Datasheet

56F8356 Technical Data, Rev. 13
2 Freescale Semiconductor
Preliminary
Document Revision History
Version History Description of Change
Rev 1.0
Initial Public Release
Rev 2.0
Added Package Pins to GPIO Table in Part 8 General Purpose Input/Output (GPIO). Added
“Typical Min” values to Table 10-18. Editing grammar, spelling, consistency of language
throughout family. Updated values in Regulator Parameters Table 10-9, External Clock
Operation Timing Requirements Table 10-13, SPI Timing Table 10-18, ADC Parameters
Table 10-24, and IO Loading Coefficients at 10MHz Table 10-25.
Rev 3.0
Added Part 4.8, added the word “access” to FM Error Interrupt in Table 4-5, documenting only
Typ. numbers for LVI in Table 10-6, updated EMI numbers and writeup in Part 10.8.
Rev 4.0
Updated numbers in Table 10-7 and Table 10-8 with more recent data, Corrected typo in
Table 10-3 in Pd characteristics.
Rev 5.0
Replace any reference to Flash Interface Unit with Flash Memory Module; corrected thermal
numbers for 144 LQFP in Table 10-3; removed unneccessary notes in Table 10-12; corrected
temperature range in Table 10-14; added ADC calibration information to Table 10-24 and new
graphs in Figure 10-22
Rev 6.0
Adding/clarifing notes to Table 4-4 to help clarify independent program flash blocks and other
Program Flash modes, clarification to Table 10-23, corrected Digital Input Current Low (pull-up
enabled) numbers in
Table 10-5. Removed text and Table 10-2; replaced with note to
Table 10-1.
Rev 7.0 Added 56F8156 information; edited to indicate differences in 56F8356 and 56F8156. Refor-
matted for Freescale look and feel. Updated Temperature Sensor and ADC tables, then
updated balance of electrical tables for consistency throughout family. Clarified I/O power
description in Table 2-2, added note to Table 10-7 and clarified Section 12.3.
Rev 8.0 Added output voltage maximum value and note to clarify in Table 10-1; also removed overall
life expectancy note, since life expectancy is dependent on customer usage and must be
determined by reliability engineering. Clarified value and unit measure for Maximum allowed
P
D
in Table 10-3. Corrected note about average value for Flash Data Retention in Table 10-4.
Added new RoHS-compliant orderable part numbers in Table 13-1.
Rev 9.0 Updated Table 10-24 to reflect new value for maximum Uncalibrated Gain Error
Rev 10.0 Deleted RSTO from Pin Group 2 (listed after Table 10-1). Deleted formula for Max Ambient
Operating Temperature (Automotive) and Max Ambient Operating Temperature (Industrial) in
Table 10-4. Added RoHS-compliance and “pb-free” language to back cover.
Rev 11.0 Added information/corrected state during reset in Table 2-2. Clarified external reference crys-
tal frequency for PLL in Table 10-14 by increasing maximum value to 8.4MHz..
Rev 12.0 Replaced “Tri-stated” with an explanation in State During Reset column in Table 2-2.
Rev. 13
• Added the following note to the description of the TMS signal in Table 2-2:
Note: Always tie the TMS pin to V
DD
through a 2.2K resistor.
• Added the following note to the description of the TRST
signal in Table 2-2:
Note: For normal operation, connect TRST
directly to V
SS
. If the design is to be used in a debugging
environment, TRST
may be tied to V
SS
through a 1K resistor.
Please see http://www.freescale.com for the most current data sheet revision.