Install Guide

Menu #3 (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
1
Transmission
Type
Automatic
Manual
2
Engine Checking
Mode
Wireless
Tach
Voltage
Wired
Tach
Off
3
Cranking
Duration
0.6 Sec
0.8 sec 1.0 sec 1.2 sec
1.4
sec
1.6
sec
1.8
sec
2.0
sec
4.0
sec
4
Remote Start
Run Time
12
Minutes
24
Minutes
60
Minutes
5
Diesel Start
Delay
Off
Timer
15 sec
Timer
35 sec
Timer
45 sec
6
ACC Output
During Diesel
Wait to Start
Off
On
7
2nd Ignition
Behavior
Ignition 1
Accessory
8
Parking Light
Behavior
Constant
Flashing
9
Timer Mode Run
Time
12
Minutes
3
Minutes
6
Minutes
9
Minutes
10
Turbo Timer Run
Time
1
Minute
3
Minutes
5
Minutes
10
Minutes
Access another feature within the same menu
1. Press and release the RCC Button the number of times to advance from
the last feature programmed to the next feature to be programmed.
2. Press the RCC button and hold it.
3. Use the CARBINE remote and follow steps 5 or 6 above to adjust
the feature.
Access another menu
1. Press and hold the RCC Button
2. After 3 seconds, the system will advance to the next menu and
conform with chirps and LED flashes.
Exiting the feature program mode
1. Set the ignition key to ON. A long confirmation chirp will be hear
if a horn or siren is connected.
2. Automatic after 30 seconds with no input from the RCC button
(long chirp).
3. The RCC button has been press too many times (long chirp).
Feature Programming by PC/App
1. A windows computer with internet support is required. The APP supports
Windows 7 (sp1) thru Windows 10 (Apple/Mac computers are not supported)
2. The programming adaptor model #ALA-21P is required
3. Follow the instructions provided with the ALA-21P accessory.
Engine Checking Mode:
The engine checking mode on all CARBINE remote start systems is set at
“Wireless Tach” by default. Once all the wiring is complete and correct, the
engine can be remote started without any other changes.
Engine type, Extreme weather etc. may require a more defined type of
engine checking for reliable operation. Use the information enclosed to
setup alternate engine checking modes.
Wireless Tach Learning
1. After the installation is completed, use the CARBINE key fob and
initiate the remote start sequence.
2. If the engine does not start on the first attempt, let the CARBINE
module cycle and attempt to start the engine again. Up to (3) cranking
attempts may be needed to start and run the engine.
3. When the engine starts and runs, let it run for at least 30 seconds.
4. Use the CARBINE key fob to shut down the engine.
Wireless Tach is programmed.
Hardwire Tach or Data Tach
- Hardwire Tach requires the Lt.Violet/White wire to be connected to
a fuel injector wire or a coil wire.
- Check the data bypass module spec to make sure it will provide a data
tach signal. Additional pre-programming of the data module may be
required. Refer to the data module instructions.
To learn the tach signal
1. Start the vehicle with the key.
2. Within 5 seconds, press and hold the valet button on the RCC.
3. Once the tach signal is learned, the blue LED on the RCC will
light or flash.
- When tach learning from a hardwire connection, the parking
lights will flash one time
- When tach learning via the data module, the parking lights will
flash two times.
Note: Depending on the data bypass module used, you may have to put
the bypass module into tach learning mode first before performing the
above procedure. Review the instructions of the data bypass module
before proceeding.
Pairing a Remote Controller:
Your CARBINE system remote controls are already paired to the control
module. If you are replacing or adding remotes to your system, they must
be programmed (paired) to the control module before they will operate the
system. In order to perform remote control pairing, you must know where
your “Valet Button is located as you will use the button and the LED indica-
tor to perform the pairing function.
Remote Pairing Procedure
1. Open the driver’s door.
2. Insert the ignition key into the key cylinder. Turn ON the ignition key.
3. Press and release the valet button then press and hold the valet button
for 1.5 seconds. The LED flashes and the horn/siren chirps (if connected).
Release the valet button. The system is now in pairing mode and will
stay in Pairing mode for 60 seconds.
5. Press and hold the button on the new remote control.
6. Press and release the button 5 times.
A. The LED on a 4 button transmitter will begin to flash slowly.
B. The word (PAir) will be displayed in the clock area of a
5 button LCD transmitter.
The remote will remain in this state for 15 seconds.
7. Press and release the button on the new transmitter.
The horn/siren chirps 1 long chirp. The new remote is programmed.
8. Turn the ignition key to the Off position. A long chirp from the horn
confirms that the pairing mode is off.
Note: Your CARBINE security system will accept codes from up to
(4) transmitters.
Remote Start Shutdown Diagnostics
If the remote starter activates but the engine fails to remain running,
a diagnostic procedure can be run to try and determine where the
fault in the system is.
To Perform Shutdown Diagnostics
1. With the ignition key Off, press and hold the RCC button.
2. While holding the RCC button, turn the ignition key On then Off.
3. Release the RCC button.
4. Press and release the RCC button one time.
The RCC LED will report the last shutdown reason for 1 minute or
until the ignition key is turned On again. Compare the LED flashes
to the chart below.
Status LED Flashes Reason for Shutdown
1 Over-Rev Shutdown
2 Runtime Expired
3
Shutdown by Transmitter (or
Optional Push button)
4 Low or No RPM Detection
5 Hood Open Shutdown
6 (+) Brake Shutdown
7 (-) Parking Brake Shutdown
9
Low Vehicle Battery (Voltage
Checking Mode Only)
10 Wait-to-Start
11
Alarm Trigger During
Remote Start
Programming the Digital Shock Sensor:
Follow the enclosed procedure to set the sensitivity of the
digital shock sensor.
Note: The pre-warning sensitivity adjusts in proportion
to the shock sensitivity.
1. Set the system in disarmed mode.
2. Turn the ignition key ON/OFF 3 times (ending in off).
3. Within 5 seconds, press + buttons together for 2 seconds.
The horn/siren will emit (1) long chirp to indicate you are in Shock
Sensor Sensitivity Adjustment Mode.
4. To increase sensitivity, press the button. Each time you press the
button you will hear (1) chirp. When you reach the MAX level
adjustment, you will hear 1 short + 1 long chirp.
5. To decrease sensitivity, press the button. Each time you press the
button you will hear (2) chirps. When you reach the MIN level
adjustment, you will hear 2 short + 1 long chirp.
6. The shock sensor has 20 steps available for adjustment.
The default setting is 10.
7. To return the shock sensor back to it’s default setting,
press and release the button. You will hear 3 chirps.
8. During the process you can test by knocking:
1short chirp - prewarn; 1 Long chirp - TRIGGER
To exit the Shock Sensor Sensitivity Adjustment Mode, turn the
ignition key on. You will hear 3 long chirps.
Reset and Deletion
If the programmable features need to be reset to default or the
Wireless Tach feature needs to be reset for re-programming,
follow the enclosed procedure.
1. Open the drivers door.
2. Turn the ignition key to the ON position
3. Within 5 seconds, press and release the RCC button the number
of times required below to perform the task.
- Press and release the RCC button two times to delete all of the
programmed remote controls.
- Press and release the RCC button three times to delete all features
programming back to their default settings.
Note: This procedure does not erase Wireless Tach information.
- Press and release the RCC button four times to erase all pre-learned
Wireless Tach information.
4. Once you have selected the function you want to perform, press and
hold the RCC button. The RCC LED will flash and the horn will chirp
(if connected) to confirm the functional step chosen. Do Not release
the button.
5. Press and release the button of a programmed remote.
The horn will chirp to confirm the feature has been reset/deleted.
6. Release the RCC button and turn off the ignition key. The horn will
chirp (if connected) to confirm exit.
Magnadyne Corporation
1111 W. Victoria Street Compton CA 90210 [phone]
For Warranty Information: Please Visit Our Website at www.magnadyne.com
IM_QS-55CSR