User's Guide

22 JN-DS-JN5168-001-Myy 1v1 © NXP Laboratories UK 2012
A.8.1 Antennas approved by FCC for use with JN5168 modules
Brand
Model Number
Description
Gain (dBi)
Connector type
1
Antenna Factor
ANT-2.4-CW-RCT-RP
Vertical - knuckle antenna
2.2
RP-SMA
2
Antennova
2010B6090-01
Vertical - knuckle antenna
2.2
RP-SMA
3
Hyperlink Technology
HG2402RD-RSF
Vertical - knuckle antenna
2.2
RP-SMA
4
Aveslink Technology, Inc
E-0005-AC
Vertical- flying lead
2
RP-SMA
5
Aveslink Technology, Inc
E-2411-GC
Vertical - swivel
2
RP-SMA
6
Aveslink Technology, Inc
E-2410-CA
Vertical - bulkhead- flying lead
2
uFL
7
Aveslink Technology, Inc
E-2410-GC
Vertical - swivel
2
RP-SMA
8
Aveslink Technology, Inc
E-2820-CA
Vertical - bulkhead- flying lead
2
uFL
9
Aveslink Technology, Inc
E-2820-GC
Vertical - swivel
2
RP-SMA
10
Embedded Antenna Design
FBKR35068-RS-KR
Vertical - knuckle antenna
2
RP-SMA
11
Nearson
S131CL-L-PX-2450S
Vertical - knuckle-flying lead
2
uFL
12
Laird Technologies
WRR2400-IP04
Vertical - knuckle-flying lead
1.5
uFL
13
Laird Technologies
WRR2400-RPSMA
Vertical - knuckle-flying lead
1.3
RP-SMA
14
Aveslink Technology, Inc
E-6170-DA
Vertical - right angle
1
uFL
15
Laird Technologies
WCR2400-SMRP
Vertical - knuckle antenna
1
RP-SMA
This device has been designed to operate with the antennas listed above, and having a maximum gain of 2.2 dBi.
Alternative vertical antennas may be used provided that the gain does not exceed 2.2 dBi. Antennas having a gain
greater than 2.2 dBi are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
A.8.2 High Power Module usage limitation
The high power module variants are classified as „mobile‟ device pursuant with FCC § 2.1091 and must not be used
at a distance of < 20 cm (8”) from any people. This applies to the JN5168-001-M06 module type (TYOJN5168M6).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with
another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this
RF module in the user manual of the end product.
The user manual for the end product must include the following information in a prominent location;
“To comply with FCC‟s RF radiation exposure requirements, the antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.”
A.8.3 FCC End Product Labelling
The final „end product‟ should be labelled in a visible area with the following:
“Contains TX FCC ID: TYOJN5168M0, TYOJN5168M3, TYOJN5168M5 or TYOJN5168M6” to reflect the version of
the module being used inside the product.