READ AND SAVE THESE INSTRUCTIONS Installer: leave this guide with homeowner. Register your product online at www.nutone.com/register.
Page 2 RN80L n RN110L Installation Guide WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
Page 3 RN80L n RN110L Installation Guide New Construction Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • Phillips screwdriver • 4" round metal ducting recommended for best performance. Use of other ducting is acceptable but may impact performance.
Page 4 RN80L n RN110L Installation Guide New Construction Installation and 3 Snap-in Secure Housing 1 2 ! snap 4 Position Housing between joists and crimp channel on both sides of Mounting Frame to lock Housing in place. Do not crimp Housing.
Page 5 RN80L n RN110L Installation Guide New Construction Installation 5 Connect Wires and Install Knockout Plate • Run 120VAC electrical wiring to the installation location. • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. • Connect wires as shown in wiring diagram. • Do not use a dimmer switch to operate the light. 1 Attach cable clamps to Knockout Plate. Knockout Plate mounts to outside of Housing and may be oriented as desired.
Page 6 RN80L n RN110L Installation Guide New Construction Installation Mask and 6 Insert Finish Ceiling • Install ceiling material. • Cut out around Housing. Mask protects unit during construction. Remove before installing Grille. 7 Install Grille 1 2 3 8 Install Bulbs 3 Night Light (purchase separately) 2 1 See Page 12 for Operation and Cleaning and Maintenance. See Page 13 for Troubleshooting.
Page 7 RN80L n RN110L Installation Guide Retrofit Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • Ruler • Tape to seal duct connections • Phillips screwdriver • Pencil • Flathead screwdriver • Drywall saw • Existing rigid duct will require the addition of a short length of flexible duct • Pliers • Claw hammer or pry bar • Wire insulation stripper • Utility knife • Wire cutter 1 • Electrical wiring and supplies per local code requirements • 4W (max.
Page 8 RN80L n RN110L Installation Guide Retrofit Installation 5 Remove Blower Assembly Set aside Blower Assembly 2 Both sides 3 1 6 Remove Wiring Panel Set aside Wiring Panel Set aside screw 1 2 7 Insert Mounting Frame 4 3 5 1 Remove screws from Mounting Frame and set aside 2 Bend up four tabs
Page 9 RN80L n RN110L Installation Guide Retrofit Installation 8 Secure Mounting Frame Screws set aside in Step 7 9 Snap-in Housing 2 ! snap 1 Pull existing wiring into Housing as it is inserted into Mounting Frame 10 Attach Flange, Transition, and Ducting 4 Pull existing ductwork into Housing Screw from Parts Bag 4" Ducting 2 Align 1 3 Insert tab into slot inside Housing Tape Transition Tape Flange
Page 10 RN80L n RN110L Installation Guide Retrofit Installation 11 Install Knockout Plate, Connect Wires and Install Wiring Panel • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. • Connect wires as shown in wiring diagram. • Do not use a dimmer switch to operate the light. 1 Attach cable clamps to Knockout Plate. Knockout Plate mounts to inside of Housing and may be oriented as desired.
Page 11 RN80L n RN110L Installation Guide Retrofit Installation 12 Insert and Secure Blower Assembly 2 3 Screws from Parts Bag 1 13 If ceiling repairs are needed, place Mask in Housing after Blower Assembly is secured. See New Construction Installation Step 6. Remove Mask before installing Grille.
2 Page 12 RN80L n RN110L Installation Guide 3 14 Install Bulbs 3 Night Light (purchase separately) 2 1 WARNING Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Page 13 RN80L n RN110L Installation Guide Troubleshooting Service Parts Symptom: The fan does not run. • Check for an open fuse or circuit breaker in the building’s service panel. 1 2 • Check that the plug-in connection for the Motor is seated firmly in place. • Check that the Blower Wheel spins freely. Symptom: The fan runs erratically. • Check that the Blower Wheel is firmly attached to the Motor shaft and both spin freely. 3 Symptom: The fan seems noisy.
Page 14 RN80L n RN110L Installation Guide Warranty NuTone Ventilation Fan/Lights Limited Warranty WARRANTY PERIOD: NuTone warrants to the original consumer purchaser of its NuTone Ventilation Fan/Light (the “Fan”) that your Fan (excluding lamps/ bulbs) will be materially free from defects in materials or workmanship for a period of three (3) years from the date of original purchase. The warranty on the lamps/bulbs provided with the Fan is one (1) year and does not cover lamp/bulb breakage.
LEA Y CONSERVE ESTAS INSTRUCCIONES Instalador: entregue esta guía al dueño de casa. Registre su producto en línea en el sitio www.nutone.com/register.
Página 2 RN80L n RN110L Guía para la instalación ADVERTENCIA PRECAUCIÓN PARA REDUCIR EL RIESGO DE INCENDIO, SHOCK ELÉCTRICO O DAÑOS A LAS PERSONAS, RESPETE LAS SIGUIENTES INSTRUCCIONES: 1. Utilice esta unidad sólo para el uso que describe el fabricante. Si tiene alguna pregunta, comuníquese con el fabricante a la dirección o al número de teléfono que aparece en la garantía. 2.
Página 3 RN80L n RN110L Guía para la instalación Instalación en una construcción nueva Herramientas necesarias Materiales necesarios • Destornillador eléctrico con punta Phillips • Conducto circular de metal de 4 pulg. recomendado para un mejor rendimiento. Se acepta el uso de otro tipo de conducto pero esto puede afectar el rendimiento.
Página 4 RN80L n RN110L Guía para la instalación Instalación en una construcción nueva el 3 Coloque compartimiento a presión 1 y asegúrelo 2 4 ¡Presione hasta que trabe! Ubique el compartimiento entre las vigas y ajuste el canal a ambos lados del bastidor de montaje para que el compartimiento quede asegurado en su lugar. No ajuste el compartimiento.
Página 5 RN80L n RN110L Guía para la instalación Instalación en una construcción nueva 5 Conecte los cables e instale la placa metálica • Extienda un cableado eléctrico de 120 VCA hasta el sitio de la instalación. • Utilice conectores aprobados por UL para asegurar el cableado hasta la placa metálica que se incluye en la bolsa de piezas. • Conecte los cables como se muestra en el diagrama de cableado. • No utilice un regulador de intensidad para hacer funcionar la luz.
Página 6 RN80L n RN110L Guía para la instalación Instalación en una construcción nueva la 6 Introduzca máscara y acondicione el techo La máscara protege la unidad durante la construcción. Retírela antes de instalar la rejilla. • Instale el material del techo. • Corte alrededor del compartimiento. 7 Instale la rejilla 1 2 3 8 Instale las lámparas 3 Lámpara de noche (comprar por separado) 2 1 4 Consulte la página 12 sobre Funcionamiento y Limpieza y mantenimiento.
Página 7 RN80L n RN110L Guía para la instalación Instalación en modernizaciones Herramientas necesarias Materiales necesarios • Destornillador eléctrico con punta Phillips • Regla • Destornillador Phillips • Lápiz • Cinta para sellar las conexiones de los conductos • Destornillador de cabeza plana • Sierra para paneles de yeso • Pinza • Martillo de orejas o palanca • Pelacable para la aislación de los cables • Cuchillo multiuso • Los conductos rígidos existentes requerirán el agregado de tram
Página 8 RN80L n RN110L Guía para la instalación Instalación en modernizaciones 5 Retire el conjunto del ventilador Aparte el conjunto del ventilador 2 Ambos lados 3 1 6 Retire el panel con los cables Aparte el panel con los cables Aparte el perno 1 2 7 Introduzca el bastidor de montaje 4 3 5 1 Retire los pernos del bastidor de montaje y apártelos 2 Despliegue las cuatro pestañas
Página 9 RN80L n RN110L Guía para la instalación Instalación en modernizaciones 8 Asegure el bastidor de montaje Pernos apartados en el Paso 7 9 Coloque el compartimiento a presión ¡Presione hasta que trabe! 2 1 Tire del cableado existente en el compartimiento mientras lo introduce en el bastidor de montaje 10 Fije el reborde, la transición, y los conductos 4 Introduzca el conducto existente en el compartimiento Perno de la bolsa de piezas Conducto de 4 pulg.
Página 10 RN80L n RN110L Guía para la instalación Instalación en modernizaciones 11 Instale la placa metálica, conecte los cables e instale el panel de cableado • Utilice conectores aprobados por UL para asegurar el cableado hasta la placa metálica que se incluye en la bolsa de piezas. • Conecte los cables como se muestra en el diagrama de cableado. • No utilice un regulador de intensidad para hacer funcionar la luz.
Página 11 RN80L n RN110L Guía para la instalación Instalación en modernizaciones 12 Introduzca y asegure el conjunto del ventilador 2 3 Pernos de la bolsa de piezas 1 13 Si fuera necesario efectuar reparaciones en el techo, coloque la máscara en el compartimiento después de asegurar el conjunto del ventilador. Consulte el Paso 6 de Instalación en una construcción nueva. Retire la máscara antes de instalar la rejilla.
3 Página 12 14 RN80L n RN110L Guía para la instalación Instale las lámparas 3 Lámpara de noche (comprar por separado) 2 1 ADVERTENCIA Antes de realizar el servicio o de limpiar la unidad, corte el suministro eléctrico en el panel de servicio y bloquee el servicio desconectando los medios que evitan que se conecte la energía en forma accidental.
Página 13 RN80L n RN110L Guía para la instalación Identificación y solución de fallas Repuestos 1 Síntoma: El ventilador no funciona. • Verifique la presencia de un fusible o interruptor abierto en el panel de servicios del edificio. 2 • Verifique que la conexion del motor está bien unidas. • Verifique que el ventilador centrífugo gire libremente. Síntoma: El ventilador funciona en forma errática. • Verifique que el ventilador centrífugo esté fijo al eje del motor y que ambos giren libremente.
Página 14 RN80L n RN110L Guía para la instalación Garantía Garantía limitada para las luces/ventilador para ventilación NuTone PERÍODO DE LA GARANTÍA: NuTone le garantiza al comprador consumidor original de su luz/ventilador para ventilación NuTone (el “Ventilador”) que su ventilador (a excepción de lámparas/lamparillas) no presentará defectos de material o de mano de obra durante un período de tres (3) años a partir de la fecha de la compra original.