Professional Disc Jockey Products DM3001X DJ MIXER Owner’s Manual ©2001 Industries http://www.numark.
DM3001X h) Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. i) Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.
DM3001X VERY IMPORTANT Please read this entire manual before connecting this unit to your system For optimum performance: • • • • • • • • • The crossfader is a user replaceable item and subject to wear. Excessive force can wear out the fader quickly. This is not a warranted item. Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this will void your warranty. In normal use slide controls can last for many years.
DM3001X DM3001X PROFESSIONAL DJ MIXER CONGRATULATIONS! You have purchased the DM3001X Stereo Mixer by . This mixer was developed by DJs for you combining requested features in an easy to understand layout. Using the latest in circuit design technology and our history of award winning development experience you can expect years of reliable service from this product. Careful attention to detail was provided in this unit. The DM3001X even has smooth edges to ensure your fingers don’t get caught up in the mix.
DM3001X TABLE OF CONTENTS Safety Measures 2 Important Information 3 Registration 3 Introduction 4 Description of the Features 6 Quick Setup Diagram 9 Block Diagram 10 Specifications 11 Warranty 12 - The Leader in DJ Technology ©2001 Industries -5- http://www.numark.
DM3001X 25 24 15 9 3 14 16 6 10 4 5 11 8 12 2 1 23 22 21 17 20 18 7 13 19 - The Leader in DJ Technology ©2001 Industries -6- http://www.numark.
DM3001X MIXER FEATURES INPUTS CROSSFADER 1. Input faders - control individual source levels in the mix. 17. 2. Input Toggle Switch (Transform) - selects which source will be live to that channel based on what you have connected to the rear panel input section. By removing the face panel the switch can be rotated into any of eight positions. Crossfader - achieves clean segues between the two input channels selected by the Crossfader Assign. 18.
DM3001X REAR PANEL FEATURES 4 5 2 1 10 9 8 6 3 6 3 7 1. Power Input - to plug your power plug in before switching on power. See safety precautions on page 3 for proper treatment of power. 2. Voltage Selector – Set this to the appropriate power for your location. If unsure ask your authorized dealer. 3. Phono Inputs – plug your turntables in here. 4. Ground lug - use these connections with your turntables’ grounding cable to avoid signal hum. 5.
DM3001X QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on.
DM3001X BLOCK DIAGRAM - The Leader in DJ Technology ©2001 Industries - 10 - http://www.numark.
DM3001X SPECIFICATIONS Inputs: Line: Mic: Phono: 10K ohm input impedance 83mV rms sensitivity for 1.22V output 600 ohm input impedance unbalanced 1mV rms sensitivity for 1.22V output 65mV rms max input 47Kohm input impedance 1.3mV rms sensitivity @ 1KHz for 1.22V output Outputs: Line: Headphone: 9V rms max 0.5W into 47ohm Distortion: less than 0.
Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long? 1.
