GeForce FX/MX Series VGA Card User's Guide
Declaration of Conformity According to 47 CFR, Parts 2 and 15 of the FCC Rules The following designated product: EQUIPMENT: VGA Card is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Disclaimer The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organization of such changes.
CONTENTS Chapter 1 Introduction .............................................................. 1 Product Specifications...........................................................................................1 Package Contents ..................................................................................................2 System Requirements............................................................................................2 Chapter 2 Hardware Setup ............................................
Chapter 1 Chapter 1 Introduction Product Specifications Interface - AGP 2x/4x/8x and AGP texturing support Chipset - NVIDIA GeForce FX / MX Series GPU Memory Interface - Supports 64 /128/256 MB DDR SDRAM Features (For MX Series) - 64 / 128-bit memory interface - 256-bit graphics architecture - 350 MHz internal RAMDAC (Integrated dual DACs) - NVIDIA nView Multi-Display Technology - Cube environment mapping - NVIDIA Shading Rasterizer technology - Integrated hardware T & L - MX Memory Crossbar (dual memory c
Chapter 1 reduced blanking Single-Link external TMDS (DVI 1.0), max resolution over digital port: 1600*1200*60Hz (VESA STD) (MX series only) Full Software Support - Microsoft DirectX optimizations and support - Full OpenGL 1.3/1.4 and lower support - Complete support DirectX 8.x/9.0 and lower - WHQL-certified Windows 9x / ME / 2000 / XP Other Features - TV-out - VIVO (Optional) - DVI-I (Optional) - Package Contents 1. 2. 3.
Chapter 2 Chapter 2 Hardware Setup Installing the Hardware 1. 2. 3. 4. 5. 6. Turn off the computer's power and make sure the system is properly grounded (leave the power cord connected). Then disconnect the monitor signal cable. Remove the computer chassis cover. Be sure to discharge your body's static electricity by touching the metal area of the computer each time before touching both the old and new VGA cards. Remove the old card, if it exists.
Chapter 2 5. 6. Visez la carte au châssis, et remonté le couvercle du boîtier. Branchez le cordon VGA à la carte graphique et reconnectez votre moniteur ainsi que le reste des câbles. 하드웨어 설치 1. 먼저 컴퓨터의 전원을 차단하고 전원이 완전히 차단되었는지 확인한 후에 모니터 시그널 케이블을 분리해 주십시오. 2. 컴퓨터 케이스의 덮개를 열고 VGA 카드를 장착하기에 앞서 컴퓨터를 전자기로부터 보호하기 위해 전자기로부터 안전한 복장 및 도구를 착용하거나 이용해 주십시오. 3. 만약 구형카드가 시스템에 장착되어 있다면 먼저 구형카드를 시스템에서 분리해 주십시오. 4. 케이스 뒷면 브라켓 장착 부분과 AGP 확장 슬롯에 수직이 되도록 하여 카드를 조심스럽게 AGP 확장 슬롯에 장착해 주십시오. 5.
Chapter 4 Chapter 3 Driver Setup Display Drivers Setup For Driver setup in Win98se/ME/2000/XP mode, please follow the steps below. 1. Insert VGA Driver Package CD into CD-ROM driver. 2. 3. 4. Please click on [Display Drivers] to begin driver installations. Please click [Yes] to continue. Please select [Yes] to restart computer now or [No] for restart later, then click [Finish] to complete the installation. Display properties Select from [Start] -> [Settings] -> [Control Panel] ->[Display Properties].
Appendix Appendix WinCinema (Optional) Installations of WinDVD, WinDVD Creator Setup and WinRip 2.1 Setup are included. 1. Click [WinCinema] to begin WinCinema installations. 2. Please click [I have] and enter personal information on boxes below. 3. Choose [Select All] to select all the products. Click [Next >] to proceed. DirectX 9.0 (FX Series Only) 1. If the system has an older version of DirectX, please click [DIRECTX 9.0] to upgrade to the latest version. 2. 3. 4.
NOTE NOTE All rights are reserved for the products and corporate names/logos that appear in this manual to their original owners. All rights are reserved for changing this manual and all the information/ content is subject to change without notice.
