Model PRO9776E Owner’s Manual Table Of Contents: Features and Options Page 2 Arming The System-Active Page 3 - 4 Protection While Armed Page 4 Disarming Your System Page 5 While The System Is Sounding Page 5 Intrusion Signals and Tones Page 5 Valet Override, Programming and Safety Control Switch Page 6 Manually Overriding Your System Page 6 Programming Your Custom Override Code Page 6 - 7 Using The Custom Code Override Page 8 Eliminating The Normal Arm/Disarm Chirps Page 8 Remote Pani
5 Button Remote Start Security System With Plug-In Shock Sensor and Starter Disable FEATURES: 2 Five Button Programmable RF Transmitters Seven Channel Code Learning Receiver (capable of accepting 4 transmitters) Code Hopping Technology Selectable Manual Override Mode Remote Panic in All Modes Protected Push Button Valet/Override Switch In Windshield Receiver External Superheterodyne Receiver Antenna w/Push Button Switch & LED Selectable Automatic Timed Start Mode User Programmable Manual O
YOUR “SPREAD SPRECTUM" TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.
SILENT ARMING - ACTIVE (Feature must be activated during programming) During step 2 above, hold the transmitter button for 2 seconds then release. The unit will arm without the chirps for this one lock cycle. ARMING THE SYSTEM - PASSIVE (AUTOMATIC) (Must be activated during programming) 1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and trunk lid. The dash mounted LED begins to flash rapidly, indicating 30 second passive arming has begun. 2.
Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. Note: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. DISARMING THE SYSTEM As you approach the vehicle, press and release the Disarm button on the keychain transmitter.
from the vehicle. Upon disarm, the siren will chirp 4 times and the parking lights will flash 3 times. Enter the vehicle and before turning on the ignition switch, observe the LED flash pattern. If the LED flashes one time...pause, one time...pause etc., then an intrusion attempt was made by impact or a strong vibration that the shock sensor detected. Check the vehicle for possible damage to the glass or body panels. If the LED flashes two times...pause, two times...pause etc.
Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 9 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following: 1.
. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. You will notice the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates that the code has not been changed.
for use in emergency situations. To use remote panic, 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the Lock or Unlock button is pressed and released, the Panic mode will be turned off immediately.
With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or release the parking brake, or activate the transmitter's start button two times in succession.
OPERATING ON AUTOMATIC START UP TIMER MODE This unit has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING ! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device.
ADDITIONAL REMOTE FUNCTION (CHANNEL 4) This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Can Be Set Up To Activate Rear Window Defogger During Remote Start If Vehicle Is So Equipped Remote Window Closure Rear Hatch Release Right Or Left Slider Doors in An Equipped Van To activate the optional accessory, press the option button on the keychain transmitter.
TELEMATIC UPGRADE: This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that can give you control of certain functions of your vehicle from a telephone or in some cases a computer interface. Please check with your installation center for most recent Telematic Upgrades.
Note: Certain systems have the ability to utilize channels 6 and 7 for driver priority programming. For driver priority, the vehicle must be equipped with this feature, and the optional feature must be set up and installed by your installation center. Once this feature is added when the unlock button of transmitter 1 is used, it will set driver 1 priority and when the unlock button of transmitter 2 is used it will set driver 2 priority.
PRO9776E SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH... PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...
NOTES © 2014 Voxx Electronics Corporation, Hauppauge, NY 11788 128-9307 Page 16 128-9307 16 of 16
