User's Guide

22 JN-DS-JN5168-001-Myy 1v0 © NXP Laboratories UK 2012
A.9 Industry Canada Statement
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropic radiated power (e.i.r.p.) is not more than that permitted for successful communication.
These modules have been designed to operate with antennas having a maximum gain of 2.2 dBi. Antennas having a
gain greater than 2.2 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc).
A.9.1 Industry Canada End Product Labelling
For Industry Canada purposes the following should be used.
“Contains Industry Canada ID IC: 7438A-CYO5168M0, IC: 7438A-CYO5168M3, IC: 7438A-CYO5168M5 or IC:
7438A-CYO5168M6” to reflect the version of the module being used inside the product.
A.10 European R & TTE Directive 1999/5/EC Statement
All modules listed in this datasheet with the exception of the JN5168-001-M06 are compliant with ETSI EN 300 328
V1.7.1 (2006-10), EMC, EN 301 489-17 v2.1.1 (2009-02) and the Basic Safety Assessment (BSA) EN 60950-1:2006
(2006-06) and are subject to a Notified Body Opinion.
The modules are approved for use with the antennas listed in the following table. The JN5168-001-M06 module is not
approved for use in Europe, instead use the JN5168-001-M05 which produces the maximum permitted power.
Alternative vertical antennas may be used provided that the gain does not exceed 2.2 dBi.
Brand Model Number Description Gain (dBi) Connector type
1
Antenna Factor
ANT-2.4-CW-RCT-SMA
Vertical - knuckle antenna
2.2
SMA
2
Antennova
B6090
Vertical - knuckle antenna
2.2
RP-SMA
3
Hyperlink Technology
HG2402RD-RSF
Vertical - knuckle antenna
2.2
RP-SMA
4
Aveslink Technology, Inc
E-0005-AC
Vertical- flying lead
2
RP-SMA
5 Aveslink Technology, Inc E-2411-GC Vertical - swivel 2 RP-SMA
6 Aveslink Technology, Inc E-2410-CA Vertical - bulkhead- flying lead 2 uFL
7
Aveslink Technology, Inc
E-2410-GC
Vertical - swivel
2
RP-SMA
8
Aveslink Technology, Inc
E-2820-CA
Vertical - bulkhead- flying lead
2
uFL
9
Aveslink Technology, Inc
E-2820-GC
Vertical - swivel
2
RP-SMA
10
Embedded Antenna Design
FBKR35068-RS-KR
Vertical - knuckle antenna
2
RP-SMA
11 Nearson S131CL-L-PX-2450S Vertical - knuckle-flying lead 2 uFL
12 Laird Technologies WRR2400-IP04 Vertical - knuckle-flying lead 1.5 uFL
13 Laird Technologies WRR2400-RPSMA Vertical - knuckle-flying lead 1.3 RP-SMA
14
Aveslink Technology, Inc
E-6170-DA
Vertical - right angle
1
uFL
15
Laird Technologies
WCR2400-SMRP
Vertical - knuckle antenna
1
RP-SMA