User's Manual

ManualsBrandsNutek ManualsElectronicsTransceiver

128-9456

Page 1

PRESTIGE

IGN

1 2

INHIBIT

Lock/Arm

Unlock/Disarm

Trunk Release/ Remote Start

Option

Function Button

Model PE2RELCD

Operators Manual

RF Upgrade Kit

Check with your installation center for features and functions operational on your system.

To Operate System:

1) Press the lock button to lock the doors and arm the alarm if installed.

2) Press the unlock button to unlock the doors and disarm the alarm if installed.

3) Press and hold the Trunk/Start button for 3 seconds to unlock the trunk.

4) Press the Trunk/Start button two times in succession to start the vehicle. The vehicle will start

and run the predetermined time set up during installation (5 to 60 minutes selectable).

Anytime during the run cycle, enter the vehicle by rst unlocking the doors with your transmitter,

insert your key and turn it to the run, NOT START, position, then step on the brake, the vehicle is

now in control of the ignition key.

NOTE: For push to start vehicle systems, simply enter the vehicle with your key in hand, and

step on the brake.

Consult your installation center for operation and information on convenience options 1 & 2

which may have been connected or added to your vehicle.

PATENTED: www.voxxintl.com/company/patents

Summary of content (12 pages)

PAGE 1
Model PE2RELCD Operators Manual RF Upgrade Kit PRESTIGE 24 S A Trunk Release/ Remote Start 12 Z Z Option F Function Button IGN INHIBIT AM PM Lock/Arm 0 Unlock/Disarm Check with your installation center for features and functions operational on your system. To Operate System: 1) Press the lock button to lock the doors and arm the alarm if installed. 2) Press the unlock button to unlock the doors and disarm the alarm if installed.
PAGE 2
Quick Stop Mode: With vehicle running, if you wish to make a quick stop and leave the vehicle running, once you arrive at your destination: a) place the gear selector in Park, b) set the parking brake, c) with your foot off the brake, press the transmitter button two times in succession. The vehicle will now be under control of the remote start system. Turn your ignition switch off, WITHOUT, stepping on the brake, and exit the vehicle. Lock the doors with the key to insure security.
PAGE 3
TRANSMITTER FUNCTION SELECTION TRANSMITTER BUTTON ICON DISPLAYED AM PM 18:88 TONE/VIBRATE TIMING ADJUST MODE (HRS) F PRESS FOR 5 SECONDS TIMING ADJUST MODE (MINS) F PRESS 1X AM PM 18:88 F PRESS 2X AM PM 18:88 USE KEY BUTTON OR OPTION BUTTON TO SELECT F PRESS 3X AM PM 18:88 USE KEY BUTTON OR OPTION BUTTON TO SELECT ALARM CLOCK & POWER UP MUSIC SELECT F PRESS 4X 8 ALARM CLOCK ADJUST MODE ON/OFF F PRESS 5X ON/OFF TIMING COUNT DOWN ADJUST MODE (HRS) F PRESS 6X AM PM 18:88 TIM
PAGE 4
ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 2500ft. Check Vehicle Status Press the lock+key+option buttons simultaneously for 1 second.
PAGE 5
NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time periodically as time may drift slightly each day. Timing Count Down The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. For instance you may have a meeting 4 hours from now and you want a reminder in 3 Hrs and 45 Mins.
PAGE 6
ALARM CLOCK This icon will be toggled on and off when the “F” + Trunk/Key buttons are pressed simultaneously. The feature must be set in the feature selection menu of the transmitter. COUNT DOWN TIMER The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. Setting information shown on previous page. S POWER SAVE FEATURE Press the “F” and Lock buttons simultaneously to toggle this feature on and off.
PAGE 7
The one way transmitter included with this kit operates in a similar fashion as the two way transmitter with respect to the buttons and are shown below for your reference. Lock Button Press once to lock and arm alarm. Press and hold 3 seconds for panic alarm where applicable. Unlock Button Press once to unlock and disarm alarm. Press and hold 3 seconds for panic alarm where applicable. Trunk / Start Button Press two times in succession to start vehicle.
PAGE 8
(Alarm & Keyless Systems Only) PROGRAMMING YOUR CUSTOM OVERRIDE CODE Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 9 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a preprogrammed override code of 11.
PAGE 9
(Alarm Systems Only) MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system’s memory. 1) Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound. 2) Within 5 seconds, press and release the Receivers push-button switch 1 time. 3) Within 5 seconds, turn the ignition switch off then on.
PAGE 10
OPERATING ON AUTOMATIC START UP TIMER MODE Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device.
PAGE 11
From step 3 above: a) Press and release the valet/programming button 3 additional times to get to channel 4, then Press any unused transmitter button or button combination to program channel 4. b) From a, press and release the valet/programming button 1 time to get to channel 5, then press any unused transmitter button or button combination to program.
PAGE 12
TO purchase replacement transmitters or to get additional product information go to： www.prestigecarsecurity.com FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.