Use and Care Manual

●
●
●
●
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure
no breakage or damage occurred during
shipping.
Do not discard the packing material until
you have carefully inspected and
satisfactorily operated the tool.
If any parts are damaged or missing,
please call 1-888-669-5672.
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result
in possible serious personal injury.
WARNING:
!
WARNING:
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse
and could result in hazardous
condition leading to possible serious
personal injury.
Such precautionary measures reduce the risk
of injury to persons.
LOADINGTOOL
Do not load the tool with fasteners
when any one of the operating controls
is activated.
Never place a hand or any part of body
in fastener discharge area of tool.
Never point the tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental
actuation may occur, possibly causing
injury.
●
●
●
●
!
The warnings and precautions
discussed above cannot cover all
possible conditions and situations that
may occur. It must be understood by
the user that common sense and
caution are factors which cannot be
built into this product, but must be
supplied by the user.
WARNING:
●
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
HTTP://WWW.NUMAXTOOLS.COM 1-888-669-5672
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool
allows users to direct the exhaust according to
operator preference. To adjust the direction,
turn the exhaust cap in the desired direction.
OPERATION
FEATURES
●
●
●
●
FEATURES
SPECIFICATIONS
360 ° ADJUSTABLE EXHAUST
Allows user to direct air away from face.
COMFORT-GRIP HANDLE
For increased comfort and control.
WITH RELOAD INDICATOR
Visible nail level.
ADJUSTABLE DEPTH
Depth is easily adjustable for various
applications.
AIR CONSUMPTION:1.76 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY:
100 fasteners, 18 gauge
WEIGHT: 3.44 lbs
MAXIMUM PRESSURE: 110 psi
PRESSURE RANGE: 70 psi – 110 psi
FASTENERS RANGE:
Compatible with generic 18 gauge brad nails
and staples.
Brad nails: 5/8” to 1-9/16”
Staples:1/2” to 1-9/16”
1/4”(5.7mm)
15mm
5/8”
3/4”
1”
1-3/16”
1-1/4”
1-9/16”
20mm
25mm
30mm
32mm
40mm
0.079”(2mm)
13mm
1/2”
5/8”
3/4”
1”
1-1/4”
1-9/16”
16mm
19mm
25mm
32mm
40mm
The tool is packed with an additional nose
cover with which the nailer can be changed to
be regular brad nailer/stapler.
CHANGING THE NOSE COVER
Disconnect the tool from air source.
Remove fasteners from the tool. Failure to
do so will cause the fasteners to eject from
the front of the tool.
Pull up on the latch(A) and open the flooring
nose cover (B).
Remove the O-ring (C) and pin (D)
Remove the flooring nose cover(B).
Pull the regular nose cover (E) on the nose
of the nailer.
Put the pin (D) and O-ring (C) back.
Push the latch back to the nose cover on
the nailer's nose.
1.
2.
3.
4.
5.
6.
7.
8.
Latch(A)
Flooring nose cover(B)
O-Ring (C)
Pin(D)
Flooring
nose cover
(B)
Regular nose cover(E)
Put the pin(D) and
O-ring(C)back
MODEL: SFBC940 MODEL: SFBC940