Quick Start Guide

Quick Start Guide
Getting Started
Troubleshoot Guide
PIC
®
Percision Induction Cooktops
PIC
®
Percision Induction Cooktops
PIC Flex
Part #: 30532
9-Inch Ceramic Non-Stick
Fry Pan*
Part #: 32109
(Optional with certain models)
What you get
Temperatures and times can be adjusted on all functions before and during the cooking process.
Start cooking. 375˚F (191˚C) for 1 hour are the defaults.
Press Start to begin cooking.
Note: Press Pause/Clear during cooking to pause the PIC. Press Start to resume. Press Pause/Clear twice to clear.
Changing Fahrenheit to Celsius.
Press Prog. Press - once to display Fahrenheit. Press - again to display Celsius. Press Pause/Clear to nish.
Adjust cooking temperature.
Increase or decrease the temperature manually by selecting one of the six temperature settings or by pressing + or - to adjust the
temperature by 10-degree increments (6° then 5°C and then alternates all the way up).
Note: Refer to the owner’s manual for details.
Changing cooking time while cooking.
Cook for a specic time, or longer than 1 hour. Press Time, then press + or - to adjust the time.
Note: The ashing digit is the number being altered.
Stage/Program cooking.
Program the PIC Flex to cook at different temperatures for different amounts of time. Ex: High for 5 min. then Low for 3 min.
Press Prog to set the stages. Press High, Time and then press + ve times for 5 min. at High. Press Low, Time, and then press +
three times for 3 min. at Low. Press Start to begin cooking.
Note: You can add additional stages by repeating steps above with your desired temperature and time before pressing Start.
Compatible Cookware
Three simple ways to check if your existing pots and pans or
future cookware purchases are compatible with the NuWave
PIC Flex:
1. A magnet is typically a great indicator. If it sticks to the bottom
of a piece of cookware this typically means the pot or pan
is induction-ready. However, be cautioned that there are
instances when a cooking vessel’s magnetic properties may
not be strong enough for the pot to work efciently with the
PIC Flex.
2. Place a small amount of water in a pot or pan.
If induction compatible, water will begin to boil.
3. An induction-ready symbol may be printed on
the bottom of the cookware.
E1 Error
An E1 reading typically means that your PIC Flex does not detect
cookware on its surface. This can occur for one of two reasons:
1. The induction coils contained within the PIC Flex will
only work when they are in direct contact with a piece of
cookware. To maintain your appliance’s effectiveness,
always ensure that it rests on a at surface and that contact
is consistent with your cookware.
2. An E1 message may also occur if your chosen cookware is
not induction-ready.
When an E1 error occurs the PIC will beep every 2 seconds until
it detects a pot. If the PIC has not detected a pot after 1 minute,
it will shut off automatically. In order to resume cooking, place
induction-ready cookware on the PIC’s surface then press Start.
E7 Error & Cooking Fan
An E7 error is displayed when the PIC becomes overheated.
This is typically caused by obstruction of the PIC’s underside
Cooling Fan. Always ensure that the PIC Flex is placed on a
at, level surface with the cooling fan unobstructed. Typical
interferences include tablecloths, wooden cutting boards,
place mats, etc.
PIC & Pacemakers
Scientic tests have proven inconclusive as to whether
the electrical eld will disrupt the function of a pacemaker.
Please consult your doctor or medical professional for
guidance before use.
©2020 NuWave LLC • All Rights Reserved. • Customer Service: 1-877-689-2838 • [e-mail]
Item No: BQ30501-30532-• Rev. 11-OG • 11-23-20 • DV01 PC1