Datasheet

LPC111X All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet Rev. 9.2 — 26 March 2014 121 of 127
NXP Semiconductors
LPC1110/11/12/13/14/15
32-bit ARM Cortex-M0 microcontroller
17. Revision history
Table 34. Revision history
Document ID Release date Data sheet status Change notice Supersedes
LPC111X v.9.2 20140326 Product data sheet - LPC111X v.9.1
Modifications:
• Pin description tables for RESET/PIO0_0 updated: In deep power-down mode, this pin
must be pulled HIGH externally. The RESET pin can be left unconnected or be used
as a GPIO pin if an external RESET
function is not needed. See Section 6.2.
• Pin description notes relating to open-drain I2C-bus pins updated for clarity in
Section 6.2.
• Pin description of the WAKEUP pin updated for clarity. See Section 6.2.
• Parts added: LPC1114JHI33/303, LPC1111JHN33/103, LPC1112JHN33/203,
LPC1113JHN33/203, LPC1114JHN33/303, LPC1114JBD48/333, LPC1112FHI33/102,
LPC1114JBD48/303, LPC1114JBD48/323, LPC1113JBD48/303, LPC1113JHN33/303,
LPC1112JHN33/103, LPC1111JHN33/203, LPC1114JHN33/203.
LPC111X v.9.1 20131213 Product data sheet - LPC111X v.9
Modifications:
• Table 17 “Static characteristics (LPC1100XL series)”:
– Added I
DD
max spec for Deep-sleep and Deep power-down modes @ 25 C and
105 C.
– Added Table note 11 “105 °C spec applies only to the LPC1112JHI33,
LPC1114JHN33, LPC1115JBD48, and LPC1115JET48 parts.”
– Updated Table note 12 “WAKEUP pin and RESET pin are pulled HIGH externally.”
• Table 16 “Static characteristics (LPC1100, LPC1100L series)”:
– Updated Table note 9 “WAKEUP pin and RESET pin are pulled HIGH externally.”
LPC111X v.9 20131029 Product data sheet - LPC111X v.8.2
Modifications:
• Added LPC1112JHI33/203, LPC1114JHN33/333, LPC1115JBD48/303, and
LPC1115JET48/303 parts.
• Removed t
clk(H)
and t
clk(L)
from Figure 47 “SPI master timing in SPI mode” and Figure
48 “SPI slave timing in SPI mode”; spec not characterized.
• Table 22 “Power-up characteristics[1]”: Added table note “Does not apply to
LPC1100XL series”.
LPC111X v.8.2 20130805 Product data sheet - LPC111X v.8.1
Modifications:
• Added LPC1115FET48/303.
LPC111X v.8.1 20130524 Product data sheet - LPC111X v.8
Modifications:
• Table 4 thru Table 11: Added “5 V tolerant pad” to RESET/PIO0_0 table note.
• Added Section 9 “Thermal characteristics”.
• SRAM size corrected for part LPC1112FHN24/202 (4 kB). See Table 2.
LPC111X v.8 20130220 Product data sheet - LPC111X v.7.5
Modifications:
• Table 16 “Static characteristics” added Pin capacitance section.
• Default pin state corrected for pins PIO0_4 and PIO0_5 (I; IA) in Table 11 “LPC1100XL
series: LPC1111/12/13/14 pin description table (HVQFN33 package)”.
• Table 12 “Limiting values” expanded for clarity.
• Table 19 “ Power consumption at very low frequencies using the watchdog oscillator”
added.
• Added Section 12.2 “Use of ADC input trigger signals”.
• Added Section 12.8 “ADC effective input impedance”.
LPC111X v.7.5 20121002 Product data sheet - LPC111X v.7.4