RS-265-EDP+ / RS-260-EDP Deluxe 1-Button Keyless Entry & Remote Start December 19, 2014 Operation Guide v.1.1 Temporary cover. Color cover is in a separate file.
Table Of Contents Transmitter Overview ................................................................................................... 2 Transmitter Functions ................................................................................................... 3 Other Remote Start Features ....................................................................................... 4 Low Battery/Low Temp Automatic Starting ............................................................... 4 Turbo Timer Feature ...
Transmitter Functions LOCK / ARM: While the system is unlocked / disarmed, Press and hold the “START” button for 1 second. • THE SIREN / HORN WILL CHIRP & THE PARKING LIGHTS WILL FLASH ONCE. • 2-WAY RESPONSE: CONTROLLER WILL BEEP ONCE AND THE BUTTON WILL FLASH ONCE. UNLOCK / DISARM: While the system is locked / armed, Press and hold the “START” button for 1 second. • THE SIREN / HORN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE, THEN ILLUMINATE FOR 30 SECONDS.
Other Remote Start Features LOW BATTERY/LOW TEMP AUTOMATIC STARTING NOTE: Temperature Related Features Are Only Available On EDP+ models. This feature will automatically start the engine if the vehicle battery drops below 11 volts or the interior temperature drops to 15 (or 32) degrees fahrenheit. You must activate these features each time you park your car to use them.
Security System Features (OPTIONAL) This system is equipped with our exclusive VIRTUAL ALARM technology. The security functions described in this section are available as a simple upgrade from your dealer. It may require a plug-in module and some additional configuration, but will greatly enhance your system’s capabilities and add theft deterrence to your vehicle.
Using The Valet Switch EMERGENCY OVERRIDE If your controller isn’t usable and your alarm is armed, you’ll need to perform an emergency override to disarm the system and use your vehicle. To do so, use the following steps: STEP 1 - Enter the vehicle (the alarm should sound) STEP 2 - Turn the ignition key to the “ON” position (do not crank the engine). STEP 3 - Press the valet switch (located in the window-mount antenna) once. STEP 4 - Turn the ignition “OFF”.
The Status Light (cont’d) 1 FLASH: Run time expired. 2 FLASHES: Brake pedal was pressed. 3 FLASHES: Engine stalled or a bad tach signal. 4 FLASHES: Received transmitter command to stop. 5 FLASHES: The neutral safety circuit was triggered. 6 FLASHES: The alarm was triggered or low battery voltage. 7 FLASHES: The hood was opened. Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both) that are selectable via user feature #12.
Programming Features A matrix of all programmable features and their options are on the last page of this guide. For detailed information on each feature, please refer to the next section. Use the procedure below to make any necessary changes. TO MANUALLY CHANGE FEATURES: Step 1 Turn the ignition key “ON”, then “OFF” Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user features (Press 10 times to access installer features).
User Programmable Features (cont’d) Feature #4 - BROWN Wire Audible Output Pulsed Horn Low (press “start” 1 time to program) - DEFAULT Pulsed Horn Medium (press “start” 2 times to program) Pulsed Horn High (press “start” 3 times to program) Steady Siren (press “start” 4 times to program) This changes the BROWN wire’s audible output when the alarm is triggered. Steady siren must be selected when using a siren (other horn outputs stay at the Medium setting).
User Programmable Features (cont’d) Feature #11 - Confirmation Chirps Siren + Horn (press “start” 1 time to program) Siren Only (press “start” 2 times to program) - DEFAULT On Demand (siren+horn) (press “start” 3 times to program) Off (press “start” 4 times to program) This feature selects whether the siren and/or horn give confirmation chirps. Both outputs will always sound when the alarm system is triggered or in panic mode.
Installer Programmable Features (cont’d) “Data Tach” mode operates just like the “Tach Wire” setting except it takes its reading from the D2D data port instead of using the Violet/White wire. Before using, make sure this function is supported by the Databus Interface module. “Crank Only” AKA “blind start” is similar to the “Tachless” settings however, it only makes one start attempt and does not monitor engine running conditions. This is useful for many “push-tostart” vehicles.
Installer Programmable Features (cont’d) Feature #8 - Door Lock/Unlock Outputs 0.8 Second Outputs (press “start” 1 time to program) - DEFAULT 3 Second Outputs (press “start” 2 times to program) Double Pulse Unlock Output (press “start” 3 times to program) Total Closure Lock Output (press “start” 4 times to program) This changes the system’s doorlocking outputs to suite different vehicle requirements.
Installer Programmable Features (cont’d) Feature #14 - Pulse Ignition On Disarm On (press “start” 1 time to program) Off (press “start” 2 times to program) - DEFAULT This feature will pulse the ignition and activate any attached immobilizer bypass module for vehicles that require the ignition to be turned on to disarm the OEM alarm.
This device complies with FCC Rules part 15. Operation is subject to the following two conditions, (1) This device may not cause harmful interference and, (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Programmable Features Matrix SECURITY CONVENIENCE User Feature Programming: Ignition on, off, press valet 5 times # Feature Start Button 1 time Start button 2 times Start button 3 times Start button 4 times 1 Remote Start Run Time 10 min 5 min 15 min 20 min 2 Flashing Light Confirmations Unlock: ON RS: ON Unlock: ON RS: Flash Unlock: Flash RS: ON Unlock: Flash RS: Flash 3 Confirmation Chirp Volume Low Med-Low Med-High High 4 BROWN Wire: Siren / Pulsed Horn Pulse LOW Pulse MED Pulse
Back Cover Color cover is in a separate file.
