User's Manual

ManualsBrandsNutek ManualsElectronicsTwo Way Remote Control Unit

128-6799D

1 of 8

Your Alarm and or Remote Start unit has a congurable receiver that allows

the transmitter to be programmed to operate the Lock Unlock functions with

one transmitter button or with two transmitter buttons (separate Lock/Unlock).

In addition, the receiver also allows driver priority function. This driver priority

function takes place when ever a particular transmitter is used to unlock the

vehicle regardless of the selection of one button or two button operation.

The following indicates the receiver programmable slots.

1 Lock/Unlock or Lock

2 Unlock if Programmed

3 Trunk Release & or Remote Start (Optional on some models)

4 Auxiliary Output

5 Auxiliary Output

6 Driver 1 Priority or Sperate Output

7 Driver 2 Priority or Separate Output

Receiver channels 6 or 7 will accept the programming of transmitter channel

1 if used as the Lock/Unlock button, or Channel 2 when separate Lock

Unlock buttons are programmed. In this way, whenever the transmitter is

used to unlock the vehicle, channel 6 or 7, when programmed, will provide

a pulsed ground output. This output can be connecter to the driver priority

function of the vehicle to reset preset user features. Please consult with your

installation centers technician to see if this feature is available in your vehicle.

NOTE: A total of 4 transmitters may be programmed into any receiver chan-

nel.

Force programming a transmitter, removing a transmitter, or reprioritizing a

transmitter is covered later in this manual.

Also, if you do not program a transmitter button into channel 2 which is the

separate unlock/disarm channel, then whatever button is programmed into

channel 1 will serve as both lock/arm & unlock/disarm.

Note: The RED Button serves as a function button in combination with other

buttons explained in your owners manual. This button may not be used to

operate a receiver channel.

NOTE: The Option Button is predetermined and programmed for access to

Time Start, and Temperature Start & Check so it cannot be used for multiple

button operation of any other feature. It will however operate for any single

button programming.

This transmitter is also capable of one button programming for certain model

Audiovox Alarms. If your alarm is one of these models, then when step 3 is

completed on the following page, you can turn the ignition switch off and pro-

gramming with the default button congurations for the rst four channels will

be complete.

Model 5BCR/5BCR03

5BCR05/5BCR07

Programming Guide

Summary of content (8 pages)

PAGE 1
Model 5BCR/5BCR03 5BCR05/5BCR07 Programming Guide Your Alarm and or Remote Start unit has a configurable receiver that allows the transmitter to be programmed to operate the Lock Unlock functions with one transmitter button or with two transmitter buttons (separate Lock/Unlock). In addition, the receiver also allows driver priority function.
PAGE 2
THIS PAGE LEFT BLANK INTENTIONALLY 2 128-6799D 2 of 8
PAGE 3
TO ENTER THE PROGRAM MODE: 1. Turn the ignition switch to the “ON” position. 2. Within 10 seconds, Press and release the valet/program switch three times. (Siren emits 1 short chirp indicating channel 1 has been entered) 3. Within 10 Seconds, Press and hold the button of the first transmitter you wish to control the Lock&Arm feature of your security system until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Lock/Arm feature). 4.
PAGE 4
13. Within 10 Seconds, Press and hold the unlock button, (or any unused button(s)), of the first transmitter you wish to control Channel 6 output, (Driver Priority 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1) 14. Within 10 seconds, press and release the valet program switch one time. (Siren emits 7 short chirps indicating channel 7 has been entered) 15 .
PAGE 5
To reprogram a receiver channel with a different transmitter button once a code has been stored, there will be two options: 1. Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of buttons, push out the stored code by pressing the unused button until a long chirp is heard, then repeat 3 additional times. After this, you can add any desired unused transmitter button.
PAGE 6
2. Slide back the battery case cover in the direction shown. 3. Remove the discharged battery, making note of the location of the + and contacts shown, and replace with a new type alkaline 1.5 volt AAA Battery. 4. Making note of the location of the (+) and (-) contacts, insert a new AAA battery alkaline 1.5 volt. 5. Replace battery cover being certain to close the battery case lock clip to prevent accidental opening.
PAGE 7
ORDER FORM FOR TRANSCEIVERS 5BCR/5BCR03/5BCR05/5BCR07 Attention: Transmitter Ordering Department Important: To help us expedite your order, please print all of the information legibly and mail this form and your payment according to the instructions below.
PAGE 8
FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.