Install Guide

®
REMOTE START with SECURITY & KEYLESS ENTRY SYSTEM
Quick Reference Install Guide
FOR PROFESSIONAL INSTALLATION ONLY!
If you are not proficient in the installation of this product or would like a full ver-
sion of the installation manual, please visit our web site @www.magnadyne.com
Receiver/Control
Center(RCC)
Pink: (+) Ignition 1 Input/Output
Red: +12V Input
Red: +12V Input
Red: +12V Battery Power
Brown: (+) Siren
16 PIN
(see chart)
Black: System Main Ground
White: Parking Light Relay Output
Blue: - Negative Door Unlock Output
Green: - Negative Door Lock Output
White: Parking Light Relay Power Input
Violet: Starter Output
Pink/White: Ignition 2 Output
Orange: Accessory Output
Fortin or iDatalink
Bypass Module
30A
30A
15A
10A
16
5678
9101115 14 13
4 3 2
12
1
16 Pin Accessory Harness Wiring:
Pin Color Function Pin Color Function
1 Green/White (-) Factory Alarm Re-Arm Output 9 Orange (-) GND When Armed/Lock
2 Gray (-) Hood Pin Safety Input 10 Red/White (-) Channel 3 Output (Trunk)
3 Black/White (-) Parking Brake Input 11 Lt. Purple/Yellow (-) Starter Output
4 Blue (-) Trunk Trigger 12 Lt. Green/Black (-) Factory Alarm Disarm Output
5 Brown (+) Vehicle Brake Safety Input 13 Brown/Black (-) Horn
6 Green (-) Door 14 Dk. Blue Ground While Running
7 Violet (+) Door 15 Orange/White (-) Accessory Output
8 Lt. Violet/White Tach Input (AC) 16 Pink (-) Ignition Output
Mounting the Receiver/Control Center (RCC):
1. Choose a location on the upper or sides of the vehicle windshield.
A higher location is best.
2. Remove the backing liner from the mounting tape on the backside
of the RCC and stick it to the windshield glass.
3. Route the RCC cable to the location of the control module.
Programming System Features:
All CARBINE remote start systems have a menu of features that can
be programmed to suit the installation requirements of any vehicle.
These features can be set by using the RCC button Feature Programming
procedure or by Windows PC programming and the CARBINE web app.
Feature Programming by RCC Button
1. Open the driver’s door.
2. Turn the ignition key ON then OFF.
3. Within 5 seconds, press and hold the RCC button to select the menu.
- A single chirp indicates Menu #1.
- Hold the button longer for two chirps. You are in menu #2.
- Continue holding the RCC button for three chirps. You are in menu #3.
4. When the desired menu is reached, release the RCC button.
5. Within 5 seconds, press and release the RCC button the number of
times corresponding to the feature you want to change then press and
hold the button once more to lock the feature. The siren / horn will chirp
to match the feature selected. Release the RCC button.
Note: RCC switch pushes are sequential. For example, if you start at
feature #1, then push and release the valet switch 2 more times, you
will be at feature #3 and so on. Always remember to push and hold
the valet switch one more time after each selection to lock the feature
before using the transmitter to change the setting.
6. Use the or buttons on the CARBINE remote to adjust the feature.
7. For features with only two options, the = 1 Chirp setting,
while the = 2 Chirp setting.
8. For features with more than two settings, the button selects the
settings in ascending order. Press and release the button as many
times necessary to adjust the feature.
9. The horn/siren will chirp indicating which setting is selected.
10. Turn the ignition key to ON to exit feature programming.
Menu #1 (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
1 Data Protocol
ADS
Fortin
2
Confirmation
Chirps
On
Off
3 System Arming
Active
Passive
4
Door Locking
Mode
Active
Passive
5
Forced Passive
Arming
On
Off
6
Ignition Key
Controlled
Locking
Off
On
7
Ignition Key
Controlled
Unlocking
Off
On
8
Panic with
Ignition On
Off
On
9
Armed While
Driving
Off
On
10 Door Lock Pulse
0.8
sec
3.5
sec
0.4
Sec
11 Horn Output
20
ms
30
ms
40
ms
50
ms
Panic
Only
12 Comfort Closure
Off
CC1 CC2
13
Tilt Sensor
Adjust
3*
1.5* Off
Menu #2 (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
1
Progressive
Door Trigger
On
Off
2
Nuisance Pre-
vention Circuit
On
Off
3
Valet Switch
Pulse Count for
Override
1
Pulse
2
Pulses
3
Pulses
4
Pulses
5
Pulses
4
Door Trigger
Error Chirp
On
Off
5
Double Pulse
Lock
Off
On
6
Double Pulse
Unlock
Off
On
7 Siren Duration
30 sec
60 sec
8
Factory Alarm
Disarm with
Trunk Release
On
Off
9
Factory Alarm
Disarm Pulse
Single
Double
10
Factory Alarm
Disarm
With
Unlock
Before
Unlock
Remote
Start
Only