Use and Care Manual

ManualsBrandsNuMax ManualsAir Compressors, Tools & Accessories1-3/4 in. 18-Gauge L-Cleat Dual Handle Flooring Nailer

HTTP://WWW.NUMAXTOOLS.COM

1-888-669-5672

PRIME GLOBAL PRODUCTS, INC.

MODEL: S18GLCNDH

HTTP://WWW.NUMAXTOOLS.COM

1-888-669-5672

PRIME GLOBAL PRODUCTS, INC.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

WARNING:

Failure to follow warnings could result in DEATH OR SERIOUS INJURY.

S18GLCNDH-V1 03/19

18 GAUGE L CLEAT FLOORING NAILER18 GAUGE L CLEAT FLOORING NAILER18 GAUGE L CLEAT FLOORING NAILER

Summary of content (9 pages)

PAGE 1
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 PRIME GLOBAL PRODUCTS, INC. MODEL: S18GLCNDH 18 GAUGE L CLEAT FLOORING NAILER HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 PRIME GLOBAL PRODUCTS, INC. WARNING: Failure to follow warnings could result in DEATH OR SERIOUS INJURY. SAVE THIS MANUAL FOR FUTURE REFERENCE.
PAGE 2
MODEL: S18GLCNDH MODEL: S18GLCNDH GENERAL SAFETY RULES P3 SYMBOLS UNPACKING P5 FEATURES P6 ● The following signal words and meanings are intended to explain the levels of risk associated with this tool, and can be found in the manual, packaging, labeling, and all other information provided with this tool: SYMBOLS OPERATION PREPARE THE TOOL P6 LOADING L CLEATS P7 UNLOADING L CLEATS P8 CHANGING THE FOOT PLATE P8 ADJUSTING THE FRONT FOOT P9 SETTING THE AIR PRESSURE P9 OPERATING THE TOOL
PAGE 3
MODEL: S18GLCNDH M a k e s u re t h e h o s e i s f re e o f obstructions or snags. Entangled or snarled hoses can cause loss of balance or footing and may become damaged, resulting in possible injury. Wash hands after handling. This product or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. TOOL USE AND CARE ● Know this tool.
PAGE 4
MODEL: S18GLCNDH MODEL: S18GLCNDH FEATURES OPERATION SPECIFICATIONS PREPARE THE TOOL AIR CONSUMPTION: 5.3 SCFM with 100 fasteners per minute @ 90 psi AIR INLET: 1/4 inch NPT MAGAZINE CAPACITY: 120 pcs WEIGHT: 8.5 lbs MAXIMUM PRESSURE: 115 psi PRESSURE RANGE: 70 psi – 115 psi FASTENER SIZE RANGE: The tool is shipped with the Arm (A) part detached from the main body part. Follow these instructions to prepare the tool for use. 1. Set the Arm(A) against the Handle . 2.
PAGE 5
MODEL: S18GLCNDH ! WARNING: The tool may fire when it is first connected to the air source. Always connect the tool to the air source before loading fasteners to prevent injury from unintended cycling. Always make sure the tool's magazine is empty at the beginning of each work session, before connecting to an air source. ! WARNING: Only use those fasteners recommended for use with this tool.
PAGE 6
MODEL: S18GLCNDH MODEL: S18GLCNDH Figure 5 ! WARNING: ! WARNING: Make sure there is no fastener in the magazine before clearing a jam. An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece.
PAGE 7
MODEL: S18GLCNDH MODEL: S18GLCNDH oi l COLD WEATHER OPERATION For cold weather operation, near and below freezing, the moisture in the air line may freeze and prevent tool operation. We recommend the use of air tool lubricant or permanent antifreeze (ethylene glycol) as a cold weather lubricant. ! WARNING: CAUTION: The air compressor must be able to maintain a minimum of 70 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving.
PAGE 8
MODEL: S18GLCNDH MODEL: S18GLCNDH TROUBLESHOOTING ! WARNING: ! WARNING: Stop using tool immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a qualified service person or an authorized service center. PROBLEMS Driving blade does not retract. Driving blade retracts slowly. Nail is not countersunk. Nailer leaks air. POSSIBLE CAUSES 1. Zero or Low air pressure. 1. Check air supply for 70 psi minimum to115 psi maximum.
PAGE 9
MODEL: S18GLCNDH MODEL: S18GLCNDH THESE WARRANTIES ARE SUBJECT TO CHANGE WITHOUT NOTICE. 16 HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672 HTTP://WWW.NUMAXTOOLS.