AXIS 2 CD Player with ANTI-SHOCK™ MANUAL ©2001 Industries http://www.numark.
AXIS 2 SAFETY INSTRUCTIONS a) Read Instructions - All the safety and operating instructions should be read before this product is connected and used. b) Retain Instructions - The safety and operating instructions should be kept for future reference. c) Heed Warnings - All warnings on this product and in these operating instructions should be followed. d) Follow Instructions - All operating and other instructions should be followed. e) Placement – place the unit in a clean dry location.
AXIS 2 ® AXIS 2 PROFESSIONAL TABLETOP CD PLAYER CONGRATULATIONS... You have just purchased a CD player designed specifically for the professional DJ. This unit has been designed to provide CD mixing with the same ease and creativity that you have enjoyed with records. Please take a few moments to familiarize yourself with the AXIS 2 by reading the following information before attempting to operate the unit.
AXIS 2 TABLE OF CONTENTS Safety Instructions 2 Introduction and Registration 3 Set-up & Connections 5 Description of the Features Top Panel Front Panel Rear Panel Display 6 8 8 9 Basic Operation Play, Pause and Cue Operations Matching the Tempo Beat Matching Using Pitch Bend Relay and Fader Start 10 11 11 12 Example of Mixing 13 Before Switching off the Power 14 Troubleshooting Guide 14 Information and Specifications 15 Warranty 16 - The Leader in DJ Technology ©2001 Numark Industries
AXIS 2 SETUP and CONNECTIONS Typical connection with a mixer is illustrated below. 1. Find a level surface free of excessive vibration to place your equipment 2. Connect the line output connections using the supplied audio cable from the CD Player to the line inputs of your mixer. 3. Connect Fader start cable. Attach your CD play to a similarly equipped DJ mixer. (This connection can also be used with a remote switch) 4. If setting up 2 units, you can connect a relay cable between the units.
AXIS 2 TOP PANEL FEATURES - The Leader in DJ Technology ©2001 Numark Industries -6- http://www.numark.
AXIS 2 1. Open/Close: Press to load or eject the disc. The tray will not open if a disc is in play. The tray door will automatic close in 30 seconds if left open. This is to protect the tray from accidental damage while open 2. Single: toggles the unit to play back just one track at a time (single) or play continuously through all tracks and then start over repeating the CD infinitely (continuous). 3.
AXIS 2 FRONT PANEL 16. CD Illumination Light – lights up the CD drawer and CD when open. 17. CD Drawer – Place your CDs you wish to play in here. This unit is designed to play commercially available CD and properly burned and finalized CDR and CDRW formats. Due to variances on the specification of certain CD burners and CDs some discs home made CDs may not play properly. REAR PANEL 18. Power Switch- Turn on and turn off the machine with this button.
AXIS 2 DISPLAY FEATURES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. CUE - Flashing when the unit is setting a cue point. Lit continuously when the unit is paused at a cue point. PAUSE (II)- Active when the unit is paused. PLAY (>)- Active while the unit is actually playing a CD. TRACK - Shows the track that the unit is playing. TOTAL – indicates when total CD remaining tracks are displayed. MINUTES - Shows the minutes elapsed or remaining depending on mode setting.
AXIS 2 DESCRIPTION OF THE PLAY/PAUSE AND CUE OPERATIONS PLAY and CUE Pressing the “PLAY/PAUSE” button starts the disc. Pressing the “CUE” button will reset the disc to the last place where the disc was started. This is called the cue point. By alternately pressing the “PLAY/PAUSE” button and the “CUE” button, the disc may be returned and played from the cue point any number of times. This function is called back cue.
AXIS 2 RELAY PLAY This mode will be operational only when 2 units are connected via the supplied relay cable. 1. Insert CDs into both of the units. 2. Press the “RELAY” button on both units to activate. 3. We recommend putting both sides in SINGLE play mode while learning this function. 4. Press play on the first unit. When that unit has finished play it will send a signal to the second unit to start play.
AXIS 2 MATCHING THE BEATS PER MINUTE (BPM) Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear and adjusting the pitch. When the tempo of the music of the selected CD player is slow compared to the tempo of the other player, move the slider to the “+” side and match the tempo. When faster, move the pitch slider to the “-“ side. The following description is for the case of matching the pitch of PLAYER 2 to the pitch of the music being played on PLAYER 1.
AXIS 2 EXAMPLE OF MIXING USING TWO CD PLAYERS While playing a disc on PLAYER 1 load a disc into PLAYER 2 and select your next track, match its pitch to the track playing on PLAYER1 and when you are ready use the crossfader on your mixer to fade from PLAYER 1 to PLAYER 2. PLAYER 1 PLAYER 1 PLAYER 1 Load a disc and press the OPEN/CLOSE button. Select the track to be played. Press the PLAY button PLAYER 2 PLAYER 2 PLAYER 2 Load a disc and press the OPEN/CLOSE button. Select the track to be played.
AXIS 2 BEFORE SWITCHING OFF THE POWER: When you have finished using the CD player, be sure that the disc tray is closed with the “OPEN/CLOSE” button before switching off the power. Switch off the power after the disc holder has been closed with the “OPEN/CLOSE” button DO NOT switch off the power when the disc holder is open.
AXIS 2 SPECIFICATIONS TECHNICAL Disc Type Time Display Quantization Oversampling rate Sampling Frequency Frequency response T.H.D. + NOISE S/N ratio (IHF-A) Dynamic range Output level Start Time Pitch control range Pitch bend Digital Output Standard Compact discs (12 cm & 8 cm) Track Elapsed, Track Remain, or Total remain 1 bit linear/Channel, 3 Beam Laser 8 Times 44.1 kHz 20 Hz to 20 kHz Less Than 0.005% > 96 dB > 94 dB 1.9 Volts R.M.S. within 0.
® Professional Disc Jockey Products LIMITED PRODUCT WARRANTY 1. 2. 3. 4. 5. 6.