O W N E R ’S M A N U A L ® SECURITY SYSTEM with KEYLESS ENTRY 1
Congratulations Congratulations on the purchase of this CARBINE keyless entry and security system. Reading this owners guide prior to using the system will familiarize you with it’s many features. If issues arise or you have questions, contact your installing dealer first. Additionally, you can contact us online at www.carbine.com or call 310-735-2000. Replacement Remote Controls To purchase replacement remote controls, please see your authorized dealer/installer or visit us at www.carbine.
Contents Congratulations..........................................................................................2 Replacement Remote Controls....................................................................2 Remote Configuration.................................................................................4 LCD Configurations.....................................................................................5 Arming/ Disarming..........................................................................
Remote Configuration Button – – – Comment Lock/ Arm Press and release. Unlock/ Disarm Press and release. Panic Alarm On/Off Press and hold for 2 sec. Arm and delete the on-board shock sensor Press two times within 5 seconds. 2 short chirps + 1 long Arm and delete the optional sensor. On-Board shock Press three times within 10 seconds. 3 short chirps + 1 long sensor is active. Arm and delete the On-Board shock sensor and the optional sensor. Press four times within 15 seconds.
Standard LCD Icon Configurations LCD Icon Description LCD Icon Description The lock icon will be displayed when the doors are locked and the system is armed The unlock icon will be displayed when the doors are locked and the system is disarmed The valet mode icon will be displayed when the system is in valet mode The time display shows actual time, RS countdown time, alarm clock time and countdown timer Driver Paging Someone is paging you from your vehicle The remote is in range of the vehicle Th
LCD Icon Description LCD Icon Description The remote battery needs to be replaced The remote battery is full The door is open or the alarm has been triggered from an open door The hood is open or the alarm has been triggered from an open hood The trunk is open or the alarm has been triggered from an open trunk Button lock is active or the alarm was triggered by voltage from the ignition key The alarm was triggered by the shock sensor The shock sensor is inactive The tilt sensor is active The ala
Lock / Arm Press and release the button to arm the security system and lock the doors. The parking lights will flash one time. (door lock control must be installed) Unlock / Disarm Press and release the button to disarm the security system and unlock the doors. The parking lights will flash two times. (door lock control must be installed) Silent Arm / Disarm Press and release the button before pressing the or button to initiate silent mode.
Passive Arming/Locking Your CARBINE system can be programmed to Passive Arm and Lock the doors. If both of these features are programmed on, your CARBINE system will automatically arm and lock the doors 30 seconds after the last protected entrance is closed. During the 30 second countdown, the RCC LED will flash fast and the siren/horn will chirp after 20 seconds to warn that the system is about to arm and lock. 10 seconds later, the doors will lock.
Trunk Release (CH#3) Press and hold the button for 1.2 seconds to release the trunk/ hatch lid - The vehicle must have electronic trunk control - The trunk release control option must be installed AUX Output Activation (CH#4) Depending on your installation, your installer may have connected the channel #4 output to your vehicle. To activate the AUX/CH#4 output, press and hold the + buttons together for 2 seconds. This action will energize the AUX/CH#4 output for as long as you hold the buttons down.
Valet Mode (By Valet Button) Valet mode is a convenience when you take your car in for service or allow someone who may not be familiar with your security system to drive your vehicle. - All doors must be closed - Turn the ignition key On then Off. - Press and release the valet button (1) time. The status LED will be on. - Repeat the procedure to turn off the valet mode. The status LED will be off.
Trigger the System If at any time the system becomes triggered, the horn/siren will sound for 30 seconds and then re-arm. If a protected entrance is left open, the alarm will sound for three, 30 second cycles and then the protected entrance is bypassed while the remaining detection zones are active. Progressive Door Trigger This feature is ON by default and can be programmed off by the installer.
Forced Passive Arming As additional protection, the Forced Passive Arm feature will arm the security system 1 hour after exiting the vehicle. In some cases, you may forget to press the button to arm your system. Forced Passive Arming will keep the vehicle protected. By default, this system is ON and active unless programmed differently by the installer. Automatic Starter Disable The purpose of this feature is to keep your vehicle from being stolen at all times.
Ignition Key Controlled Dome Light - If dome light control has been installed, every time you stop the engine (Ignition Key Off), the dome light in your vehicle will illuminate. - When you disarm your security system the dome light will illuminate. When you enter the vehicle and turn On the ignition key, the dome light will go out. Note: Since this system mimics some factory installed dome light systems in many vehicle brands, the operation may not be noticed.
Arming the AHS To arm the AHS, enter the vehicle and close all the doors. Turn the ignition key to ON and then press the button on the CARBINE remote controller for 1 second. The parking lights will flash, and the siren will chirp once. AHS is now armed. Start the engine and drive the vehicle as normal. At this point, if you are forced from the vehicle, AHS will start a countdown sequence (See AHS triggered Sequence below) once the door is opened and closed.
AHS Triggered Sequence Once the AHS is triggered, the follow sequence will occur; - 15 seconds after the door(s) is closed, the LED in the RCC will begin to flash. - 45 seconds later, the horn/siren will begin to chirp and the parking lights will begin to flash. - 15 seconds later, the horn/siren chirping will change to a full alarm blast. The parking lights will continue to flash. - Once in full trigger mode, the siren/horn will blast and the parking lights will flash for 3 minutes and then stop.
The First 60 Seconds During the first 60 seconds of the triggering sequence (LED on the RCC is flashing), the AHS can be disarmed by turning ON the ignition key and pressing the button on the CARBINE remote controller. If you happen to be driving the vehicle, simply press the button on the remote controller. When the AHS is disarmed, the parking lights will flash and the siren/horn will chirp.
LCD Remote Controller Settings and Programming Enter Settings: To get into transmitter feature programming mode, press and hold the “F” button for 3 seconds. You will hear 2 beeps and the clock display will flash. Follow the instructions enclosed for each setting you want to program or change. Exit Settings: To exit any setting mode, push and hold the “F” button for 3 seconds or simply do nothing for 15 seconds.
Function Setting Daily Clock Display 1. Press the button to adjust hours. 2. Press the button to adjust minutes. 3. To exit the clock setting mode, push and hold the “F” button for 3 seconds or simply do nothing for 15 seconds. Note: Adjusting hours will change AM-PM. Adjusting minutes will not. 1. Press and release the “F” key once. The Alarm icon will display and the display will flash “12:00”. Alarm Clock Time Setting 2. Press the button to adjust hours. 3. Press the button to adjust minutes.
Function Setting Backlight Brightness Setting 1. Press and release the “F” key five times. “50p” will be displayed. 2. Press the button to adjust the light level. You have “0p”, “50p” and “100p” to choose from. Note: Raising the display brightness to 100p will consume more battery power.
Pairing a Replacement Remote Control Your CARBINE system remote controls are already paired to the control module. If you are replacing or adding remotes to your system, they must be programmed (paired) to the control module before they will operate the system. In order to perform remote control pairing, you must know where your “Valet Button is located as you will use the button and the LED indicator to perform the pairing function. Remote Pairing Procedure 1. Open the driver’s door. 2.
System Maintenance Replacing the LCD 2-Way Remote Controller Battery The CARBINE LCD 2- way remote controllers are powered by a CR2450 Lithium battery. When the battery begins to weaken, the battery life indicator on the LCD screen will display the condition of the battery. When the battery display reaches (1) bar, it is time to replace the battery. Full Replace Empty To replace the battery, follow the enclosed procedure. 1.
Replacing the 4 Button Remote Controller Battery The CARBINE remote controllers are powered by a CR2032 Lithium battery. When the battery begins to weaken, the operating range of the remote control is reduced and the LED indicator on the remote will begin to dim. To replace the battery, follow the enclosed procedure. 1. There is a slot built into the remote case. Use a dime or small flat blade screwdriver to separate the top and bottom cases of the transmitter. 2.
GOVERNMENT REGULATIONS This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.