Use and Care Manual

CI377W CANSWEEP
®
TEMPLATE
6¾"
2⅜"

If by any chance the opening was cut too big,
a trim plate (part number CI376W) is available
to provide a perfect cover.
AA0044
Trim plate
CI377W CanSweep
®
Under Cabinet Installation
Template
AR0050A

Align the template
(cut from this
instruction sheet)
onto the kick plate to
the desired location,
and trace the outline
of the area.
AR0054
Mark Center

Cut out the desired
opening and
discretely mark the
center of the
opening on the floor.
AR0055

Drill a small
reference hole
along the
center line
behind the
kick plate
through the
subfloor.

Locate the
reference hole from
beneath the
subfloor. Cut a
4” x 4” access hole
on your chosen
position along the
center line under
the kick space.
AH0008
Cabinet Space
Kick Space
Kick Plate
Opening
Reference
Hole
4" x 4" Access
Hole
Solvent weld a coupling
to a piece of 2” central
vacuum pipe, long enough
to reach the 4” x 4” access
hole from the opening on
the kick plate (Fig. A).
Friction fit the other end
of the coupling to the
CanSweep
®
until secure.
Do not glue, friction fit only
(Fig. B).
AR0057

Insert the
CanSweep
®
/pipe
into the opening on
the kick plate.
Use a 90° sweep
elbow fitting to
determine a cut
mark on the other
end of the pipe.
Then cut the pipe
at the mark.

Slide the
low voltage wires
into the
CanSweep
®
clips
as shown to
complete the wiring
connections.

Slide the
CanSweep
®
/pipe
and low voltage
wires into the
opening on
the kick plate. Glue
both ends of the
elbow to the piping
system, and then
secure the
CanSweep
®
to the kick plate with the 2 supplied screws.
AR0056
Fig. A
Fig. B

AE0051
AD0093
Screws
Glue elbow
to pipe
CI377W CanSweep
®
Baseboard Wall Installation
Template
AR0058A

Choose a desired
position on the baseboard
between two studs.
Place the template (cut
from this instruction sheet)
on the position, and trace
the outline of the area.
AR0059
2" x 4" Bottom Plate

Trim the opening on
the baseboard and
through the drywall
until reaching the
2" x 4" bottom wall
plate.

Against the edge of the
2" x 4" bottom plate, mark the
center of the opening.
AR0061
Reference
Hole
2" x 4"
Bottom Plate
Make piping
connections as
required and
ready the short
90° elbow in position
behind the CanSweep
®
.
Make sure that the opening of the elbow will securely
attach onto the spigot on the back of the CanSweep
®
when it is time for connection.
AD0094

Slide the
CanSweep
®
and
low voltage wires
into the opening
on the
baseboard.
Friction fit the
CanSweep
®
spigot into the elbow. Secure the CanSweep
®
to the
baseboard with the 2 supplied screws.
AE0052
Do not glue
CanSweep
®
to
the elbow.
Attach wires

AR0060
Mark Center

Drill a small reference hole
at the mark through the subfloor to below.
Locate the reference hole from below
and measure back 1
7
/8”. Use a 2” hole saw
to remove the 2"x4" bottom plate
section behind the opening.
Reference Hole
1⅞"
Slide the low volt wires into the CanSweep
®
clips
as shown to complete the wiring connections.
99046052A
Broan
www.nutone.com
1-888-336-3948