,並改善至無干擾時方得繼續使用。 -前項合法通信,指依電信法規定作業之無線電通信。 -低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設 備之干擾。 Administrative Regulations on Low Power Radio Waves Radiated Devices warning: Article 12 Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved lo
Specification Connection type Bluetooth type Bluetooth 2.4GHz V4.1 Bluetooth profile HSP 1.2, HFP 1.6, A2DP 1.2, AVRCP 1.4 A2DP Codec SBC, Qualcomm® aptX™ audio, AAC Cable length 580 mm Driver Type Dynamic Driver size 6 mm Impedance 32 Ω Battery life (estimated) Battery type Microphone sensitivity Up to 10 hours Lithium-ion battery, Cylindrical Type, Typical 3.
www.optoma.