al-185X-eDPb Deluxe 2-way alarm & Remote Start may 29, 2013 Operation guide Temporary cover. Color cover is in a separate file.
Table Of Contents Controller & Transmitter Overview ������������������������������������������������������������������������������� 3 The 2-Way Controller ����������������������������������������������������������������������������������������������� 3 The 1-Way Transmitter ��������������������������������������������������������������������������������������������� 3 Controller & Transmitter Functions ������������������������������������������������������������������������������� 3 Other Remote Start Feat
Controller & Transmitter Overview The 2-Way COnTROlleR 1 Controller part number: 154-03 (black w/ CR2032 batteries) 157-03 (red w/ rechargeable battery) 158-03 (black w/ rechargeable battery) 2 1) antenna: Sends commands to the system and receives confirmations for 2-way functions. 2) lCD Display: Displays all controller functions as well as the status of your system. 3) Control buttons: Will light up when pressed 3 4) Charging Port (rechargeable models only): The buttons will flash while charging.
Controller & Transmitter Functions (cont’d) unlOCK / DiSaRm: Press and release the “UNLOCK” button • THE SIREN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE THEN ILLUMINATE FOR 30 SECONDS • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL SHOW THE UNLOCK/ DISARM ICON AND BEEP TWICE (1-WAY TRANSMITTER: PRESS THE UNLOCK BUTTON) TRunK ReleaSe / Channel 2: Press the “TRUNK” button for 3 seconds • THE SYSTEM WILL DISARM AND THE TRUNK WILL OPEN (IF EQUIPPED) • UPON RECEIVING CONFIR
Controller & Transmitter Functions (cont’d) The engine will run for the preset run time (see user feature #17). * • Run Time extender: Press the “ ” button one time during remote start to restart the engine run timer The timer will restart at “0:00” nOTe: This can only be used once per remote start cycle. The controller will also give you “run time expiration” warning (2 chirps) 1 minute before the remote start cycle ends.
Controller & Transmitter Functions (cont’d) PaniC: Press and hold the “LOCK” or “UNLOCK” button for 3 seconds • THE SIREN/HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED (1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK OR UNLOCK BUTTON FOR 3 SECONDS) OR SilenT aRm / DiSaRm: Press and release the “TRUNK” button twice in 5 seconds • THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK/ARM OR UNLOCK/DISARM DEPENDING ON THE CURRENT SYSTEM STA
Controller & Transmitter Functions (cont’d) * RemOTe ValeT: Press and release the “ ” button within 5 seconds of unlocking/disarming the alarm system. • THE SYSTEM WILL ENTER ALARM VALET MODE SEE PAGE 10 FOR MORE INFO ON VALET MODES 1 2 (1-WAY TRANSMITTER: PRESS AND RELEASE THE “START” BUTTON WITHIN 5 SECONDS OF DISARMING THE SYSTEM) auXiliaRy FunCTiOnS 1-4: The actual operation of these functions will vary from car to car.
Other Remote Start Features (cont’d) Turbo Timer Feature It is typically recommended that vehicles equipped with turbocharged engines allow the engine to idle after driving to cool the turbocharger. When this Installer Programmable Feature #4 is enabled, the system will automatically keep the engine running as follows: • With the engine running, hold the brake pedal and engage the parking brake.
Security System Features (cont’d) Automatic Rearming This automatically rearms the alarm if the system is disarmed from the remote. (see user feature #3). When disarmed by remote, the system will start a 90 second countdown (fast flashing status light) to arm the system. This is useful if the controller may accidentally disarms the system when it’s kept in a purse or pocket where other items could potentially press the buttons.
Using The Valet Switch (cont’d) Valet Modes ALARM VALET MODE, while active, completely disables all security functions. Keyless entry and remote start are still operable. To enter valet mode, perform the following steps: STEP 1 - Disarm the system either with the controller or by performing an emergency override (make sure not to hold the brake pedal). STEP 2 - Press and hold the valet switch (located in the window-mount antenna) for 2 seconds.
The Status Light The status lights, located in the window-mount antenna, provide a visual indication of the system’s status via GREEN (remote start status) and RED (alarm status) lights. SECURITY SYSTEM STATUS (RED LIGHT): OFF: The alarm is disarmed and not performing any automatic functions. ON CONSTANT: The alarm is in valet mode. FLASHING SLOW: The alarm is armed and monitoring all entry points. FLASHING FAST: One of the automatic arming features is in progress.
The Status Light (cont’d) SOLID GREEN W/ RED FLASH: System is in remote start valet w/ the alarm armed. SOLID RED W/ GREEN FLASH: System is in alarm valet w/ remote start activated. FAST ALTERNATES GREEN/RED: Alarm armed w/ remote start activated. SLOW FLASHING GREEN W/ 1-4 RED FLASHES: Zone violation recall during remote start mode. SLOW FLASHING RED W/ 1 GREEN FLASH: System is armed and ready to remote start in manual transmission mode.
Controller Options (cont’d) Setting The Clock 1) Press the “P” button for 5 seconds to access the controller features. The controller will beep twice. 2) Press and release the “P“ button once to select the clock (hour digits will flash). 3) Press the “TRUNK“ button to scroll up or the “ “ button to scroll down. 4) Press the “P” button to switch to the minute digits. 5) Press the “TRUNK“ button to scroll up or the “ “ button to scroll down.
Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both). All are programmable, and must be turned on to operate. Once activated, the user has 53 seconds to cancel the Anti-Carjacking protection process (described below). If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition.
Programming Controllers/Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature. Before you begin, have all transmitters which are to operate the system at hand and make sure the correct vehicle profile (see page 12) is selected on the controller(s). Step 1 Then, turn the ignition “on”. Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times.
User Programmable Features Feature #1 - SecureCode DEFAULT - 1 Press SecureCode is a unique patented feature which allows you to custom select the number of Valet Switch presses in two stages, instead of a single “1 press”, which would be required in order to perform an Emergency Override. If any of the three anti-carjacking features are utilized, a customized SecureCode would also be required to turn it off once it is fully activated. The SecureCode operation is described on page 10.
User Programmable Features (cont’d) Feature #5 - Ignition Activated Override Off (press “unlock” button to program) - DEFAULT On (press “lock” button to program) This feature allows an activated system to be overridden and disarmed by simply turning the ignition switch on within 10 seconds of the system’s activation. After 10 seconds, the Emergency Override must be performed.
User Programmable Features (cont’d) Feature #11 - Flashing Light Confirmations On w/ Disarm, Flash w/ RS (press “unlock” button to program) - DEFAULT On w/ Disarm & Remote Start (press “lock” button to program) On During Remote Start (press “trunk” button to program) Flashing During Remote Start (press “start” button to program) This feature affects the parking light confirmations for system disarm & remote start functions.
User Programmable Features (cont’d) Feature #17 - Remote Start Activation Press “start” button 2 times (press “lock” button to program) - DEFAULT Press “start” button 1 time (press “unlock” button to program) Press Lock & Unlock (press “trunk” button to program) This feature changes how the remote start feature is activated using the controller or transmitter. It also affects how many pulses activate remote start from the WHITE/ BLUE activation input wire.
Installer Programmable Features (cont’d) Feature #3 - Horn Relay Functions Horn Output (press “lock” button to program) - DEFAULT Door Unlock (press “unlock” button to program) Trunk Release (press “trunk” button to program) Pulse After Start (press “start” button to program) The primary function of this second relay, is to operate the vehicle’s existing horn; either in conjunction with the electronic siren, or in place of the siren.
Installer Programmable Features (cont’d) Feature #7 - Starter Cranking Time 0.75 Second (press “lock” button to program) - DEFAULT 1.00 Second (press “unlock” button to program) 1.5 Seconds (press “trunk” button to program) 2.25 Seconds (press “start” button to program) This feature determines the crank time of the 1st start attempt when in “Tachless” mode. If the engine doesn’t start on the first attempt, it will retry up to 3 more times extending the crank time by an additional 0.
Installer Programmable Features (cont’d) Feature #12 Low Temp Crank Extender 0ms (Off) (press “lock” button to program) 200ms (press “unlock” button to program) - DEFAULT 300ms (press “trunk” button to program) 400ms (press “start” button to program) When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the base timing (see installer feature #7).
Programmable Features Matrix User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button 1 Secure Code 1, 0 (default) Unlock button Trunk button 2 Last Door Arming 3 Automatic Rearming ”START” button Off On w/o lock On w/ Lock Off On w/o lock On w/ Lock Enhanced Rearm 4 Starter Interrupt Functions Alarm Anti-Grind Only Alarm+Anti-Grind Automatic 5 Ignition Override On Off 6 Ignition Lock/Unlock Off Lock w/ IGN ON Unlock w/ IGN Off Lock + Unlock w/ IGN On/
Back Cover Color cover is in a separate file.
LIMITED LIFETIME WARRANTY Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT (the Company), are warranted to be free from defects in materials and workmanship under normal use.
