Professional Disc Jockey Products DM1295 PROFESSIONAL DJ SAMPLING MIXER Owner’s Manual ©2000 Industries http://www.numark.
DM1295 Safety Information h) Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. i) Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.
DM1295 DM1295 PROFESSIONAL DJ MIXER with onboard sampler CONGRATULATIONS! You have purchased the DM1295 stereo preamp mixer with onboard sampler. Numark’s engineers have designed this mixer to accommodate both the mobile DJ market and the professional installation market. The DM1295 provides the end user with high-end audio circuitry combined with maximum versatility to meet the demands of every intended situation.
DM1295 MIXER FEATURES 22 23 21 19 20 INPUTS 1. Input Toggle Switches - select which source will be live to that channel based on what you have connected to the rear panel input section. 8. Treble and Bass Controls – for fine-tuning the tone of your voice through the sound system. The controls are detented for setting tone "flat". 2. Input faders - control individual source levels in the mix. 9. DJ Mic Gain Control – for volume adjustment of the Neutrik™ “Combo” connector on the faceplate.
DM1295 HEADPHONE CUEING EQUALIZER SECTION 16. 6-Band Stereo Graphic Equalizer (EQ). EQ compensates for differences in source material sound quality. In ultra-compact mobile systems this EQ can be used to tailor the sound to the acoustical requirements of the room. Center frequencies are 42Hz, 152Hz, 480Hz, 1.5kHz, 4.8kHz and 15.4kHz. Faders have a center detent for an accurate "flat” response. Below is a typical "house" EQ curve. Notice how the knobs above "0" balance out the knobs below.
DM1295 - The Leader in DJ Technology ©2000 Industries -6- http://www.numark.
DM1295 SAMPLER OPERATION 2 1 3 4 5 6 This sampler was designed for ease of use and understanding. It can retain in memory up to 110 seconds worth of sampling. Each bank can save 27.5 seconds for playback even after the unit is shut down. It’s as simple as (1) pressing a channel send (2) recording the sample (3) playing it back. Enjoy a whole new way to sample. 1. 2. 3. 4. 5. 6. Output Gain Control – adjusts the volume of the sampler. Pitch Adjust – changes the playback pitch of the sample.
DM1295 REAR PANEL FEATURES 1. 2. 3. 4. 5. 6. 7. Power Connector. Plug in power cord here and check the voltage level to match your country’s standard. GND is the grounding lug for turntables 1, 2 and 3 (phono inputs on Channels 1, 2 and 3). Always use this connection (your turntable cable should have a grounding wire). The Stereo Main Outputs are low-impedance RCA connectors controlled by the Master fader.
DM1295 QUICK SETUP DIAGRAM VERY IMPORTANT: Please read this entire manual before connecting this unit to your system For optimum performance: • • • • Always make sure that AC power is OFF while making any connections. Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over 50ft/14m) Be sure plugs and jacks are tightly mated. Loose connections can cause hum, noise or intermittence that could easily damage your speakers.
DM1295 SPECIFICATIONS INPUTS: Line: Mic: Phono: 10Kohm input impedance 110mV rms sensitivity (for 1.22V output) 10Kohm input impedance unbalanced 1.6 mV rms sensitivity (for 1.22V output) 500mV rms max input Talkover attenuation: variable from no cut to -16 dB 47Kohm input impedance 1.8mV rms sensitivity @ 1 KHz (for 1.22V output) OUTPUTS: Line: 9V rms max Headphone Amp: 1V rms watt into 16ohm Distortion: less than 0.01% SIGNAL TO NOISE RATIOS* (vs.
DM1295 BLOCK DIAGRAM - The Leader in DJ Technology ©2000 Industries - 11 - http://www.numark.
Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long? 1.
