professional series Owner’s Guide PROCOMP Deluxe Vehicle Security and Remote Start System with 900 Mhz 2 Way Confirming OLED Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2012 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control ............................................................... 3 Using the 2 Way Remote Control for the First Time ........................ 3 Arming the Security System ............................................................ 3 Bypassing the Shock Sensor .......................................................... 3 Disarming the Security System ........................................................ 4 Two Stage Door Unlock (optional) .........................
Using Your Remote Control Using the 2 Way Remote Control for the First Time. The 2 way remote control has been shipped in Battery Save Mode to conserve battery power and will be necessary for you to turn off battery save mode before using the remote for normal operation. It is also recommended that you fully charge the battery before use. Refer to the additional 2 way remote control features section of this manual for details.
Disarming the Security System To disarm the system press the button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected). NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle. Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door.
Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the seconds will open the vehicle’s trunk or hatch. button for 3 Activating Optional AUX 1 (Optional) This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system. 1 Way Transmitter - Press and hold 2 Way Transmitter - Press and hold for 3 seconds. + for 3 seconds.
Valet Mode To engage valet mode: 1. Turn the ignition key to the ON position. 2. Press and hold the valet button for 5 seconds. 3. The LED will light solid indicating that the system is in valet mode. When valet mode is activated the status LED will light solid, and all security functions will be disabled. To disengage valet mode: 1. Turn the ignition key to the ON position. 2. Press and release the valet button. 3. The LED will turn off indicating that the system has exited valet mode.
Coded Emergency Override Procedure: The system has an optional override mode that allows you to program a 2 digit personal code using the emergency override button offering a higher level of security. This feature must be enabled by your installing dealer, the default override code is 11. 1. Enter the vehicle (the security system will trigger). 2. Turn the ignition switch to the ON position. 3.
Using Your Remote Vehicle Starter Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds.
Turbo Timer This option will keep the engine running to allow the vehicle’s turbo to properly cool down before shutting the engine off. To engage the turbo timer feature: 1. With the vehicle running via the ignition key and your foot off of the brake pedal. 2. Engage the vehicle’s parking brake and press the valet button 2 times. 3. The vehicle’s parking lights will turn on to verify the Turbo Timer feature has been activated. 4.
Operating the 2 / 4 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs.
Manual Transmission Mode Remote starting a vehicle equipped with a manual transmission will require a 2 step safety sequence, Enter Ready Mode and Activate Ready Mode. The steps for entering and activating ready mode are programmable, see your installing dealer for details. 1 - Manual Transmission - Enter Ready Mode: Manual transmission enter ready mode is step 1 of 2 required to allow remote start activation. Perform 1 of the following steps to Enter Ready Mode.
Remote Start Valet Mode Remote Start Valet Mode is used to disable the system from remote starting. To enter or exit remote start valet mode simply follow the 4 steps outlined below: 1. Push and hold the programming/valet button. 2. Cycle the ignition ON/OFF, ON/OFF, ON/OFF. 3. Release the programming/valet button. 4.
Additional 2 Way OLED Remote Control Feature Descriptions The following features / menus are activated through the 2 way remote control’s additional advanced level menus, refer to the activating 2 way remote control features section of this manual. AUX Menu Controls the 4 optional auxiliary outputs Battery Save Mode While in Battery Save Mode the 2 way remote control will NOT look for any incoming signals from the main unit until battery save mode is turned off.
Fahrenheit / Celsius Display the current temperature in Fahrenheit or Celsius. Clock Set Adjust the clock displayed on the screen. Alarm Tones Selectable tones used for the alarm clock feature. Remote Start Tones Selectable tones used to indicate remote start activation. Remote Start Shutdown Tones Selectable tones used to indicate remote start has shutdown. Page Call Out With the ignition OFF, press the valet button for 2 seconds, the 2 way remote will sound the paging tone and display CALL on the screen.
Activating 1 Way Remote Control Features Basic Remote Control Functions Advanced Level 1 Remote Control Functions Press and release 2 times to access level 1 menu functions, the AUX LED will turn on solid. The menu will time out after 3 seconds on inactivity. 2012 Audiovox Electronics Corporation. All rights reserved.
Advanced Level 2 Remote Control Functions Press and release 3 times to access level 2 menu functions, the AUX and Siren LED will turn on solid. The menu will time out after 3 seconds on inactivity. Advanced Level 3 Remote Control Functions Press and release 4 times to access level 3 menu functions, the AUX, Siren and Lock LED will turn on solid. The menu will time out after 3 seconds on inactivity. When in 2 car mode, the LED will flash 2 times after activating a feature.
Activating 2 Way OLED Remote Control Features Basic Remote Control Functions 2 Way OLED Transmitter - Basic Functions Lock Lock Trunk Function Start / Aux Operation Method Press and Release x Unlock Headlight Unlock Press and Release x Press and Hold (3 Sec) x Trunk Press and Hold (3 Sec) x Car Finder x x Press and Release Panic x x Press and Hold (3 Sec) Remote Start x Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown x Press and Hold (3 Sec
Advanced Level 1 Remote Control Functions Press and release 2 times to access level 1 menu functions, AUX Controls will be displayed on the screen. The menu will time out after 10 seconds on inactivity.
Advanced Level 2 Remote Control Functions Press and release 3 times to access level 2 menu functions, System Controls will be displayed on the screen. The menu will time out after 10 seconds on inactivity.
Advanced Level 3 Remote Control Functions Press and release 4 times to access level 3 menu functions, Fuel Saver will be displayed on the screen. The menu will time out after 10 seconds on inactivity.
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 1 FLASH... PAUSE ZONE 1 TRIGGER, SHOCK 2 FLASH... PAUSE ZONE 2 TRIGGER, TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, IGNITION 5 FLASH...
Replacing Remote Control Batteries CAETX91 1 Way 6 Button Remote Control: The battery (model CR2032) inside each remote control should last approximately 1 year under normal use. When the battery becomes weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 2 side panels and 1 screw then disassemble the halves of the remote control. 2.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.