Datasheet
Table Of Contents
- Revision History
- List of Chapters
- Table of Contents
- Chapter 1 General Description
- 1.1 Introduction
- 1.2 Features
- 1.3 MCU Block Diagram
- 1.4 Pin Assignments
- 1.5 Pin Functions
- 1.5.1 Power Supply Pins (VDD and VSS)
- 1.5.2 Oscillator Pins (OSC1 and OSC2)
- 1.5.3 External Reset Pin (RST)
- 1.5.4 External Interrupt Pin (IRQ)
- 1.5.5 CGM Power Supply Pins (VDDA and VSSA)
- 1.5.6 External Filter Capacitor Pin (CGMXFC)
- 1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
- 1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15-PTA0/KBD0/AD8)
- 1.5.9 Port B I/O Pins (PTB7/AD7-PTB0/AD0)
- 1.5.10 Port C I/O Pins (PTC6-PTC0)
- 1.5.11 Port D I/O Pins (PTD7/T2CH1-PTD0/SS)
- 1.5.12 Port E I/O Pins (PTE5-PTE2, PTE1/RxD, and PTE0/TxD)
- 1.5.13 Port F I/O Pins (PTF7/T2CH5-PTF0)
- 1.5.14 Port G I/O Pins (PTG7/AD23-PTBG0/AD16)
- 1.5.15 Unused Pin Termination
- Chapter 2 Memory
- 2.1 Introduction
- 2.2 Unimplemented Memory Locations
- 2.3 Reserved Memory Locations
- 2.4 Input/Output (I/O) Section
- 2.5 Random-Access Memory (RAM)
- 2.6 FLASH-1 Memory (FLASH-1)
- 2.7 FLASH-2 Memory (FLASH-2)
- Chapter 3 Analog-to-Digital Converter (ADC)
- Chapter 4 Clock Generator Module (CGM)
- 4.1 Introduction
- 4.2 Features
- 4.3 Functional Description
- 4.4 I/O Signals
- 4.4.1 Crystal Amplifier Input Pin (OSC1)
- 4.4.2 Crystal Amplifier Output Pin (OSC2)
- 4.4.3 External Filter Capacitor Pin (CGMXFC)
- 4.4.4 PLL Analog Power Pin (Vdda)
- 4.4.5 PLL Analog Ground Pin (Vssa)
- 4.4.6 Oscillator Enable Signal (SIMOSCEN)
- 4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
- 4.4.8 Crystal Output Frequency Signal (CGMXCLK)
- 4.4.9 CGM Base Clock Output (CGMOUT)
- 4.4.10 CGM CPU Interrupt (CGMINT)
- 4.5 CGM Registers
- 4.6 Interrupts
- 4.7 Special Modes
- 4.8 Acquisition/Lock Time Specifications
- Chapter 5 Configuration Register (CONFIG)
- Chapter 6 Computer Operating Properly (COP) Module
- Chapter 7 Central Processor Unit (CPU)
- Chapter 8 External Interrupt (IRQ)
- Chapter 9 Keyboard Interrupt Module (KBI)
- Chapter 10 Low-Power Modes
- 10.1 Introduction
- 10.2 Analog-to-Digital Converter (ADC)
- 10.3 Break Module (BRK)
- 10.4 Central Processor Unit (CPU)
- 10.5 Clock Generator Module (CGM)
- 10.6 Computer Operating Properly Module (COP)
- 10.7 External Interrupt Module (IRQ)
- 10.8 Keyboard Interrupt Module (KBI)
- 10.9 Low-Voltage Inhibit Module (LVI)
- 10.10 Enhanced Serial Communications Interface Module (ESCI)
- 10.11 Serial Peripheral Interface Module (SPI)
- 10.12 Timer Interface Module (TIM1 and TIM2)
- 10.13 Timebase Module (TBM)
- 10.14 Exiting Wait Mode
- 10.15 Exiting Stop Mode
- Chapter 11 Low-Voltage Inhibit (LVI)
- Chapter 12 Input/Output (I/O) Ports
- Chapter 13 Enhanced Serial Communications Interface (ESCI) Module
- Chapter 14 System Integration Module (SIM)
- Chapter 15 Serial Peripheral Interface (SPI) Module
- Chapter 16 Timebase Module (TBM)
- Chapter 17 Timer Interface Module (TIM1)
- Chapter 18 Timer Interface Module (TIM2)
- Chapter 19 Development Support
- Chapter 20 Electrical Specifications
- 20.1 Introduction
- 20.2 Absolute Maximum Ratings
- 20.3 Functional Operating Range
- 20.4 Thermal Characteristics
- 20.5 5.0-Vdc Electrical Characteristics
- 20.6 3.3-Vdc Electrical Characteristics
- 20.7 5.0-Volt Control Timing
- 20.8 3.3-Volt Control Timing
- 20.9 Clock Generation Module (CGM) Characteristics
- 20.10 5.0-Volt ADC Characteristics
- 20.11 3.3-Volt ADC Characteristics
- 20.12 5.0-Volt SPI Characteristics
- 20.13 3.3-Volt SPI Characteristics
- 20.14 Timer Interface Module Characteristics
- 20.15 Memory Characteristics
- Chapter 21 Ordering Information and Mechanical Specifications
- Appendix A MC68HC908GR48A
- Appendix B MC68HC908GR32A
Port A
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
Freescale Semiconductor 137
12.3.3 Port A Input Pullup Enable Register
The port A input pullup enable register (PTAPUE) contains a software configurable pullup device for each
of the eight port A pins. Each bit is individually configurable and requires that the data direction register,
DDRA, bit be configured as an input. Each pullup is automatically and dynamically disabled when a port
bit’s DDRA is configured for output mode.
NOTE
Pullup or pulldown resistors are automatically selected for keyboard
interrupt pins depending on the bit settings in the keyboard interrupt polarity
register (INTKBIPR) see 9.7.3 Keyboard Interrupt Polarity Register.
PTAPUE7–PTAPUE0 — Port A Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an input port bit.
1 = Corresponding port A pin configured to have internal pullup
0 = Corresponding port A pin has internal pullup disconnected
Table 12-2. Port A Pin Functions
PTAPUE
Bit
DDRA
Bit
PTA
Bit
I/O Pin
Mode
Accesses to DDRA Accesses to PTA
Read/Write Read Write
10
X
(1)
1. X = Don’t care
Input, V
DD
(2)
2. I/O pin pulled up to V
DD
by internal pullup device
DDRA7–DDRA0 Pin
PTA7–PTA0
(3)
3. Writing affects data register, but does not affect input.
00X
Input, Hi-Z
(4)
4. Hi-Z = High impedance
DDRA7–DDRA0 Pin
PTA7–PTA0
(3)
X 1 X Output DDRA7–DDRA0 PTA7–PTA0 PTA7–PTA0
Address: $000D
Bit 7654321Bit 0
Read:
PTAPUE7 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0
Write:
Reset:00000000
Figure 12-5. Port A Input Pullup Enable Register (PTAPUE)