® Professional Disc Jockey Products PRO TT-1 PROFESSIONAL DIRECT DRIVE TURNTABLE OWNER’S MANUAL INDUSTRIES 11 Helmsman Avenue, North Kingstown, RI 02852 ©1999 http://www.numark.
PRO TT-1 Safety Information and Product Registration 7. Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
PRO TT-1 PRO TT-1 Professional Turntable INDEX Safety Information Product Registration Page 2 System Precautions Page 4 Introduction Page 5 Features and Assembly Instructions Page 6 Operating Instructions Routine Maintenance Page 10 Specifications Page 11 Warranty and Service Page 12 Contents of this package Please check outer packing material for hidden parts 1. Main Unit 2. Turntable platter 3. Rubber mat 4. Slip mat 5. Dust cover 6. 45-rpm adaptor 7. Counterweight 8. Headshell 8.
PRO TT-1 IMPORTANT INFORMATION... Please read this entire manual before connecting the PRO TT-1 to your system. For optimum performance: GENERAL SYSTEM PRECAUTIONS • Always make sure that AC power is OFF while making any connections. • Use appropriate cables throughout your system: Quality shielded audio cables and terminated shielded video cables, low-capacitance preferred. Speaker cables must be 14-gauge minimum; 12- or 10-gauge is better.
PRO TT-1 CONGRATULATIONS! You are now the owner a PRO TT-1 Professional Turntable, the ultimate tool for todays skilled turntablist. This unit has been designed by DJs for DJs. With it’s super high-torque platter and large back lit display the PRO TT-1 gives the professional absolute total control.
PRO TT-1 FEATURES,OPERATING, & ASSEMBLY INSTRUCTIONS... 9 11 10 8 12 7 6 14 5 13 4 17 1 15 2 16 3 To fully appreciate the features of the P R O T T - 1, please read this entire manual before you begin operation. The PRO TT-1 should be placed on a level sturdy surface. Keep in mind that there are a few features you may never have seen before on a turntable of this type that you will need to read about to use properly. Start by removing all parts from the package and place on a level surface.
PRO TT-1 8. 45 Adapter - Place on Center Spindle (7) for playing 7” records with large center holes. 9. Forward/Reverse Buttons - These determine the direction the platter will spin. 14. Quartz Lock On - will hold the revolution speed at exactly the specified speed (3) Off - will allow use of the Pitch Adjust (13) 15. LCD Display - Explained in Display Section 10. Lid Hinge Holder - Place the bottom tabs of your lid hinges in here after you finish assembly. 16.
PRO TT-1 27. Anti-Skate Control - This applies inward force to the tonearm so it doesn’t skip outward across the record due to the centrifugal force of the record spinning. Cartridge manufacturers usually specify the proper setting of this. (3) Release the arm clamp and lift the tonearm from the arm rest so it moves freely. (4) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely). 28.
PRO TT-1 REAR PANEL DIAGRAM... 42 41 43 40 45 47 44 46 40. Removable Lid - Protects the turntable from dirt and dust. 41. Hinge Assembly - Holds the lid and turntable together. Attach now by sliding the bottom tabs of the Hinge Assembly into the Hinge Holders (10). 42. Platter Speed Output - This output is to be used with external devices the require platter speed information. 43. Remote Start/Stop - This is used with external control devices.
PRO TT-1 GENERAL OPERATING INSTRUCTIONS... 1. Turn the power dial to turn on, the speed indicator and the strobe-illuminator will light up. 2. Turn on and raise the target light for illuminating the stylus tip by pushing the target light button. 3. Place a record on the turntable mat, when playing a 45rpm record with a large center hole, place the 45-rpm adaptor on the center spindle. 4. Set the rotation speed (33/45/78) to match the record. 5. Release the arm clamp. 6.
PRO TT-1 SPECIFICATIONS... TURNTABLE SECTION Type Driving method Motor Turntable platter Turntable speed Pitch Variance Starting Torque Braking 3-speed, full manual Direct drive 12 Pole, 3 Phase, Brushless DC Motor Aluminum diecast 330mm dia. 33-l/3 , 45, and 78 rpm ±10% more than 2.2kgf.cm Electronic OUTPUT Wow and flutter S/N ratio Output Difference Output Level Channel Separation Pitch 0.13% 50dB (DIN-B) 2.3dB 1.7 - 3.
® LIMITED PRODUCT WARRANTY 1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ mixers and amplifiers are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the following period of time after that date for (2) Years.
