User's Manual

ManualsBrandsNutek ManualsElectronicsTransmitter

128-9486

Page 1

1 2

Lock Button

Press once to lock and arm alarm.

Press and hold 3 seconds for panic

alarm where applicable

Unlock Button

Press once to unlock and disarm alarm

Press and hold 3 seconds for panic

alarm where applicable.

Trunk / Start Button

Press two times in succession to

start vehicle. Press and hold for

3 seconds for Trunk Release where applicable

OPTION 1

Press and release to activate

option 1 where added

OPTION 2

Press and release to activate

option 2 where added

Model PR2LED

Operators Manual

RF Upgrade Kit

PATENTED: www.voxxintl.com/company/patents

Check with your installation center for features and functions operational on your system.

To Operate System:

1) Press the lock button to lock the doors and arm the alarm if installed. The LED alongside the

lock button will ash and the transmitter will beep once when the vehicle receives and responds

to the command.

2) Press the unlock button to unlock the doors and disarm the alarm if installed. The LED along-

side the unlock button will ash and the transmitter will beep twice when the vehicle receives and

responds to the command.

3) Press and hold the Trunk/Start button for 3 seconds to unlock the trunk. The LED alongside

the button will ash when the vehicle receives and responds to the command.

4) Press the Trunk/Start button two times in succession to start the vehicle a melody will sound

upon start. The vehicle will start and run the predetermined time set up during installation (5 to

60 minutes selectable). During this run cycle, the LED alongside the button will ash 1 time every

10 seconds indicating the vehicle is in fact running.

Anytime during the run cycle, enter the vehicle by rst unlocking the doors with your transmitter,

insert your key and turn it to the run, NOT START, position, then step on the brake, the vehicle is

now in control of the ignition key the transmitter will sound a shut down / owner take over melody.

NOTE: For push to start vehicles contact your installation center for proper procedure

Summary of content (8 pages)

PAGE 1
Model PR2LED Operators Manual RF Upgrade Kit Lock Button Press once to lock and arm alarm. Press and hold 3 seconds for panic alarm where applicable Unlock Button Press once to unlock and disarm alarm Press and hold 3 seconds for panic alarm where applicable. Trunk / Start Button Press two times in succession to start vehicle.
PAGE 2
Consult your installation center for operation and information on convenience options 1 & 2 which may have been connected or added to your vehicle. Quick Stop Mode: With vehicle running, if you wish to make a quick stop and leave the vehicle running, once you arrive at your destination: a) Place the gear selector in Park, b) Set the parking brake, c) With your foot OFF the brake, press the transmitter button two times in succession. The vehicle will now be under control of the remote start system.
PAGE 3
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the Receivers push-button switch from 1 up to 9 times. 5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on. 6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the Receivers push-button switch from 1 up to 9 times. 7. Finish by turning the ignition switch to the off position.
PAGE 4
2) Within 5 seconds, press and release the Receivers push-button switch 1 time. 3) Within 5 seconds, turn the ignition switch off then on. 4) Within 5 seconds, press and release the Receivers push-button switch 1 time. 5) Turn the ignition switch off then on and start the vehicle. NOTE: I f you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above.
PAGE 5
TO BEGIN THE AUTOMATIC START UP TIMER 1. Turn the ignition key on then off. 2. Within 10 seconds, activate the RF start command two times. (Push the programmed channel button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the preprogrammed time (5, to 60 minutes), and then shut off. This will continue for 48 hours.
PAGE 6
set up and installed by your installation center. Once this feature is added when the unlock button of transmitter 1 is used, it will set driver 1 priority and when the unlock button of transmitter 2 is used it will set driver 2 priority. In this situation, the unlock button can be programmed into two receiver channels, unlock, channel 2 and driver priority 6 or 7. In no other circumstance will the system allow a transmitter button to be programmed into 2 receiver channels at the same time.
PAGE 7
This Page Intentionally Left Blank Page 7 128-9486 Page 7
PAGE 8
To purchase replacement transmitters or to get additional product information go to: www.pursuitcarsecurity.com FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.