Datasheet
Table Of Contents
- 1. General description
- 2. Features and benefits
- 3. Applications
- 4. Ordering information
- 5. Block diagram
- 6. Pinning information
- 7. Functional description
- 7.1 Architectural overview
- 7.2 On-chip flash programming memory
- 7.3 On-chip SRAM
- 7.4 Memory map
- 7.5 Interrupt controller
- 7.6 Pin connect block
- 7.7 General purpose DMA controller
- 7.8 Fast general purpose parallel I/O
- 7.9 Ethernet (LPC2362 only)
- 7.10 USB interface
- 7.11 CAN controller and acceptance filters
- 7.12 10-bit ADC
- 7.13 10-bit DAC
- 7.14 UARTs
- 7.15 SPI serial I/O controller
- 7.16 SSP serial I/O controller
- 7.17 I2C-bus serial I/O controllers
- 7.18 I2S-bus serial I/O controllers
- 7.19 General purpose 32-bit timers/external event counters
- 7.20 Pulse width modulator
- 7.21 Watchdog timer
- 7.22 RTC and battery RAM
- 7.23 Clocking and power control
- 7.24 System control
- 7.25 Emulation and debugging
- 8. Limiting values
- 9. Thermal characteristics
- 10. Static characteristics
- 11. Dynamic characteristics
- 12. ADC electrical characteristics
- 13. DAC electrical characteristics
- 14. Application information
- 15. Package outline
- 16. Abbreviations
- 17. Revision history
- 18. Legal information
- 19. Contact information
- 20. Contents
LPC2361_62 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2013. All rights reserved.
Product data sheet Rev. 5.1 — 15 October 2013 53 of 65
NXP Semiconductors
LPC2361/62
Single-chip 16-bit/32-bit MCU
Fig 23. Oscillator modes and models: oscillation mode of operation and external crystal
model used for C
X1
/C
X2
evaluation
Table 15. Recommended values for C
X1
/C
X2
in oscillation mode (crystal and external
components parameters): low frequency mode
Fundamental oscillation
frequency F
OSC
Crystal load
capacitance C
L
Maximum crystal
series resistance R
S
External load
capacitors C
X1
/C
X2
1 MHz to 5 MHz 10 pF < 300 18 pF, 18 pF
20 pF < 300 39 pF, 39 pF
30 pF < 300 57 pF, 57 pF
5 MHz to 10 MHz 10 pF < 300 18 pF, 18 pF
20 pF < 200 39 pF, 39 pF
30 pF < 100 57 pF, 57 pF
10 MHz to 15 MHz 10 pF < 160 18 pF, 18 pF
20 pF < 60 39 pF, 39 pF
15 MHz to 20 MHz 10 pF < 80 18 pF, 18 pF
Table 16. Recommended values for C
X1
/C
X2
in oscillation mode (crystal and external
components parameters): high frequency mode
Fundamental oscillation
frequency F
OSC
Crystal load
capacitance C
L
Maximum crystal
series resistance R
S
External load
capacitors C
X1
, C
X2
15 MHz to 20 MHz 10 pF < 180 18 pF, 18 pF
20 pF < 100 39 pF, 39 pF
20 MHz to 25 MHz 10 pF < 160 18 pF, 18 pF
20 pF < 80 39 pF, 39 pF
002aag469
LPC2xxx
XTAL1 XTAL2
C
X2
C
X1
XTAL
=
C
L
C
P
R
S
L