Install Guide

®
REMOTE START with SECURITY & KEYLESS ENTRY SYSTEM
Quick Reference Install Guide
FOR PROFESSIONAL INSTALLATION ONLY!
If you are not proficient in the installation of this product or
would like a full version of the installation manual, please
visit our web site @www.magnadyne.com
26 PIN
(see chart)
Receiver/Control
Center(RCC)
2nd Sensor
Port
15A
10A
20A
20A
20A
Green: (+) Starter Input
Violet: (+) Start Output
Red / Black: (+) Battery Input (1)
Orange: (+) Accessory Output
Pink / Black: (+) Ignition 2/ Acc Isolation
Red: +12V Battery Power
Brown: (+) Siren Output
Black: System Main Ground
White: Parking Light Relay Output
White: Parking Light Relay Power Input
Blue: - Negative Door Unlock Output
Green: - Negative Door Lock Output
Red / White: (+) Igniton 2/ Flex Relay
Pink / White: (+) 2nd Ignition or 2nd Accessory Output
Pink: (+) Ignition Input/Output
Red: (+) Battery Input (2)
Fortin or iDatalink
Bypass Module
26
410
1
192021 16 15 141718
25 24 23
22
8 7 69 511 312 213
26 Pin Harness
Pin Color Function Pin Color Function
1 White/Violet (-) 2nd Unlock Output 14 Black/Yellow (-) Dome Light Supervision Output
2 Red/White (-) Channel #3 Output 15 Blue/White (-) 2nd Status or Rear Defog Output
3 Orange (-) Ground When Armed 16 Dark Blue (-) 1st Status Output
4 Brown (+) Brake Switch Shutdown 17 Green/White (-) Re-Arm the Factory Alarm Output
5 Gray (-) Hood Pin Shutdown 18 Lt. Green/Black (-) Disarm the Factory Alarm Output
6 Black/White (-) Parking Brake Switch Input 19 Brown/Black (-) Horn Output
7 Blue (-) Instant trigger Trunk/Hood pin input 20 Orange/Black (-) AUX Channel #6 Output
8 White/Blue (-) External Activation Input 21 White/Black (-) AUX Channel #5 Output
9 Gray/Black (-) Diesel What to Start Input 22 Violet/Black (-) AUX Channel #4 Output
10 Violet (+) Door Trigger Input 23 Violet/Yellow (-) Starter Output
11 Green (-) Door Trigger Input 24 Orange/White (-) Accessory Output
12 EMPTY No Connection 25 Pink/White (-) 2nd Ignition or Acc Output
13 Violet/White (AC) Tach Input 26 Pink (-) Ignition Output
Mounting the Receiver/Control Center (RCC):
1. Choose a location on the upper or sides of the vehicle windshield.
A higher location is best.
2. Remove the backing liner from the mounting tape on the backside
of the RCC and stick it to the windshield glass.
3. Route the RCC cable to the location of the control module.
Programming System Features:
All CARBINE remote start systems have a menu of features that can
be programmed to suit the installation requirements of any vehicle.
These features can be set by using the RCC button learning procedure
or by Windows PC programming and the CARBINE web app.
Feature Programming by RCC Button
1. Open the driver’s door.
2. Turn the ignition key ON then OFF.
3. Within 5 seconds, press and hold the RCC button to select the menu.
- A single chirp indicates Menu #1.
- Hold the button longer for two chirps. You are in menu #2.
- Continue holding the RCC button for three chirps. You are in menu #3.
4. When the desired menu is reached, release the RCC button.
5. Within 5 seconds, press and release the RCC button the number of
times corresponding to the feature you want to change then press and
hold the button once more to lock the feature. The siren / horn will chirp
to match the feature selected. Release the RCC button.
Note: RCC switch pushes are sequential. For example, if you start at
feature #1, then push and release the valet switch 2 more times, you
will be at feature #3 and so on. Always remember to push and hold
the valet switch one more time after each selection to lock the feature
before using the transmitter to change the setting.
6. Use the or buttons on the CARBINE remote to adjust the feature.
7. For features with only two options, the (lock icon) = 1 Chirp setting,
while the = 2 Chirp setting.
8. For features with more than two settings, the button selects the
settings in ascending order. Press and release the button as many
times necessary to adjust the feature.
9. The horn/siren will chirp indicating which setting is selected.
10. Turn the ignition key to ON to exit feature programming.
Menu #1 (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
1 Data Protocol
ADS
Fortin
2
Confirmation
Chirps
On
Off
3 System Arming
Active
Passive
4
Door Locking
Mode
Active
Passive
5
Forced Passive
Arming
On
Off
6
Ignition Key
Controlled
Locking
Off
On
7
Ignition Key
Controlled
Unlocking
Off
On
8
Panic with
Ignition On
Off
On
Menu #1 continued (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
9
Armed While
Driving
Off
On
10
Auto Starter
Disable
On
Off
11
Door Lock
Pulse
0.8
sec
3.5
sec
0.4
Sec
12 Horn Output
20
ms
30
ms
40
ms
50
ms
Panic
Only
13
Horn Honk
Mode
Pulsed
Constant
14
Comfort
Closure
Off
CC1 CC2
15
Tilt Sensor
Adjust
3*
1.5* Off
Menu #2 (Default in Bold)
Item Feature
Chirps
1 2 3 4 5 6 7 8 9
1
Progressive
Door Trigger
On
Off
2
Nuisance Pre-
vention Circuit
On
Off
3
Valet Switch
Pulse Count for
Override
1
Pulse
2
Pulses
3
Pulses
4
Pulses
5
Pulses
4
Door Trigger
Error Chirp
On
Off
5
Double Pulse
Unlock
Off
On
6
Double Pulse
Lock
Off
On
7
Ignition Key
Controlled
Dome Light
On
Off
8 Siren Duration
30 sec
60 sec
9
Factory Alarm
Disarm with
Trunk Release
On
Off
10
Factory Alarm
Disarm Pulse
Single
Double
11
Factory Alarm
Disarm
With
Unlock
Before
Unlock
Remote
Start
Only
12
Channel #4
Linking
None
Arm Disarm
Remote
Start
13
Channel #4
Output Type
Button
Hold
Latched
Latched
Off with
ignition
30
sec
60
sec
90
sec
14
Channel #5
Linking
None
Arm Disarm
Remote
Start
15
Channel #5
Output Type
Button
Hold
Latched
Latched
Off with
ignition
30
sec
60
sec
90
sec
16
Channel #6
Linking
None
Arm Disarm
Remote
Start
17
Channel #6
Output Type
Button
Hold
Latched
Latched
Off with
ignition
30 Sec
60
sec
90
sec