Datasheet
Table Of Contents
- Revision History
- List of Chapters
- Table of Contents
- Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
- 1.5.1 Power Supply Pins (VDD and VSS)
- 1.5.2 Oscillator Pins (OSC1 and OSC2)
- 1.5.3 External Reset Pin (RST)
- 1.5.4 External Interrupt Pin (IRQ)
- 1.5.5 CGM Power Supply Pins (VDDA and VSSA)
- 1.5.6 External Filter Capacitor Pin (CGMXFC)
- 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
- 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8)
- 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0)
- 1.5.10 Port C I/O Pins (PTC6-PTC0)
- 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS)
- 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD)
- 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0)
- 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16)
- 1.5.15 Unused Pin Termination
- Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
- Chapter 3 Analog-to-Digital Converter (ADC)
- Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.4.1 Crystal Amplifier Input Pin (OSC1)
- 4.4.2 Crystal Amplifier Output Pin (OSC2)
- 4.4.3 External Filter Capacitor Pin (CGMXFC)
- 4.4.4 PLL Analog Power Pin (Vdda)
- 4.4.5 PLL Analog Ground Pin (Vssa)
- 4.4.6 Oscillator Enable Signal (SIMOSCEN)
- 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
- 4.4.8 Crystal Output Frequency Signal (CGMXCLK)
- 4.4.9 CGM Base Clock Output (CGMOUT)
- 4.4.10 CGM CPU Interrupt (CGMINT)
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
- Chapter 5 Configuration Register (CONFIG)
- Chapter 6 Computer Operating Properly (COP) Module
- Chapter 7 Central Processor Unit (CPU)
- Chapter 8 External Interrupt (IRQ)
- Chapter 9 Keyboard Interrupt Module (KBI)
- Chapter 10 Low-Power Modes
- 10.1 Introduction
- 10.2 Analog-to-Digital Converter (ADC)
- 10.3 Break Module (BRK)
- 10.4 Central Processor Unit (CPU)
- 10.5 Clock Generator Module (CGM)
- 10.6 Computer Operating Properly Module (COP)
- 10.7 External Interrupt Module (IRQ)
- 10.8 Keyboard Interrupt Module (KBI)
- 10.9 Low-Voltage Inhibit Module (LVI)
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
- 10.11 Serial Peripheral Interface Module (SPI)
- 10.12 Timer Interface Module (TIM1 and TIM2)
- 10.13 Timebase Module (TBM)
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
- Chapter 11 Low-Voltage Inhibit (LVI)
- Chapter 12 Input/Output (I/O) Ports
- Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- Chapter 14 System Integration Module (SIM)
- Chapter 15 Serial Peripheral Interface (SPI) Module
- Chapter 16 Timebase Module (TBM)
- Chapter 17 Timer Interface Module (TIM1)
- Chapter 18 Timer Interface Module (TIM2)
- Chapter 19 Development Support
- Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
- Chapter 21 Ordering Information and Mechanical Specifications
- Appendix A MC68HC908GR48A
- Appendix B MC68HC908GR32A
External Interrupt Module (IRQ)
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
Freescale Semiconductor 123
10.7 External Interrupt Module (IRQ)
10.7.1 Wait Mode
The external interrupt (IRQ) module remains active in wait mode. Clearing the IMASK bit in the IRQ status
and control register enables IRQ
CPU interrupt requests to bring the MCU out of wait mode.
10.7.2 Stop Mode
The IRQ module remains active in stop mode. Clearing the IMASK bit in the IRQ status and control
register enables IRQ
CPU interrupt requests to bring the MCU out of stop mode.
10.8 Keyboard Interrupt Module (KBI)
10.8.1 Wait Mode
The keyboard interrupt (KBI) module remains active in wait mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring the MCU out of wait
mode.
10.8.2 Stop Mode
The keyboard module remains active in stop mode. Clearing the IMASKK bit in the keyboard status and
control register enables keyboard interrupt requests to bring the MCU out of stop mode.
10.9 Low-Voltage Inhibit Module (LVI)
10.9.1 Wait Mode
If enabled, the low-voltage inhibit (LVI) module remains active in wait mode. If enabled to generate resets,
the LVI module can generate a reset and bring the MCU out of wait mode.
10.9.2 Stop Mode
If enabled, the LVI module remains active in stop mode. If enabled to generate resets, the LVI module
can generate a reset and bring the MCU out of stop mode.
10.10 Enhanced Serial Communications Interface Module (ESCI)
10.10.1 Wait Mode
The enhanced serial communications interface (ESCI), or SCI module for short, module remains active
in wait mode. Any enabled CPU interrupt request from the SCI module can bring the MCU out of wait
mode.
If SCI module functions are not required during wait mode, reduce power consumption by disabling the
module before executing the WAIT instruction.
10.10.2 Stop Mode
The SCI module is inactive in stop mode. The STOP instruction does not affect SCI register states. SCI
module operation resumes after the MCU exits stop mode.
Because the internal clock is inactive during stop mode, entering stop mode during an SCI transmission
or reception results in invalid data.